legrand WNRL50 Radiant Smart Dimmer Instruction Manual

: June 6, 2024
: Legrand

Table of Contents

legrand WNRL50 Radiant Smart Dimmer
FCC
BEFORE YOU START
WHAT YOU NEED
INSTALLATION & SETUP
GETTING TO KNOW YOUR DIMMER
SPECIFICATIONS
LIMITED ONE YEAR WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

legrand WNRL50 Radiant Smart Dimmer

FCC

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

this device may not cause harmful interference
this device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 10 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.

NOTE: Any changes or modiﬁcations to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.

Contains FCC ID: 2AU5D982057
IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:

this device may not cause interference
this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 10 mm to the human body. Note: Any changes or modiﬁ cations to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.
IC: 25764-982057
HVIN: 982057

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
CAUTION: To reduce the risk of injury and/or overheating and damage to other equipment:

Do not install to control a receptacle or a motor-controlled appliance.
For dry, indoor use only.
Do not use to power medical equipment.
Use ONLY with dimmable lighting loads.
Do not use with loads exceeding the device load rating.
Connect the smart dimmer to a 120 VAC, 60 Hz power source ONLY.
Always use copper wire to install the smart dimmer & follow all applicable local & national electrical codes.

WHAT YOU NEED

Required:

Phillips-head screwdriver
Flat blade screwdriver You May Also Need:

Voltage tester, pliers, wire cutter, wire stripper, electrical tape, ﬂashlight, wiring leads (included), and wire nuts (included).

INSTALLATION & SETUP

Turn Off Power To Device At Circuit Breaker
Flip existing light switch multiple times to conﬁrm power is off. NOTE: Ensure power is off to all devices in electrical box.
Remove Existing DeviceCheck for the following wires:
HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the purpose of this guide. Do not touch or let “hot” wire contact other wires.
LOAD: Directs power to your light(s).
NEUTRAL: Creates a path to return current to the power source when the device is off. Required for your dimmer installation.
GROUND: Provides a safe path for electricity in the event of a short circuit.
]Wire Smart Dimmer
Use the wire nuts provided to secure the wires together.
Connect the WHITE neutral wire on the dimmer to the neutral wires in the box, using the red wire nut.
Connect the LOAD wire on the dimmer to the load wire in the box.
Connect the HOT wire on the dimmer to the hot wire(s) in the box.
Connect the GREEN ground wire on the dimmer to the ground wire(s) in the box.
Secure Smart Dimmer
Fold wires into electrical box, taking care not to pinch a wire.
Use included screws to secure smart dimmer to electrical box. Do not fully tighten the screws.
Test The Smart Dimmer
NOTE: See getting to know your dimmer section for feature details.
Turn the power back on at the circuit breaker, press dimmer to turn light on/off and use the dimmer paddle to adjust the level of your light(s). This device is designed to work with a radiant® Smart Gateway with Netatmo. Follow the instructions from your app to ﬁnish setting up your dimmer.
TROUBLESHOOTING TIP: If the device is not powering check wiring to determine if you have reversed the “HOT” and “LOAD” wiring.
Attach Wall Plate
Use the sub-plate screws (provided) to secure the sub-plate to the smart dimmer.
Tighten device screws to secure smart dimmer to the electrical box.
Angle the UP end of the wall plate over the top edge of the sub-plate. Push the screwless wall plate down and in until it “snaps” into place over the sub-plate.
NOTE: To remove the wall plate, place the tip of a ﬂat blade screwdriver into the slot under the wall plate and twist gently.
Set Up Your System
Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
Connect your smart device to your home network by following the step by step instructions in the app.
Use the app to control your smart device.
For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrl50wh

GETTING TO KNOW YOUR DIMMER

legrand WNRL50 Radiant Smart Dimmer fig5

Reset To Factory Default

Deleting a device from the app will reset it to factory defaults.
To manually reset the device to factory defaults press and hold the EZ button for 10 seconds until you see the LED blink red then release. The LED will change to solid red when the reset is complete. legrand WNRL50 Radiant Smart
Dimmer fig4 LED Locator Light Explanations

State of Light	Explanation
Solid White	Lit when load is off.
Solid Red	Factory reset, not in network.
Blinking Green	Device is attempting to connect to the network.
Solid Green	Device in network, temporarily open.

SPECIFICATIONS

De-rating of the dimmer is not required for reverse phase applications. For forward phase applications in two-gang installations, de-rate incandescent, halogen, or electronic low voltage (ELV) loads to 600 Watts; in three-gang or greater installations, de-rate incandescent, halogen, or electronic low voltage (ELV) loads to 600 Watts on the outer units and 500 Watts on the center units.

RATING CHART

Load

| ****

Rating

| Dual- Gang| ****

3-Gang

---|---|---|---
Incandescent/Halogen/ ELV (FWD)| 700W| 600W /

600W

| 600W/500W/600W
Incandescent/Halogen/ ELV (REV)| ****

450W

CFL/LED/EFL (FWD)| 450W/ 3.8A
CFL/LED/EFL (REV)| 250W/ 2.1A
Magnetic Low Voltage (FWD)| ****

500VA

Legrand reserves the right to change speciﬁcations without notice.

NOTE: The dimmer ships in forward phase mode to accommodate most load types.
Refer to the app to enter reverse phase.

LIMITED ONE YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within ONE year from date of purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand
does not include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)
To ensure safety, all repairs to Legrand products must be made by Legrand, or under its speciﬁc direction. Procedure to obtain performance of any warranty obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction. This warranty gives you speciﬁc legal rights and you may also have other rights which vary from state to state.

For covering patents, see www.legrand.us/patents
Pour couvrir les brevets, voir www.legrand.us/patents Para cubrir las patentes, véase www.legrand.us/patents
No: 341306 2/21
© Copyright 2021 Legrand All Rights Reserved.
© Copyright 2021 Tous droits réservés Legrand.
© Copyright 2021 Legrand Todos los derechos reservados.

Questions? We’re here to help.

Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F) Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart-lighting.aspx
(Click on the chat icon to open a dialogue box)
800.223.4185 1.877.BY.LEGRAND
www.legrand.us
www.legrand.ca