BLAUPUNKT 5VT8X00EWE Fully Integrated Built-in Dishwasher Instruction Manual

BLAUPUNKT 5VT8X00EWE Fully Integrated Built-in Dishwasher

INSTRUCTION MANUAL

PRODUCT DESCRIPTION

1. Upper rack
2. Foldable flaps
3. Upper rack height adjuster
4. Upper spray arm
5. Lower rack
6. Cutlery basket
7. Lower spray arm
8. Filter Assembly
9. Salt reservoir
10. Detergent and Rinse Aid dispensers
11. Rating plate
12. Control panel
13. ON-OFF/Reset button with indicator light
14. Program selection button
15. Salt refill indicator light
16. Rinse Aid refill indicator light
17. Program number and delay time indicator
18. Tablet indicator light
19. Display
20. Zone Wash indicator lights
21. Zone Wash button
22. Delay button
23. START/PAUSE button with indicator light / Tab

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.

FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.
• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher (see PRODUCT DESCRIPTION) and must be filled when the SALT REFILL indicator light in the control panel is lit.

1. 1. Remove the lower rack and unscrew the reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt reservoir with water.
3. Position the funnel (see figure) and fill the salt reservoir right up to its edge (approximately 1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get into the container during the wash program (this could damage the water softener beyond repair). Whenever you need to add salt, it is mandatory to complete the procedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that the water hardness setting is based on the actual water hardness in your house. This information can be obtained from your local water supplier.

The factory sets the default value for the water hardness:

• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button P for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The current selection level number and the salt indicator light both flash.
• Press button P to select the desired hardness level (see WATER HARDNESS TABLE).

Water Hardness Table

Level| °dH

German degrees

| °fH

French degrees

| °Clark

English degrees

1| Soft| 0 – 6| 0 – 10| 0 – 7
2| Medium| 7 – 11| 11 – 20| 8 – 14
3| Average| 12 – 16| 21 – 29| 15 – 20
4| Hard| 17 – 34| 30 – 60| 21 – 42
5| Very hard| 35 – 50| 61 – 90| 43 – 62

• Switch off the appliance by pressing the ON/OFF button.
  Setting is complete!
  As soon as this procedure is complete, run a program without loading. Only use salt that has been specifically designed for dishwashers. After the salt has been poured into the machine, the SALT REFILL indicator light switches off. If the salt container is not filled, the water softener and the heating element may be damaged as a result of limescale accumulation. Using of Salt is recommended with any type of dishwasher detergent.

FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should be filled when the RINSE AID REFILL indicator light in the control panel is lit.

1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow from the dispenser. If this happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
   NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.

• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button P three times – a beep will be heard.
• Switch it on using the ON/OFF button.
• The current selection level number and rinse aid indicator light flash.
• Press button P to select the level of rinse aid quantity to be supplied.
• Switch it off using the ON/OFF button

The setting is complete!
If the rinse aid level is set to ZERO (ECO), no-rinse aid will be supplied. The LOW RINSE AID indicator light will not be lit if you run out of rinse aid. A maximum of 5 levels can be set according to the dishwasher model. The factory setting is specific to the model, please follow the instructions above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes, set a mid-range number (3-4).

FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the opening device C. Introduce the detergent into the dry dispenser D only. Place the amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent refer to the mentioned earlier information to add the proper quantity. Inside the dispenser D there are indications to help the detergent dosing.
2. Remove detergent residues from the edges of the dispenser and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the closing device is secured in place.

The detergent dispenser automatically opens up at the right time according to the program all-in-one detergents are used, we recommend using the TABLET button because it adjusts the program so that the best washing and drying results are always achieved. Usage of detergent not designed for dishwashers may cause malfunction or damage to the appliance.

PROGRAMS TABLE

Program

| Drying phase| ****

Available options *)

| Duration of wash program (h:min))| **

Water consumption (litres/cycle)

| ****

Energy consumption (kWh/cycle)

---|---|---|---|---|---
1. Eco| | 50°| **| | 4:00| 9.0| 0.76
2. Auto Intensive| | 50-60°| **| | 1:20 – 3:00| 7.0 – 14.0| 0.70 – 1.10
3. Intensive| | 65°| **| | 2:40| 17.0| 1.30
4. Delicates| | 45°| **| | 1:40| 12.0| 1.00
5.  Rapid 30’ __| | 45°| –| | 0:30| 9.0| 0.50
6. Soak| | –| –| | 0:10| 4.5| 0.01

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.
ECO
Eco program is suitable to clean normally soiled tableware, that for this use, it is the most efficient program in terms of its combined energy and water consumption, and that it is used to assess compliance with the EU Ecodesign legislation.

AUTO INTENSIVE
For normally soiled dishes with dried food residues. Senses the level of soiling on the dishes and adjusts the program accordingly. When the sensor is detecting the soil level an animation appears in the display and the cycle duration is updated.

I NTENSIVE
Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).

DELICATES
Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.

RAPID 30’
Program to be used for half load of lightly-soiled dishes with no dried food residues. Does not include drying phase.

SOAK
Use to refresh crockery planned to be washed later. No detergent to be used with this program.
Notes:
Please note that cycle Rapid 30’ is dedicated for lightly soiled dishes.

OPTIONS AND FUNCTIONS

OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).

ZONE WASH
If there are not many dishes to be washed, a half loading may be used in order to save water, electricity and detergent. Select the program and then press the Zone Wash button: the corresponding symbol lights up. By default the appliance washes the dishes in all racks.
To wash only the specific rack, press this button repeatedly:

• shown on the display (only lower rack)
• shown on the display (only upper rack)
• shown on the display (option is OFF and the appliance will wash dishes in all racks).
  Remember to load the upper or lower rack only, and to reduce the amount of detergent accordingly.
  If upper rack is removed, please apply detergent directly to tub instead of detergent dispenser.

DELAY
The start time of the program may be delayed for a period of time between 1 and 12 hours.

1. Press the DELAY button: the corresponding «h» symbol appears on the display; each time you press the button, the time (1h, 2h, etc. up to max. 12h) from the start of the selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE button and within 4 seconds close the door: the timer will begin counting down.
3. Once this time has elapsed, the indicator light «h» switches off and the wash cycle begins.

To adjust the delay time and select a shorter period of time, press the DELAY button. To cancel it, press the button repeatedly until the selected delayed start indicator light «h» switches off. The wash program will start automatically as soon as the door is shut. The DELAY function cannot be set once a wash cycle has been started.
TABLET (Tab)
This setting allows you to optimize the performance of the program according to the type of detergent used. Press the START/PAUSE button for 3 seconds (the corresponding symbol will light up) if you use combined detergents in tablet form (rinse aid, salt and detergent in 1 dose). If you use powder or liquid detergent, this option should be off.

LOADING THE RACKS

UPPER RACK

• Load delicate and light dishes: glasses, cups, saucers, low salad bowls.

ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper basket can be adjusted: high position to place bulky crockery in the lower basket and low position to make the most of the tip-up compartments by creating more space upwards. The upper rack is equipped with a Upper Rack height adjuster (see figure), without pressing the levers, lift it up by simply holding the rack sides, as soon as the rack is stable in its upper position. To restore to the lower position, press
the levers (A) at the sides of the rack and move the basket downwards. We strongly recommend that you do not adjust the height of the rack when it is loaded. NEVER raise or lower the basket on one side only.
FOLDABLE FLAPS WITH ADJUSTABLE POSITION The side foldable flaps can be fold or unfold to optimize the arrangement of crockery inside the rack. Wine glasses can be placed safely in the foldable flaps by inserting the stem of each glass into the corresponding slots. Depending on the model:

• to unfold the flaps there is needed to slide it up and rotate or release it from the snaps and pull it down.
• to fold the flaps there is needed to rotate it and slide flaps down or pull it up and attach flaps to the snaps.

LOWER RACK

• For pots, lids, plates, salad bowls, cutlery etc… Large plates and lids should ideally be placed at the sides to avoid interferences with the spray arm.

CUTLERY BASKET
It is fitted with top grids for improved cutlery arrangement. It must only be positioned at the front of the lower rack. Knives and other utensils with sharp edges must be placed in the cutlery basket with the points facing downwards or they must be positioned horizontally in the tip-up compartments on the upper rack.

DAILY USE

1. CHECK WATER CONNECTION
   Check that the dishwasher is connected to the water supply and that the tap is open.

2. SWITCH ON THE DISHWASHER
   Open the door and press the ON/OFF button.

3. LOAD THE RACKS (see LOADING THE RACKS).

4. FILLING THE DETERGENT DISPENSER

5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
   Select the most appropriate program in accordance with the type of crockery and its soiling level (see PROGRAMS DESCRIPTION) by pressing the P button. Select the desired options (see OPTIONS AND FUNCTIONS).

6. START
   Start the wash cycle by pressing the START/PAUSE button (led is lit) and closing the door within 4 sec. When the program starts you hear a single beep. If the door was not closed within 4sec., the alarm sound will be played. In this case, open the door, press the START/PAUSE button and close the door again within 4 sec.

7. END OF WASH CYCLE
   The end of the wash cycle is indicated by beeps and by the flashing of the wash cycle number on the display. Open the door and switch off the appliance by pressing the ON/OFF button. Wait for a few minutes before removing the crockery – to avoid burns. Unload the racks, beginning with the lower one.

The machine will switch off automatically during certain extended periods of inactivity, in order to minimize electricity consumption. If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher, reduce the amount of detergent used accordingly.

MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided that it has only just begun: open the door, press and hold the ON/OFF button, the machine will switch off.
Switch the machine back on using the ON/OFF button and select the new wash cycle and any desired options; Start the wash cycle by pressing the START/PAUSE button (led is lit) and closing the door within 4 sec.

ADDING EXTRA CROCKERY
Without switching off the machine, open the door (START/PAUSE led starts blinking) (be ware of HOT steam!) and place the crockery inside the dishwasher. Press the START/PAUSE button and close the door within 4 sec., the cycle will resume from the point at which it was interrupted.

ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power cut, the cycle stops. Press the START/PAUSE button and close the door within 4 sec., the cycle will resume from the point at which it was interrupted.

ADVICE AND TIPS

TIPS
Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand under running water. Arrange the crockery so that it is held in place firmly and does not tip over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing the water to reach every surface and flow freely. Warning: lids, handles, trays and frying pans do not prevent the sprayer arms from rotating. Place any small items in the cutlery basket. Very soiled dishes and pans should be placed in the lower basket because in this sector the water sprays are stronger and allow a higher washing performance. After loading the appliance, make sure that the sprayer arms can rotate freely.
UNSUITABLE CROCKERY

• Wooden crockery and cutlery.
• Delicately decorated glasses, artistic handicrafts and antique crockery. Their decorations are not resistant.
• Parts in synthetic material which do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
  The colours of glass decorations and aluminum/silver pieces can change and fade during the washing process. Some types of glass (e.g. crystal objects) can become opaque after a number of wash cycles too.

DAMAGE TO GLASS AND CROCKERY

• Only use glasses and porcelain guaranteed by the manufacturer as dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the wash cycle is over.

TIPS ON ENERGY SAVING

• When the household dishwasher is used according to the manufacturer’s instructions, washing tableware in a dishwasher usually consumes less energy and water than hand dishwashing.
• In order to maximize dishwasher efficiency, it is recommended to initiate the wash cycle once the dishwasher is fully loaded. Loading the household dishwasher up to the capacity indicated by the manufacturer will contribute to energy and water savings. Information on the correct loading of tableware can be found in the Loading chapter. In case of partial loading, it is recommended to use dedicated wash options if available (Half load/ Zone Wash, Multi-Zone), filling up only selected racks. Incorrect loading or overloading the dishwasher may increase resources usage (such as water, energy and time, as well as increasing noise level), reducing cleaning and drying performance.
• Manual pre-rinsing of tableware items leads to increased water and energy consumption and is not recommended.

HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher please run a high-temperature program at least one a month. Use a teaspoon of detergent and run it without loading to clean your appliance.

CARE AND MAINTENANCE

CLEANING THE FILTER ASSEMBLY
Regularly clean the filter assembly so that the filters do not clog and that the wastewater flows away correctly. Using a dishwasher with clogged filters or foreign objects inside filtration system or spray arms may cause unit malfunction resulting in lose of performance, noisy work or higher resources usage. The filter assembly consists of three filters that remove food residues from the washing water and then recirculate the water.
The dishwasher must not be used without filters or if the filter is loose. At least once per month or after each 30 cycles, check the filter assembly and if necessary clean it thoroughly under running water, using a non-metallic brush and following the instructions below:

1. 1. Turn the cylindrical filter A in an anti-clockwise direction and pull it out (Fig 1).
2. Remove cup filter B by exerting a slight pressure on the side flaps (Fig 2).
3. Slide-out the stainless-steel plate filter C (Fig 3).
4. In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds etc.) please remove them carefully.
5. Inspect the trap and remove any food residues. NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).

After cleaning the filters, re-place the filter assembly and fix it in position correctly; this is essential for maintaining the efficient operation of the dishwasher.

CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended period of time, let the water run to make sure it is clear and free of impurities before performing the necessary connections. If this precaution is not taken, the water inlet could become blocked and damage the dishwasher.

CLEANING THE SPRAY ARMS On occasions, food residue may become encrusted onto the spray arms and block the holes used to spray the water. It is therefore recommended that you check the arms from time to time and clean them with a small non-metallic brush. To remove the upper spray arm, turn the plastic locking ring in an anti-clockwise direction. The spray arm should be replaced so that the side with the greater number of holes is facing upwards.
The lower spray arm may be removed by pulling it upwards.

WATER SOFTENING SYSTEM
Water softener automatically reduces water hardness, consequently preventing scale buildup on the heater, contributing also to better cleaning efficiency. This system regenerates itself with salt, therefore it is required to refill the salt containers when empty. Frequency of regeneration depends on water hardness level setting – regeneration takes place once per 6 Eco cycles with water hardness level set to 3. The regeneration process starts in the final rinse and finishes in the drying phase, before cycle ends.

• Single regeneration consumes ~3.5L of water;
• Takes up to 5 additional minutes for the cycle;
• Consumes below 0.005kWh of energy.

TROUBLESHOOTING

 Salt

indicator is lit

| Salt reservoir is empty. (After refill the salt indica- tor may remain lit for several wash cycles).| Refill reservoir with salt (for more information – see page 13). Adjust water hardness – see table, page 13.
 Rinse aid indicator is lit| Rinse aid dispenser is empty. (After refill the rinse aid indicator may remain lit for several wash cycles).| Refill dispenser with rinse aid (for more information – see page 14).

The dishwasher won’t start or does not respond to commands.

| The appliance has not been plugged in properly.| Insert the plug into the socket.
Power outage.| For safety reasons, dishwasher will not re-start automatically when power returns.  Open dishwasher door, press START/PAUSE button and close the door within 4 seconds.
The dishwasher door is not closed.| Vigorously push the door until you hear the “click”.
Cycle is interupted by door opening for more than 4 seconds.| Press START/PAUSE and close the door within 4 seconds.
It does not respond to commands.

Display shows: 9 or 12 and On/Off LED is blin- king rapidly

| Switch off the appliance by pressing the ON/OFF button, switch it back on after approxi- mately one minute and restart the program. If problem persists, unplug the appliance for 1 minute, then plug it back in.
The dishwasher won’t drain.

Display shows:

3 and On/Off LED is blinking rapidly

| The wash cycle has not finished yet.| Wait until the wash cycle finishes.
The drain hose is bent.| Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked.| Clean the sink drain pipe.
The filter is clogged up with food residues.| Clean the filter (see CLEANING THE FILTER ASSEMBLY).

The dishwasher makes excessive noise.

| The dishes are rattling against each| Position the crockery correctly (see LOADING THE RACKS).

An excessive amount of foam has been produced.

| The detergent has not been measured out correctly or it is not suitable for use

in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart the current cycle by switching OFF the dishwasher, then switch it on again, select a new program, press START/PAUSE and close the door within 4 seconds. Please do not add any detergent.

The dishes are not clean.

| The crockery has not been arranged properly.| Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being hinde- red by the dishes.| Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle.| Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been produced.| The detergent has not been measured out correctly or it is not suitable for use in dishwa- shers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has not been shut correctly.| Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.| Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt.| Fill the salt reservoir (see FILLING THE SALT RESERVOIR).

The dishwasher does not fill the water.

Display shows: H, 6 and On/Off LED is blinking rapidly

| No water in the water supply or the tap is closed.| Make sure there is water in the water supply or the tap running.
The inlet hose is bent.| Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher and reboot.
The sieve in the water inlet hose is clogged; it is necessary to clean it| After having carried out the verification and cleaning, turn off and turn on the dishwa- sher and restart a new program.
Dishwasher finishes the cycle prema- turely.

Display shows: 15 and On/Off LED is blinking rapidly

| ****

Drain hose positioned too low or siphoning into home sewage system.

| ****

Check if end of drain hose is placed at correct height (see INSTALLATION).Check for si- phoning into home sewage system, install air admittance valve if necessary.

Air in water supply.| Check water supply for leaks or other issues letting air inside.

In case your dishwasher doesn’t work properly, check if the problem can be solved by going through the following list. For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet. Policy and standard documentation and additional product information can be found by:

• Visiting our website www.blaupunkt-einbaugeraete.com
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-sales Service, please state the codes provided on your product‘s identification plate.

The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu (available only on certain models).

SAFETY INSTRUCTIONS

IMPORTANT TO BE READ AND OBSERVED Before using the appliance, read these safety instructions. Keep them nearby for future reference. These instructions and the appliance itself provide important safety warnings, to be observed at all times. The manufacturer declines any liability for failure to observe these safety instructions, for inappropriate use of the appliance or incorrect setting of controls. Very young children (0-3 years) should be kept away from the appliance. Young children (3-8 years) should be kept away from the appliance unless continuously supervised. Children from 8 years old and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge can use this appliance only if they are supervised or have been given instructions on safe use and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be carried out by children without supervision.

PERMITTED USE
CAUTION: the appliance is not intended to be operated by means of an external switching device, such as a timer, or a separate remote-controlled system. This appliance is intended to be used in household and similar applications such as: staff kitchen areas in shops, offices and other working environments; farm houses; by clients in hotels, motels, bed & breakfast and other residential environments. The maximum number of place settings is shown in the product sheet. The door should not be left in the open position – risk of tripping. The open appliance door can only support the weight of the loaded rack when pulled out. Do not rest objects on the door or sit or stand on it.
WARNING: Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with the skin and eyes and keep children away from the dishwasher when the door is open. Check that the detergent receptacle is empty after completion of the wash cycle.

WARNING: Knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position – the risk of cuts. This appliance is not for professional use. Do not use the appliance outdoors. Do not store explosive or flammable substances (e.g. gasoline or aerosol cans) inside or near the appliance – risk of fire. The appliance must be used only to wash domestic dishes in accordance with the instructions in this manual. The water in the appliance is not potable. Use only detergent and rinse additives designed for an automatic dishwasher. When adding salt to the water softener, run one cycle immediately to avoid corrosion damage to internal parts. Store the detergent, rinse aid and salt out of reach of children. Shut off the water supply and unplug or disconnect the power before servicing and maintenance. Disconnect the appliance in the event of any malfunction.

INSTALLATION
The appliance must be handled and installed by two or more persons – the risk of injury. Use protective gloves to unpack and install – risk of cuts. Connect the dishwasher to the water mains using only new hose-sets. The old hose sets should not be reused. All hoses must be securely clamped to prevent them coming loose during operation. All local waterboard regulations must be complied with. Water supply pressure 0.05 – 1.0 MPa. The appliance must be placed against the wall or built into furniture to limit access to its rear side. For dishwashers having ventilation openings in the base, the openings must not be obstructed by a carpet.
Installation, including water supply (if any) and electrical connections, and repairs must be carried out by a qualified technician. Do not repair or replace any part of the appliance unless specifically stated in the user manual. Keep children away from the installation site. After unpacking the appliance, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service. Once installed, packaging waste (plastic, styrofoam parts etc.) must be stored out of reach of children – risk of suffocation. The appliance must be disconnected from the power supply before any installation operation – risk of electrical shock. During installation, make sure the appliance does not damage the power cable – risk of fire or electrical shock. Only activate the appliance when the installation has been completed.If installing the dishwasher at the end of a row of units makes the side panel accessible, the hinge area must be covered to avoid risk of injury. The inlet water temperature depends on the dishwasher model. If the installed inlet hose is marked „25°C Max”, the maximum allowed water temperature is 25°C. For all other models, the maximum allowed water temperature is 60°C. Do not cut hoses and, in the case of appliances fitted with a water stop system, do not immerse the plastic casing containing the inlet hose in water. If hoses are not long enough, contact your local dealer. Make sure the inlet and drain hoses are kink-free and are not crushed. Before using the appliance for the first time, check the water inlet and drain hose for leaks. Make sure that the four feet are stable and resting on the floor, adjust them as required, and check that the dishwasher is perfectly leveled using a spirit level.

ELECTRICAL WARNINGS
The rating plate is on the edge of the dishwasher door (visible when the door is open). It must be possible to disconnect the appliance from the power supply by unplugging it if plug is accessible, or by a multi-pole switch installed upstream of the socket and the appliance must be earthed, in conformity with national electrical safety standards. Do not use extension leads, multiple sockets or adapters. The electrical components must not be accessible to the user after installation. Do not use the appliance when you are wet or barefoot. Do not operate this appliance if it has a damaged power cable or plug, if it is not working properly, or if it has been damaged or dropped. If the supply cord is damaged, it must be replaced with an identical one by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard – risk of electrical shock.
If the fitted plug is not suitable for your socket outlet, contact a qualified technician. Do not pull the power supply cable. Do not immerse the mains cord or plug in water. Keep the cord away from hot surfaces.

CLEANING AND MAINTENANCE

WARNING: Ensure that the appliance is switched off and disconnected from the power supply before performing any maintenance operation. To avoid risk of personal injury use protective gloves (risk of laceration) and safety shoes (risk of contusion); be sure to handle by two persons (reduce load); never use steam cleaning equipment (risk of electric shock). Non-professional repairs not authorized by the manufacturer could result in a risk to health and safety, for which the manufacturer cannot be held liable. Any defect or damage caused from non-professional repairs or maintenance will not be covered by the guarantee, the terms of which are outlined in the document delivered with the unit.

DISPOSAL OF PACKAGING MATERIALS The packaging material is 100% recyclable and is marked with the recycle symbol. The various parts of the packaging must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

DISPOSAL OF HOUSEHOLD APPLIANCES This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. For further information on the treatment, recovery and recycling of household electrical appliances, contact your local authority, the collection service for household waste or the store where you purchased the appliance. This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent negative consequences for the environment and human health. The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection center for the recycling of electrical and electronic equipment.

ENERGY-SAVING TIPS
ECO program is suitable to clean normally soiled tableware, that for this use, it is the most efficient program in terms of its combined energy and water consumption, and that it is used to assess compliance with the EU Ecodesign legislation. Loading the household dishwasher up to the capacity indicated by the manufacturer will contribute to energy and water savings. The manual pre- rinsing of tableware items leads to increased water and energy consumption and is not recommended. Washing tableware in a household dishwasher usually consumes less energy and water in the use phase than hand dishwashing when the household dishwasher is used according to the manufacturer’s instructions.

You can download the Safety Instructions and the Instruction Manual, by visiting our website www.blaupunkt-einbaugeraete.com

References

• www
• Blaupunkt Einbaugeräte: Blaupunkt

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>