Maisto 82521 Radio Control Vehicles Instruction Manual

: June 6, 2024
: Maisto

Table of Contents

Maisto 82521 Radio Control Vehicles Instruction Manual
Maisto Radio Control Vehicles
Battery Requirement:
How to play: (Refer to Diagram 3 & 4)
Performance Tips:
Battery use:
Disposal of batteries
FCC Label Compliance Statement:
ASS-21 O Compliance Statement:
Troubleshooting:
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Maisto 82521 Radio Control Vehicles Instruction Manual

Maisto Radio Control Vehicles

Please keep this owner’s instruction manual for future reference. It contains important information. We reserve the right to improve/revise the product specifications without notice.

Class 1 LED Product

Contents:
Vehicle x 1
Transmitter x 1
Owner’s Instruction Manual x 1

Battery Requirement:

Vehicle: 4 x 1.SV “AAA” LR03/R03 Batteries.
Transmitter: 2 x 1.5V “AAA” LR03/R03 Batteries.

Battery installation tor the Transmitter(Refer to Diagram 1)

Use a screwdriver to loosen the screw on the battery cover and to open the battery cover. (Screwdriver is not included).
install 2 new 1.5V “AAA” LR03/R03 batteries with correct polarity(+/-) as shown inside the battery compartment.
Install the battery cover and then tighten the screw on the battery cover.

Battery installation for the Vehicle: (Refer to Diagram 2)

Set the “power switch” on the vehicle to the OFF position.
Use a screwdriver to loosen the screw on the battery cover and to open the battery cover. (Screwdriver is not included).
Install 4 new 1.5V “AAA” LR03/R03 batteries with correct polarity(+/-) as shown inside the battery compartment.
Install the battery cover and then tighten the screw on the battery cover.

Maisto 82521 Radio Control Vehicles Instruction Manual
Fig4

How to play: (Refer to Diagram 3 & 4)

Set the “Power Switch” on the controller and vehicle to ON position, the “Power LED” ‘—- on the controller will flash less than 3 seconds then stay on, meaning the automatic frequency matching between the controller and the vehicle is completed.
if the “Power LED” of the controller flash for more than 3 seconds, switch off both the vehicle and controller, then turn them on again.
Pull the trigger in the transmitter to drive the vehicle forward. Push the trigger in the transmitter to drive the vehicle backward.
Pull or push the trigger in the transmitter and turn the steering wheel to control the vehicle turn to left or right.
Turn the steering wheel to the left or right to control the vehicle spin 360°.
Try different combinations of the trigger and steering wheel to perform different sideways drifting stunt actions.
The vehicle will get into self-protection mode and out of control if keep driving spin 360° for a long time, switching off both the vehicle and controller, then turning them on again can resume play.
The vehicle will be out of control when the batteries have run out of power, then need to replace with new batteries.
Turn the switch of the controller and vehicle to the OFF position when not in play.

Performance Tips:

Do not drive the vehicle on grass, sand or go through water.
Do not drive the vehicle in windy or rainy weather.
Do not drive the vehicle into any hard object.
Keep fingers, hair, and loose clothing away from the vehicle.
The operating range can be affected by a variety of factors:
Weak transmitter or vehicle batteries.
1nterierence from other items that emit radio frequency signals such as another RIC item on the same frequency, CB radios, cordless phones, high voltage transmitters, etc.
Outdoor usage is recommended in order to get optimal control range.

Battery use:

Alkaline batteries are recommended.
Only batteries of the same or equivalent type as recommended are to be used.
Do not mix alkaline, standard, or rechargeable batteries.
Do not mix old and new batteries or different types of batteries.
Non-rechargeable batteries are not to be charged.
Rechargeable batteries are only to be charged under adult supervision.
Rechargeable batteries are to be removed from the product before they are charged.
Be sure to insert batteries with correct polarities and always follow the battery manufacturer’s instructions.
Remove all batteries from the product when not in use for a long period of time.
Exhausted batteries are to be removed from the product.
The supply terminals are not to be short-circuited.
Dispose of batteries properly. Do not dispose of batteries in a fire – it may cause them to explode or leak causing injury or damage.
Battery change must only be made by adults.

Cautions

Do not attempt to disassemble the products.
Do not operate the vehicle with the same frequency as other players in the same location. This will interfere and cause the vehicle to lose control.
Make sure the batteries are installed with correct polarity(+/-) as shown inside the battery compartment.
Remove the package, take out all accessories and assemble the product before giving it to children to play with.

Disposal of batteries

Batteries should not be disposed of in household waste. As the consumer, you are legally obliged to return batteries containing harmful substances and all other used batteries. You can hand in your old batteries at public collection points in your area or wherever batteries are sold.

You will find these chemical abbreviations along with a crossed-out refuse bin on batteries containing harmful substances:

Pb = Battery contains lead
Cd= Battery contains cadmium
Hg= Battery contains mercury

FCC Label Compliance Statement:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radiofTV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ASS-21 O Compliance Statement:

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference;
This device must accept any interference, including interference that may cause undesired operation of the device.