teesa TSA5010 Smooth Touch Window Vacuum Cleaner Owner’s Manual

teesa TSA5010 Smooth Touch Window Vacuum Cleaner Owner’s Manual

Overview

1. Rubber lip
2. Suction nozzle
3. Suction nozzle lock button
4. Separator
5. Separator lock button
6. Base unit
7. Power button
8. Water tank
9. Handle
10. Water tank opening
11. Water tank plug
12. Charging socket

A. Sprayer
B. Water tank / Extension pipe
C. Connecting knob
D. Cover
E. Wiper head with cloth holder
F.  Cloth
G. Holder

Thank you for purchasing TEESA appliance. Please read this operation instruction carefully before use, and keep it for future use.
Distributor does not take responsibility for damages caused by inappropriate handling and use of the product.

SAFETY INSTRUCTIONS

In order to reduce the injuries or damages, follow basic safety precautions applied when using any electrical device, including the following:

1. Read this instruction manual carefully, even if you are familiar with the appliance. Keep the manual for future reference.
2.  Before connecting the device to power supply socket, make sure the voltage indicated on the appliance corresponds to the voltage in the power supply socket.
3. Product intended for household use only.
4. Do not insert any objects into the ventilation slots.
5. Do not direct the sprayer at the eyes.
6. Use the window vacuum cleaner for cleaning wet, smooth surfaces such as windows, mirrors and tiles.
7. Always point the sprayer at the surface to be cleaned.
8. Do not point the spray jet directly at equipment that contains electrical components, such as the insides of ovens.
9. Do not use the device on rough surfaces so as to avoid damage to the rubber lip.
10. Clean this device in accordance to instructions listed in “Cleaning and Maintenance” section.
11. ALWAYS turn off the device and disconnect it from the mains supply:
    • if it’s not operating correctly
    • if there’s an uncommon voice when using
    • before disassembling the device
    • before cleaning
    • when not in use
12. When you disconnect the power cord of the device, grasp and pull the plug, not the cord/cable.
13. Keep the device out of the reach of children. Do not leave children unsupervised with the product.
14. This appliance must not be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised by the person who is responsible for their safety.
15. Keep the device and its cord/cable away from heat, water, moisture, sharp edges and any other factor which may damage the appliance or its cord.
16. Do not place the appliance in water or any liquid; nor handle/use it with wet or moist hands.
17. Do not use the product for purposes different from displayed in this operating manual.
18. Do not leave the appliance unattended when it’s working.
19. Producer of this product is not responsible for damages caused by inappropriate handling and using of the device.
20. ALWAYS disconnect the product from the mains supply when it is not in use.
21. DO NOT use this device if the cord or the plug is damaged, or the appliance is broken.
22. Do not attempt to repair this appliance yourself. Only authorized and qualified personnel may repair this device. Never disassemble this device.
23. Do not use unauthorized accessories.
24. Make sure the power cord does not touch any hot or sharp elements.

ASSEMBLY

1. Attach the suction nozzle to the separator. Correct placement is signified by an audible click.
2. Then attach previously assembled parts to the base unit. Correct placement is signified by an audible click.

ACCESSORIES

1. Screw the cover (D) to one end of the water tank / extension pipe (B).
2. Use the connecting knob (C) to attach the water tanks / extension pipes (B) with each other.
3. Fill the water tank (B) with the selected window cleaning agent, water or TEESA cleaning supply.
4. Then attach the sprayer (A) to the water tank (B).
5. Finally, attach the wiper head (E) to the sprayer (A). Correct placement is signified by an audible click (optionally, you can put a cloth (F) on the cloth holder).

It is also possible to use the water tank / extension pipe (B) with the main unit.

• First, follow the steps from 1 to 4.
• Attach the holder (G) to the device’s handle and then clamp it.
• Attach the device to the sprayer (A) in such a way that you hear a click.

BEFORE FIRST USE

Prior to first use, please fully charge the battery.

Charging:

1. Make sure the device is turned off.
2. Make sure the device is placed:
   • on flat surface,
   • in a place with easy access to the power supply socket.
3. Connect one end of the charger into device’s charging port.
4. Connect the other end into the power supply socket. The device will issue a voice prompt.
5. During charging, red LED is on.
6. When charging is complete the device issues a voice prompt and blue LED is on.
7. When charging is complete disconnect the charger from the device and power supply socket.

Notes:

• Use only the included charger to charge the battery.
• Fully charge the battery after each use and store the device fully charged.

OPERATION

1. Apply selected window cleaning agent or water on the surface to be cleaned and clean it.
   Note:

   • To clean the selected surface you can use the sprayer with the attached wiper head. First, make sure that all of the parts were assembled correctly (see section Assembly – Accessories). Make sure the water tank is filled with the selected window cleaning agent or water. Then set the tip of the sprayer to the selected position: STREAM (foam) or SPRAY (water mist). Spray the surface to be cleaned. Finally, use the wiper head or the cloth to clean the surface.
   • To clean the surface you can use TEESA cleaning supply.

2. Turn on the window vacuum cleaner by pressing and holding Power button. Blue LED is on.

3. Place the rubber lip of the device on the surface to be cleaned and using light pressure pull it from top to bottom across the surface. Repeat this step until the surface is completely cleaned.
   Note: Avoid sucking in dust and dirt.

4. If the maximum fill level (marked “MAX”) of the water tank has been reached, the tank must be emptied.
   Note: It is recommended to empty the tank before the maximum water level has been reached. Otherwise, small amounts of water may get into the ventilation system and damage the device.

5.  To empty the water tank, firstly turn off the device by pressing Power button.

6. Then pull the water tank plug and pour dirty water into a container or sink.

7. Close the water tank opening with the plug afterwards.

8. When working with the device is finished, press Power button to turn it off. LED indicator goes off.
   Note: After each use remember to clean the device (see section “Cleaning and maintenance” and fully charge it (see section “Before first use”).

CLEANING AND MAINTENANCE

CLEANING

• Prior to cleaning make sure the device is turned off.

• Remove the suction nozzle from the separator by pressing lock button.

• Then remove the separator by pressing separator lock buttons.

• Rinse the suction nozzle and separator under running water.

• Clean the base unit with soft, slightly damp cloth. Do not use any abrasives or chemical agents to clean it.
  CAUTION! Base unit contains electrical components. It is strictly forbidden to clean the base unit under running water or immerse it in water or any other liquid!

• Remove wiper head from the sprayer and rinse it under running water.

• Wash the cloth. It can be washed in a washing machine.

• After the water tanks are emptied, rinse them under running water.

• None of the parts of the device is suitable for cleaning in washing machine.

• After cleaning, leave the device to completely dry in an open space.

Important! Before each assembly make sure that all of the parts and accessories are completely dry!

STORING

• Before storing make sure the device is clean, dry, fully charged and the water tank is empty.
• Store the device in a dry, cool place out of the reach of children.
• Store the device in an up-right position.
• Make sure the device is not connected to the power mains while storing.

TECHNICAL DATA

Output: DC 5 V/ 1 A
Battery| 3,7 V; 2200 mAh
Battery charging time| up to 3 h
Battery running time| up to 40 min
Physical

parameters

| Weight| 0,78 kg
Dimensions| 12,5 x 28 x 33,8 cm
In set| Window vacuum cleaner
Accessories| Suction nozzle (28 cm)
Suction nozzle (17 cm)
Sprayer x1
Water tank / Extension pipe x2
Knobs x2
Wiper head with washer x1
Cloth x1
Holder x1
Charger
User’s manual

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or Its literature, indicates that It should not be disposed with other household wastes at the end of its working life. To prevent possible harm lo the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>