MNENPOYMNH IZ-6010 Espresso Maker Siena Instruction Manual

MNENPOYMNH IZ-6010 Espresso Maker Siena Instruction Manual

Introduction

Thank you for having chosen an appliance from the IZZY range.

Safety interlocks

Please read these instructions carefully before using the appliance and save them for future reference. Please keep the sales receipt for guarantee purposes (pls see below “Guarantee and Customer Service”) Any use which does not conform to the instructions will absolve IZZY from any liability.

• Make sure your electricity supply is the same as the one shown on the underside of the appliance.
• Always plug your device into an outlet that is earthed. Failure to comply with this requirement may result in electric shock and possible serious injury.
• Never leave the appliance unattended when it is operating.
• Close supervision is necessary when your appliance is being used near children or infirm people. Ensure that they do not play with the appliance.
• This appliance is not intended for use by people with reduced physical, sensory or mental capabilities, children or those with lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Switch off and unplug:
• Before filling with water
• Before cleaning
• After each use
• Allow the appliance to cool down completely before putting on or taking off parts and before cleaning and storing the appliance.
• Never use the appliance for any other use than indicated.
• The device is intended for indoor use. Do not use the device outdoors.
• The device is intended only for domestic use. Any other use will cancel the warranty.
• Always use the coffee maker on a secure, dry level surface.
• Do not operate or place the device or parts in places of high humidity or where it may get wet.
• Protect from steam. Handle the steam nozzle with care. Make sure the nozzle is away from the body parts. There is a risk of injury.
• Do not come into contact with steam or hot water coming out of the steam nozzle or water tank.
• Do not touch the hot parts of the appliance when it is operating (eg filter holder, steam nozzle, removable cup tray, water tank, etc.).
• Do not use the appliance without water in the water tank.
• Do not use sparkling water to fill the water tank.
• Make sure the water in the water tank is not less than “MIN” indication and does not exceed “MAX” indication.
• Do not use the appliance without the water tank and the detachable drip tray.
• Do not remove the filter holder when the appliance is in operation.
• Do not let the power cord of the appliance hang over the edge of a table or bench edge or where a child can grab it. Do not allow the power cord to touch any warm surface.
• Never use the cord to pull the plug out of the socket. Disconnect always by pulling on the plug.
• Do not leave the appliance in temperature below 0°C as the water in the water tank can become ice and cause damage to the appliance.
• Do not use the appliance at altitudes higher than 2,200m above sea level.
• Never leave the power cable wrapped during use. Unwind it completly.
• Never use highly corrosive or abstractive cleaning agents. Never use metal scouring pads for cleaning.
• Never let the power unit, cord or plug get wet.
• If the appliance does get wet, immediately remove the power cord from the wall outlet and do not put your hands in the water. Never run the wet appliance and contact one of the authorized BENRUBI service centers.
• Do not let the cord touch hot parts.
• Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.
•  Always make sure there is water in the tank before switching on.
• Do not move the appliance when it is in operation.
• Do not touch the appliance with wet or damp hands.
• Do not use an extension power cord.
• Check the power cord periodically for possible damages.
• If the power cord or the plug of the appliance have been damaged, do not use the appliance and contact an authorized BENRUBI Service Center.
• In case of a possible damage, do not attempt to repair the appliance by yourself. Please contact one of the authorized BENRUBI service centers.
• Any repair made by an unauthorized B ENRUBI Service Center CANCELS THE GUARANTEE.
• Any misuse of the device cancels the guarantee.
• Only use original spare parts.
• The appliance conforms to EU directive 2014/30/EU on Electromagnetic Compatibility, the 2014/35/EU Low Voltage Directive, the2011/65/EU RoHS Directive, the directive 2009/125/EC for eco-design and the EC regulation no. 1935/2004 on materials intended to contact with food.

SAVE THESE INSTRUCTIONS

Parts of the Appliance

1. ON/OFF button with indication light
2. Coffee button with indication light
3. Steam button with indication light
4. Cup preheat tray
5. Steam control knob
6. Water tank lid
7. Water tank 1.5L
8. Measuring spoon and tamper
9. Body
10. Steam/hot water nozzle
11. Detachable drip tray
12. Detachable rack
13. Filter holder handle
14. Drain filter hook
15. Filter holder
16. Double dose filter
17. Group for Nespresso®* capsule
18. Nespresso® capsule* holder

Τrademark of a third party, not connected to (NEW) H, BENRUBI & FILS S.A.

Before the First Use

1. Wash the parts of the appliance. See “Care and cleaning” section.
2. Run two full tanks of water (without coffee) through the coffee maker to clean it out. See

Preheating the espresso machine” section.

Note: There may be noise when the water is pumped the first time, it is normal, the appliance releases the air to the device. After a few seconds, the noise will stop.

If water does not run from the filter holder (16) during the first use, follow the steps below:

1. Place a cup on the detachable rack (12) and a cup under the steam nozzle (10) and plug in. Make sure the steam control knob (5) is in the “ ” position before plugging in the appliance.
2. Press the ON/OFF button (1) to prepare coffee. The indicator light will flash until the appliance warms up and is ready.
3. When the indicator light stops flashing, press the coffee button (2) to run water into the cup.
4. At the same time, turn the steam control knob (5) to the “max” position, and repeat until water starts to flow into the cup you have placed under the nozzle.
5. As soon as water starts to flow from the nozzle, turn the steam control knob (5) to the “  position. When the desired amount of water is run into the cup under the group, the appliance will stop automatically, and the indicator light will flash.
6. The device is ready for use.

Preheating the Espresso Machine]

To make a cup of good hot Espresso or Cappuccino, we recommend that you preheat the appliance before making coffee as well as the filter holder, filter and cup so that the coffee flavor is not affected by the cold parts of the appliance.

Make sure the steam control knob (5) is in the “ ” position before plugging in the appliance.

1. Remove the water tank (7) by pulling it upwards and filling it with water. Make sure the water in the water tank is not less than “MIN” and does not exceed “MAX” indication.

   • Use cold water. We recommend using filtered water as it reduces limescale and prolongs the life of your coffee maker. Never use ware or frizzy water.

2. Place the water tank (7) in place until it snaps firmly into the base of the appliance.

3. Remove the handle/filter holder (13) by turning counterclockwise and place the filter (16) without coffee.
   Note: Insert the filter tab into the notch of the filter holder and turn the filter to lock in its place.

4. Place the handle/filter holder (13) by turning clockwise. Ensure that the handle/filter holder snaps firmly to the “ ” position.

5. Place a cup on the detachable rack (12) and connect the plug into the socket.

6. Press the coffee ON/OFF button (1) to prepare the appliance. The indicator light will flash until the appliance is warm and is ready.

7. When the indication lights stop flashing, press the coffee button (2) to run water into the cup. The indication light will turn on.

8. When the desired amount of water is running, press again the coffee button (2). The appliance will stop, and the ON/OFF indication light will remain on.

9. When the warm-up process is complete, you can proceed to brewing coffee.

Note:

• There may be noise when the water is pumped the first time, it is normal, the appliance releases the air to the device. After about 20 seconds, the noise will stop.

Espresso Preparation

Make sure the steam control knob (5) is in the “ ” position before plugging in the appliance.

1. Preheat the Espresso Machine. See section “Preheating the espresso machine”.
2. Remove the handle/filter holder (13) by turning counterclockwise and place the desired coffee dose using the measuring spoon (8) and press the coffee on the filter with the back side of the spoon.
   • Never press the coffee too firmly as it will come out slowly and this will affect its color and flavor. If you press too lightly, the coffee will flow very quickly and will become light.
3. Place the handle/filter holder (13) by turning clockwise. Ensure that the handle/filter holder snaps firmly to the “ ” position.
4. Remove hot water from the cup and re-place the warm cup into the detachable rack (12).
5. If the ON/ FF indication light (1) is on and does not flash, press the coffee button (2).
6. When the desired amount of coffee runs, press again the coffee button (2). The appliance will stop, and the ON/OFF indication light will remain on.
7. When you are finished, press the ON/OFF button (1) and remove the plug  from the socket.
8. Remove the filter handle/filter holder (13) by turning counterclockwise and allow to cool before emptying the coffee filter.
9. Once the filter handle (13) and the filter (16) have cooled down, lift the drain filter hook (14) to snap to the end of the filter and drain coffee from the filter.
10. After each use, empty the water tank and wash the handle/filter holder and filter. See “Care and cleaning”.

Notes:

• Do not use very finely ground coffee as it may clog the filters.
• Do not leave the coffee maker unattended while it is operating.

Note:

• If the appliance remains on without operation, it will turn off automatically after 25 minutes.

Make sure the steam regulator (5) is in the “ ” position before plugging in the appliance.

1. Remove the water tank (7) by pulling it upwards and filling it with water. Make sure the water in the water tank is not less than “MIN” and does not exceed “MAX” indication.

   • Use cold water. We recommend using filtered water as it reduces limescale and prolongs the life of your coffee maker. Never use ware or frizzy water.

2. Place the water tank (7) in place until it snaps firmly into the base of the appliance.

3. Connect the plug into the socket. 20

4. Insert the capsule of your choice into the Nespresso®*(18) capsule holder (seep hoto) and close the cap

5. nsert the holder (18) into the group (17).
   Note: To insert the holder (18) into the group (17), make sure that the arrow on the lid is aligned with the group notch (17). Turn the capsule holder (18) to lock in its place.

6. Place the group (17) by turning clockwise. Ensure that it snaps firmly to the “ ” position.

7. Press the coffee ON/OFF button (1) to prepare the appliance. The indicator light will flash until the appliance is warmed up and ready.

8. When the indicator light stops flashing, press the coffee button (2) to pour coffee into the cup. The indicator light will turn on.

9. When the desired amount of coffee is running, press the coffee button (2) again. The appliance will stop and the ON/OFF indication light will remain on.

10. When you have finished the process, press the ON/OFF button (1) and remove the plug from the socket.

11. Remove the group (17) by turning counterclockwise and allow to cool before removing the capsule.

12. Once the group (17) and the capsule holder (18) have cooled, remove the capsule holder (18) by turning so that the arrow on the holder (18) lines up with the notch in the group (17). Open the holder lid and remove the capsule.

13. After each use, empty the water tank and wash the group (17) and the holder (18). See the “Cleaning and care” section.

Notes:

• Do not leave the coffee maker unattended while it is operating.
• If the appliance remains on without operation, it will turn off automatically after 25 minutes.

How to Make Froth Milk

Make sure the steam regulator (6) is in the “ ” position before plugging in the appliance.

1. Prepare the espresso as described in “Espresso Preparation” section.
2. Make sure there is enough water in the water tank (7) and that the steam control knob (5) is the “ ” position. Make sure the water in the water tank is not less than “MIN” and does not exceed “MAX” indication.
3. Press the steam button (3). The indicator light will blink until the appliance is warm and ready for steam preparation.
4. When the indicator light stops flashing, it is ready for use.
5. Add about 100ml of milk for each cup of cappuccino that you want to make in a metal jug.
   • For best results, it is recommended that you use cold whole milk. Do not use compacted milk.
   • The volume of milk can be increased up to 2 times, so you should choose a fairly wide and tall jug, diameter not less than 7.5cm.
6. Turn the steam/hot water pump (10) to the right and place the metal jug with the milk under the steam nozzle.
7. Immerse the steam nozzle about 2cm into the milk surface and turn the steam control knob (5) counterclockwise to start steam.
8. Move the jug cyclically and upwards and downwards.
9. When the procedure is complete, turn the steam control button (5) clockwise to the “ ” position.
10. Stir the froth with soft circular motions and tap the pot on the bench.
11. Put the froth in the cup with the espresso using a spoon. Sprinkle with cocoa powder or cinnamon if desired.
12. Clean the steam nozzle with a damp cloth or sponge immediately after each use with care not to burn.
13. Press the ON/OFF button (1) to turn off.
14. Remove the plug from the socket.

Notes:

• Never turn the steam control knob rapidly, as steam will accumulate in a very short time, increasing the risk of accidents.
• Never operate the steam/hot water pump (10) for more than 2 minutes at a time.
• Never allow the milk to reach boiling temperature to prevent the taste of  cappuccino.
• If you want to make over 1 cup of cappuccino, first prepare the coffees and then the milk froth.

Notes:

• After finishing the frothed milk, press the coffee button (2). If the coffee and steam indicator light flashes quickly, it means that the temperature of the appliance is too high, and the appliance must be switched off and rested for more than 5 minutes.
• If the appliance overheats, the coffee will get burnt and the filter will overflow.

Tips for a Great-Tasting Coffee

• A clean coffee maker is essential for making great-tasting coffee. Regularly clean the coffee maker as specified in the “Care and cleaning” section.
• Always use fresh, cold water in the coffee maker.
• Do not use very finely ground coffee as it may clog the filters.
• When buying ground coffee make sure it is suitable for espresso machines.
• Keep coffee in a cool and dry place. When you open the package of coffee, keep tightly closed in refrigerator to keep the freshness.
• For optimal effect, buy whole coffee beans and grind them just before the filtering process.
• Do not use the same coffee for the second time, as this would destroy its aroma.
• Not recommended reheating coffee. Coffee has the maximum aroma, immediately after preparation.
• Allow the coffee maker to cool down at least for 5 minutes before making coffee again. Otherwise burnt odor may occur in your espresso coffee.

Descaling

1. Buy a suitable descaler.
2. Descale the machine following the instructions on the package.
3. After descaling, run at least three full tanks of water (without coffee) through the coffee maker to clean it out.
4. Wash the parts. See “Care and cleaning” section.

Care and Cleaning

• Always switch off, unplug and allow to cool before cleaning the appliance.

• Don’t wash parts of the appliance in the dishwasher

• Clean all removable parts of the device after each use with warm soapy water.

• Clean the outer parts of the device with a soft, damp cloth.
  CAUTION: Do not immerse the coffee maker in water or any other liquid.

• Do not clean the inside of the water tank with a cloth while may cause remnants of the fabric fibers and clog the coffee maker.

• Do not clean with alcohol, or solvent cleanser.

Water tank / Filter holder / Capsule group:

• Wash the water tank and filter holder with water and dishwashing detergent, rinse thoroughly and allow them to dry thoroughly to avoid oxidation.
• Do not wash in the dishwasher.

Coffee filter / capsule holder:

• Wash and dry thoroughly after each use.
• After about 100 uses, thoroughly clean the coffee filter by following the procedure below: Remove the metal filter from the case. Clean the filters with hot water using a brush. Make sure all the filter holes are open, if coffee remains have remained in the filter holes, use a pin to remove them.
• Do not wash in the dishwasher.

Steam/Hot Water pump and nozzle:

• Before proceeding with cleaning, leave hot water to run from the nozzle. Then unplug the power cord and allow the appliance to cool down.
• Remove the steam nozzle by pulling it down and wash it thoroughly with soap and water. Ensure that the metal pipe is not clogged with milk residue. If necessary, clean the small steam outlet hole with a pin.
• Replace the steam nozzle in its correct position.
• Do not wash in the dishwasher.

Drip tray:

• Empty the drip tray frequently.
• Remove the detachable rack and drip tray, wash with water and detergent and dry thoroughly after each use.
• Do not wash in the dishwasher.

Basic Problem-Solving

correctly aligned.
The water level in the tank exceeds the MAX indication.| The water level in the container should be between MIN and MAX indication
Water leakage from the base of the coffee maker.| There is much water in the drip tra| Please clean the drip tray
The coffee maker malfunctions| Please contact an authorized BENRUBI service center.
Water leaks out of outer side of filter| There is some coffee powder on filter edge| Clean filter edge
Acid (vinegar) taste exists in espresso coffee.| The appliance has not been cleaned properly after descaling.| Please allow some water to run (without coffee) several times
The coffee powder is stored for a long time in a hot, wet place and has been turned o| Use fresh coffee or store the coffee in a cold and dry place. After opening the coffee pack, seal well and store it in the refrigerator to keep it fresh
The coffee maker does not work.| The plug of the appliance is not properly plugged in.| Plug the appliance into the socket properly. If the problem persists, contact one of the authorized BENRUBI service centers.
Steam does not create froth.| The container is too large or its shape is not suitable.| Use a high and narrow jug.

Technical Characteristics]

Model: Espresso maker Siena IZ-6010
Rated voltage / Frequency: 220-240V ̴50-60Hz
Power: 1100 W
Carafe capacity: 1.2 Liters
Pump pressure: 20 bar

Important Information for Correct Disposal of the Product in Accordance with EC Directive 2002/96/EC

At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources.

As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

Guarantee & Customer Service

• BENRUBI Company guarantees its products for any manufacturing defect or defective materials for a period of two (2) years from the date of purchase or delivery by presenting purchase receipt. If your product malfunctions or you find any defects, please revert to the retail location you have purchased it from or contact an authorized BENRUBI Service Centre. To find the nearest authorized BENRUBI Service Centre, visit our website www.benrubi.gr. It is in the discretion of BENRUBI Company to replace or repair the defective product.
• The warranty does not cover damages resulting from normal wear, breakage, scaling, improper installation or maintenance of the product, mishandling, abnormal working conditions, failure to implement the instructions, conversion or repair of the product by an unauthorized technician who does not belong to the BENRUBI Service Centers.

Also, the warranty does not cover the following indicative factors:

• Stains, discoloration or scratches.
• Burns due to exposure to heat or flame.
• Damage from thermal shock (sudden temperature change or change of voltage).

FOR MORE INFORMATION PLEASE CONTACT:

(NEW) H. BENRUBI & FILS SA

27 Aghiou Thoma str, GR15124, Maroussi – Athens, Tel./Customer Support: +30210 6156400
e-mail: benrubi-sda@benrubi.gr

References

• BENRUBI – Benrubi SA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>