THOMSON WEAR7208 Bluetooth In-Ear-Headphones Instruction Manual

: June 6, 2024
: THOMSON

**THOMSON WEAR7208 Bluetooth In-Ear-Headphones Instruction Manual

**

Controls and Displays

Product Overview

Earphones
Microphone
Status LEDs
Volume +, jump forward one title
On/off button, voice control, multi function button (MF)
Volume -, jump backward one title
Charging socket

Explanation of Warning Symbols and Notes

Warning

This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.

Note

This symbol is used to indicate additional information or important notes.

Package Contents

1x Bluetooth® stereo headset “WEAR 7208”
1x USB/Micro-USB charging cable
3 pairs of ear cushions (sizes S, M, L)
These operating instructions

Safety Notes

The product is intended for private, non-commercial use only.
Protect the product from dirt, moisture and overheating, and only use it in a dry environment.
Do not drop the product and do not expose it to any major shocks.
Do not operate the product outside the power limits given in the specifications.
Do not open the device or continue to operate it if it becomes damaged.
Since the battery is integrated and cannot be removed, you will need to dispose of the product as a whole. Do this in compliance with the legal requirements.
Dispose of packaging material immediately according to locally applicable regulations.
Do not modify the product in any way. Doing so voids the warranty

Warning – Battery

Only use suitable charging devices or USB connections for charging.
Asarule, do not charge devices or USB connections that are defective and do not try to repair them yourself.
Do not overcharge the product or allow the battery to completely discharge.
Avoid storing, charging or using batteries in extreme temperatures.
When stored over a long period of time, batteries should be charged regularly (at least every three months).

Warning – High volumes

Using this product limits your perception of ambient noise. For this reason, do not operate any vehicles or machines while using this product.
Always keep the volume at a reasonable level. Loud volumes, even over short periods, can cause hearing loss.

Getting Started

The headset is equipped with a rechargeable battery. The battery must be fully charged before using the device for the first time.
Ensure that the headset is switched off before charging it.
Begin charging by connecting the included USB charging cable to the charging socket (7) as well as to the USB connection of a PC/laptop.
Alternatively, you can charge the headset using a suitable USB charger. Please refer to the operating instructions for the USB charger used.
The display lights up constantly in red during the charging process.
It takes around 2-3 hours until the battery is completely charged.
Once the charging process is complete, the red light of the LED (3) turns to blue light.
Disconnect all cable and mains connections after use.

Operation

Switching the headset off/on

Press the MF button (5) until a voice says “Power ON” and the blue LED flashes.
To switch it off, press and hold the MF button (5) until a voice says “Power OFF” and the red LED flashes.

Note

The functions described in this section are only available for Bluetooth®-capable terminal devices.

Bluetooth® pairing

Note – Pairing

Make sure that your Bluetooth®-capable terminal device is on and Bluetooth® is activated.
Make sure that your Bluetooth®-capable terminal device is visible for other Bluetooth® devices.
For more information, please refer to the operating instructions of your terminal device.
The headset and the terminal device should not be any further than 1 metre away from each other. The smaller the distance, the better.
Switch the headset on using the MF button (5).
Press and hold the MF button (5) until the red and blue LEDs flash alternatingly and a voice says „Pairing“.
The headset is searching for a Bluetooth® connection.
Open the Bluetooth® settings on your terminal device and wait until Thomson WEAR 7208 appears in the list of Bluetooth® devices found.
Select Thomson WEAR 7208 and wait until the headset is listed as connected in the Bluetooth® settings on your terminal device.

Note – Bluetooth® password

Some terminal devices require a password in order to connect to another Bluetooth® device.

If your terminal device requests a password for connection with the headset, enter 0000.

Note

Once the connection has been established, a voice says, “Connected”.
If the connection attempt takes longer than 300 seconds to complete, it is cancelled and the LEDs go out.
In this case, repeat the steps listed previously under 5.1 Bluetooth® pairing.

Automatic Bluetooth® connection (after successful pairing)

Note

Make sure that your Bluetooth®-capable terminal device is on and Bluetooth® is activated.
Make sure that your Bluetooth®-capable terminal device is visible for other Bluetooth® devices.
For more information, please refer to the operating instructions of your terminal device.
Switch the headset on using the MF button (5). The blue LED begins to flash and the headset automatically connects with the last terminal device used.
A successful connection is signalized by the announcement (Connected).

Note

Once the connection has been established, a voice says, “Connected”.
If the connection attempt takes longer than 300 seconds to complete, it is cancelled and the LEDs go out. In this case, repeat the steps listed previously under 5.2.
It may be necessary to make settings on your terminal device to enable automatic connection with the paired headset.

Note – Connection impaired

After the headset and terminal device have been paired, a connection is established automatically. If the Bluetooth® connection is not established automatically, check the following:

Check the Bluetooth® settings of your terminal device to see whether Thomson WEAR 7208 is connected. If not, repeat the steps listed under 5.1. Bluetooth® pairing.
Check whether obstacles are impairing the range. If so, move the devices closer together.
The performance can also be affected by a weak battery.

Bluetooth® multipoint connection

This headset can be connected with two Bluetooth®-enabled terminal devices simultaneously.

First connect the headset with the first terminal device as described in 5.1.
Then disable Bluetooth® on that terminal device.
Next, connect the headset with the second terminal device as described in 5.1.
Activate Bluetooth® on the first terminal device once more. The headset now connects to that terminal device automatically.

Audio playback

Note

Note that the functions described under 5.3. and 5.4. are only possible with an active Bluetooth® connection.
Your terminal device must also support the individual functions.
For more information, please refer to the operating instructions of your terminal device.
Functions can still be controlled directly via the terminal device.
Set the volume on your terminal device to a low level.
Switch the headset on using the MF button (5). Upon successful connection, a voice says, “Connected”.
Start audio playback on the connected terminal device.
Press Volume + (4) to increase the volume. There is an announcement when the maximum volume is reached.
Press Volume – (6) to reduce the volume.
Press the MF button (5) to start or pause audio playback.
Press and hold Jump forward one title (4) to skip to the next title.
Press and hold Jump backward one title (6) to skip to the previous title.

Hands-free function

Press the MF button (5) once to answer an incoming call.
Press the MF button (5) for 1s or use your telephone to reject an incoming call.
During a call, press the MF button (5) once to end the call.
Press the MF button (5) twice to call the number of the last call.

Note – Call quality

To increase the call quality, make sure that you are near the headset with your mobile phone during the call.

Disconnecting the headset

Switch the headset off.
Disconnect the headset via the Bluetooth® settings on your terminal device.

Battery capacity

An announcement is made and the display flashes in red when the battery is low.
Charge the headset as described in 4. Getting Started.

Care and Maintenance

Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents. Make sure that water does not get into the product.

Warranty Disclaimer

Hama GmbH & Co. KG assumes no liability and provides no warranty for damage resulting from improper installation/ mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.

Service and Support

Please contact Hama Product Consulting if you have any questions about this product.
Hotline: +49 9091 502-115 (German/English)
Further support information can be found here: www.hama.com

Recycling Information

Note on environmental protection:

After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal system, the following applies: Electric and electronic devices as well as batteries must not be disposed of with household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an important contribution to protecting our environment.

Declaration of Conformity

Hereby, Hama GmbH & Co KG declares that the radio equipment type [00132640, 00132641, 00132642, 00132643] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.hama.com->00132640, 00132641, 00132642, 00132643 ->Downloads.

Frequency band(s): 2402MHz – 2480MHz
Maximum radio-frequency power transmitted: 3.5 mW EIRP

The Bluetooth ® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Hama GmbH & Co KG is under license. Other trademarks and trade names are those of their respective owners.

Thomson is a trademark of Technicolor (S.A.) or its affiliates used under license by HAMA GmbH & Co KG in 86652 Monheim/Germany

www.thomson-av-accessories.eu

Logo