PARKSIDE PAH 1300 B2 Demolition Hammer with Carry Case Instructions
- June 6, 2024
- PARKSIDE
Table of Contents
PARKSIDE PAH 1300 B2 Demolition Hammer with Carry Case
Introduction
Congratulations on the purchase of your new appliance. You have selected a
high-quality product. The operating instructions are part of this product.
They contain important information on safety, us-age and disposal. Before
using the product, please familiarise yourself with all operating and safety
instructions. Use the product only as described and for the specified areas of
application. Please also pass on these operating instructions to any future
owner.
Intended use
The demolition hammer PAH 1300 B2 is suitable for chiseling into concrete,
stone and plaster.
Any other usage of or modification to the appliance is deemed to be improper
and carries a significant risk of accidents.
The manufacturer accepts no responsibility for damage(s) attributable to
misuse.
The appliance is not intended for commercial use.
Depicted components
- Handle (rubberised grip)
- Locking switch
- ON/OFF switch
- Additional handle
- Knurled nut for additional handle
- Chisel adjustment ring
- Tool holder
- Locking collar
- Pointed chisel
- Flat chisel
- Grease
Package contents
- 1 demolition hammer PAH 1300 B2 1 additional handle (pre-assembled) 1 flat chisel
- 1 pointed chisel
- 1 carrying case
- 50 g grease
- 1 set of operating instructions
Technical data
- Nominal power 1300 W
- Rated voltage 230 V ∼, 50 Hz (alternating current)
- Stroke rate 3800 bpm
- Impact energy 15 Joules
- Tool fitting SDS MAX
- Protection class II / (double shielded)
Noise emission value
Noise measurement value determined in accordance with EN 60745. The A-rated
noise level of the power tool is typically as follows:
Chiseling
- Sound pressure level Uncertainty LpA = 88.8 dB (A)
- Sound power level Uncertainty K = 2.36 dB
- LWA = 102.8 dB (A) K = 2.36 dB
Total vibration value
Total vibration values (vector total of three directions) determined in accordance with EN 60745
Main handle
Chiseling ah(CHeq) = 16.7 m/s2, K = 1.5 m/s2
Auxiliary handle
Chiseling ah(CHeq) = 14.8 m/s2, K = 1.5 m/s2
NOTE
-
The vibration level specified in these instructions has been measured in accordance with a standardized measuring procedure and can be used to make equipment comparisons. The specified vibration emission value can also be used to make an initial exposure estimate.
WARNING! -
The vibration level varies in accordance with the use of the power tool and may be higher than the value specified in these instructions in some cases. Regular use of the electric tool in such a way may cause the user to underestimate the vibration. Try to keep the vibration loads as low as possible. Measures to reduce the vibration load are, e.g. wearing gloves and limiting the working time. Wherein all states of operation must be included (e.g. times when the power tool is switched off and times where the power tool is switched on but running without load).
General Power Tool Safety Warnings
WARNING!
- Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery- operated (cordless) power tool.
-
Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
-
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
-
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. -
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that can-not be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. -
Service
a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Appliance-specific safety instructions for hammers
- Wear hearing protection. The effect of noise can lead to hearing loss.
- Use the additional handles supplied with the appliance. Loss of control can lead to injuries.
- Hold the appliance by the insulated handles when you are carrying out work during which the deployed tool may come into contact with concealed power cables or its own power cable. Contact with a “live” wire may make ex-posed metal parts of the power tool “live” and could give the operator an electric shock.
- Wear a dust mask.
Installation
Additional handle
-
You can position the additional handle as you wish.
-
Undo the knurled nut .
-
Swing the additional handle around the appliance axis or 180° forward or backward into the desired position (see foldout page).
-
Retighten the knurled nut .
Fitting a tool -
The supplied grease is solely for greasing the tool holder .
-
Pull the locking sleeve backwards.
-
Before fitting a tool into the tool holder , grease it lightly.
-
Insert the tool with a rotating movement in the tool holder until it clicks into itself.
-
Release the locking sleeve . This locks the holder.
Check that the tool is properly locked by pulling it. The system has radial play because of the design.
Removing a tool -
Pull the locking sleeve backwards and pull the tool out of the tool holder .
Adjust chisel position -
You can adjust the flat chisel in optimal working position.
-
Place the flat chisel into the tool holder .
-
Push the chisel adjustment ring forward and turn with the chisel adjustment ring the flat chisel to the required position.
-
Release the chisel adjustment ring and turn it until it clicks.
Operation
Switching on and off
During operation, you can choose between instantaneous and continuous
operation.
Switching to instantaneous operation
-
Switching to instantaneous operation
Press the ON/OFF switch .
Switching off instantaneous operation -
Release the ON/OFF switch .
Switching to continuous operation -
Press the ON/OFF switch and lock it in this position with the locking switch .
Switching off continuous operation -
Press the ON/OFF switch and release it again.
Maintenance and cleaning
WARNING! RISK OF INJURY! Switch the appliance off and remove the power plug before starting any work on the appliance.
-
The appliance must always be kept clean, dry and free from oil or grease.
-
Use a soft, dry cloth to clean the housing.
-
Clean the tool holder regularly.
WARNING! -
If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.
Disposal
The packaging is made from environ-mentally friendly material and can be
disposed of at your local recycling plant.
Do not dispose of power tools in your normal domestic waste!
European Directive 2012/19/EU requires that worn-out power tools be collected
separately and recycled in an environ-mentally compatible manner.
Your local community or municipal authorities can provide information on how
to dispose of the appliance.
Dispose of the packaging in an environmentally friendly manner. Note the
labelling on the packaging and separate the packaging material components for
disposal if necessary. The packaging material is labelled with abbreviations
(a) and numbers (b) with the following meanings:
1–7: plastics, 20–22: paper and cardboard, 80–98: composites.
Your local community or municipal authorities can provide information on how
to dispose of the worn-out product.
The product is recyclable, subject to extended producer responsibility and is
collected separately.
warranty
Dear Customer,
This appliance has a 3-year warranty valid from the date of purchase. If this
product has any faults, you, the buyer, have certain statutory rights. Your
statutory rights are not restricted in any way by the warranty described
below.
Warranty conditions
The warranty period starts on the date of purchase. Please keep your receipt
in a safe place. This will be required as proof of purchase.
If any material or manufacturing fault occurs within three years of the date
of purchase of the product, we will either repair or replace the product for
you or refund the purchase price (at our discretion). This warranty service
requires that you present the defective appliance and the proof of purchase
(receipt) within the three-year warranty period, along with a brief written
description of the fault and of when it occurred.
If the defect is covered by the warranty, your product will either be repaired
or replaced by us. The repair or replacement of a product does not signify the
beginning of a new warranty period.
Warranty period and statutory claims for defects
The warranty period is not prolonged by repairs effected under the warranty.
This also applies to replaced and repaired components. Any damage and defects
present at the time of purchase must be reported immediately after unpacking.
Repairs carried out after expiry of the warranty period shall be subject to a
fee.
Scope of the warranty
- This appliance has been manufactured in accordance with strict quality guidelines and inspected meticulously prior to delivery.
- The warranty covers material faults or production faults. The warranty does not extend to product parts subject to normal wear and tear or to fragile parts which could be considered as consumable parts such as switches or parts made of glass.
- The warranty does not apply if the product has been damaged, improperly used or improper-ly maintained. The directions in the operating instructions for the product regarding proper use of the product are to be strictly followed. Uses and actions that are discouraged in the operating instructions or which are warned against must be avoided.
- This product is intended solely for private use and not for commercial purposes. The warranty shall be deemed void in cases of misuse or improper handling, use of force and modifications / repairs which have not been carried out by one of our authorized Service centers.
The warranty period does not apply to
- Normal reduction of the battery capacity over time
- Commercial use of the product
- Damage to or alteration of the product by the customer
- Non-compliance with safety and maintenance instructions, operating errors
- Damage caused by natural hazards
Warranty claim procedure
To ensure quick processing of your case, please observe the following
instructions:
- Please have the till receipt and the item number (e.g. IAN 12345) available as proof of purchase.
- You will find the item number on the type plate on the product, an engraving on the product, on the front page of the operating instructions (below left) or on the sticker on the rear or bottom of the product.
- If functional or other defects occur, please contact the service department listed either by telephone or by e-mail.
- You can return a defective product to us free of charge to the service address that will be pro-vided to you. Ensure that you enclose the proof of purchase (till receipt) and information about what the defect is and when it occurred.
You can download these instructions along with many other manuals, product videos and installation software at www.lidl- service.com.
Service
Service Great Britain
Tel.: 0800 404 7657
E-Mail: kompernass@lidl.co.uk
Service Ireland
Tel.: 1890 930 034
(0,08 EUR/Min., (peak))
(0,06 EUR/Min., (off peak)) E-Mail:
kompernass@lidl.ie
Importer
Please note that the following address is not the service address. Please use
the service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH BURGSTRASSE 21
44867 BOCHUM
GERMANY
www.kompernass.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>