6SPOTRGBW 6Spot RGBW Complete Pack-N-Go Lighting Solution
User Manual
1. Before You Begin
What Is Included
- 6SPOTRGBW
- Power cord
- Hanging bracket
- Quick Reference Guide
Unpacking Instructions
Carefully unpack the product immediately and check the container to make sure
all the parts are in the package and are in good condition.
Claims
If the box or the contents (the product and included accessories) appear
damaged from shipping, or show signs of mishandling, notify the carrier
immediately, not Chauvet. Failure to report damage to the carrier immediately
may invalidate your claim. In addition, keep the box and contents for
inspection.
For other issues, such as missing components or parts, damage not related to
shipping, or concealed damage, file a claim with Chauvet within 7 days of
delivery.
Text Conventions
Disclaimer
Chauvet believes that the information contained in this manual is accurate in
all respects. However, Chauvet assumes no responsibility and specifically
disclaims any and all liability to any party for any loss, damage or
disruption caused by any errors or omissions in this document, whether such
errors or omissions result from negligence, accident or any other cause.
Chauvet reserves the right to revise the content of this document without any
obligation to notify any person or company of such revision, however, Chauvet
has no obligation to make, and does not commit to make, any such revisions.
Download the latest version from
www.chauvetdj.com.
Intellectual Property
The works of authorship contained in this manual, including, but not limited
to, all design, text and images are owned by Chauvet.
© Copyright 2021 Chauvet & Sons, LLC. All rights reserved.
Electronically published by Chauvet in the United States of America.
CHAUVET, the Chauvet logo, and 6SPOT RGBW are registered trademarks or
trademarks of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the
United States and other countries. Other company and product names and logos
referred to herein may be trademarks of their respective companies.
Safety Notes
- This product is not intended for permanent installation.
- Always connect the product to a grounded circuit to avoid the risk of electrocution.
- Always disconnect the product from the power source before cleaning or replacing the fuse.
- Avoid direct eye exposure to the light source while the product is on.
- Make sure the power cord is not crimped or damaged.
- Never disconnect the product from power by pulling or tugging on the cord.
- If mounting the product overhead, always secure to a fastening device using a safety cable.
- Make sure there are no flammable materials close to the product when operating.
- Do not touch the product’s housing when operating because it may be very hot.
- The voltage of the outlet to which you are connecting this product must be within the range stated on the decal or rear panel of the product.
- The product is for indoor use only! (IP20) To prevent risk of fire or shock, do not expose the product to rain or moisture.
- Always install the product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent surfaces.
- Be sure that no ventilation slots on the product’s housing are blocked.
- Never connect the product to a dimmer or rheostat.
- Make sure to replace the fuse with another of the same type and rating.
- Never carry the product from the power cord or any moving part. Always use the handles.
- The maximum ambient temperature is 104 °F (40 °C). Do not operate this product at higher temperatures.
- In the event of a serious operating problem, stop using the product immediately.
- Do not open this product. It contains no user-serviceable parts.
- To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
Keep this User Manual for future use. If the product is sold to someone else,
be sure that they also receive this document.
2. Introduction
Product Overview
Product Dimensions
3. Setup
AC Power
The 6SPOT RGBW has an auto-ranging power supply and it can work with an input
voltage range of 100 to 240 VAC, 50/60 Hz.
To determine the product’s power requirements (circuit breaker, power outlet,
and wiring), use the current value listed on the label affixed to the
product’s back panel, or refer to the product’s specifications chart. The
listed current rating indicates the product’s average current draw under
normal conditions.
- Always connect the product to a protected circuit (a circuit breaker or fuse). Make sure the product has an appropriate electrical ground to avoid the risk of electrocution or fire.
- To eliminate unnecessary wear and improve its lifespan, during periods of non-use completely disconnect the product from power via breaker or by unplugging it.
Never connect the product to a rheostat (variable resistor) or dimmer circuit,
even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
Fuse Replacement
- Disconnect the product from power.
- Wedge the tip of a flat-head screwdriver into the slot of the fuse holder.
- Pry the fuse holder out of the housing.
- Remove the blown fuse from the holder and replace with a fuse of the exact same type and rating.
- Insert the fuse holder back in place and reconnect power.
Disconnect the product from the power outlet before replacing the fuse.
Power Linking
The product provides power linking via the outlet located in the back of the
product. See the diagram below for further explanation.
Power Linking Diagram
You can power link up to 11 6SPOT RGBW products on 120 VAC or up to 20 6SPOT
RGBW products on 230 VAC.
The power linking diagram corresponds to the North American version of the
product ONLY! If using the product in other markets, you must consult with the
local Chauvet distributor as power linking connectors and requirements may
differ in your country or region.
Mounting
Before mounting the product, read and follow the safety recommendations
indicated in the Safety Notes.
Orientation
The 6SPOT RGBW may be mounted in any position; however, make sure adequate
ventilation is provided around the product.
Rigging
- Before deciding on a location, always make sure there is easy access to the product for maintenance and programming.
- Make sure adequate ventilation is provided around the product.
- Make sure that the structure or surface onto which you are mounting the product can support the product’s weight. (see the Technical Specifications)
- When mounting the product overhead, always use a safety cable. Mount the product securely to a rigging point, whether an elevated platform or a truss.
- When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity.
- When power linking multiple products, mount the products close enough for power linking cables to reach.
- When mounting the product on the floor, make sure that the product and cables are away from people and vehicles.
Mounting Diagram
4. Operation
Control Panel Operation
To access the control panel functions, use the four buttons located underneath
the display. Please refer to the Product Overview to see the button locations
on the control panel.
Configuration (DMX)
The 6SPOT RGBW works with a DMX controller. Information about DMX is in the
CHAUVET DMX Primer, which is available from the Chauvet website
http://www.chauvetlighting.com/downloads/DMX_Primer_rev05_WO.pdf.
Starting Address and Personality
When selecting a starting DMX address, always consider the number of DMX
channels the selected DMX mode uses. If the starting address is set too high,
access to some of the product’s channels could be restricted.
The 6SPOT RGBW uses up to 8 DMX channels, which defines the highest
configurable address to 505. For information about the DMX protocol, download
the DMX Primer from www.chauvetdj.com.
To select the starting address and personality, do the following:
1. Press
