TRIPP LITE N785-H01-SCMM Hardened Gigabit Copper to Fiber Media Converter User Guide
- June 6, 2024
- Tripp Lite
Table of Contents
TRIPP LITE N785-H01-SCMM Hardened Gigabit Copper to Fiber Media Converter
Product Features
- Extends a Gigabit Ethernet connection over SC multimode fiber cable up to 500 meters (N785-H01-SCMM)
- Extends a Gigabit Ethernet connection over ST single-mode fiber cable up to 10 kilometers (N785-H01-SCSM)
- Extends a Gigabit Ethernet connection to an open SFP port (N785-H01-SFP)
- Hardened housing withstands high operating temperatures
- Provides ESD, RFI, and surge protection
- LEDs indicate Ethernet connection and fiber link status
- DIP switches control Local Loop Backtesting (LLB), Remote Loop Backtesting (RLB), Link Fault Signaling (LFS) and Reserve functions
- Link Fault Signaling (LFS) LED indicates when a cable has been severed or another cause for disruption has occurred
- Local LoopBack (LLB) tests the copper network connection
- Remote LoopBack (RLB) tests the fiber network connection
- Auto MDI/MDI-X functionality removes the need for crossover cabling
Package Contents
- N785-H01-SCMM or N785-H01-SCSM or N785-H01-SFP Media Converter
- External Power Supply with NEMA 1-15P Plug (Input: 100-240VAC, 50/60 Hz, 0.5A; Output: 12VDC, 1.5A)
- DIN Rail Kit
- Mounting Hardware
- L-Shaped Bracket
- SC Connector Cap
- Quick Start Guide
Optional Accessories
- N001-Series Cat5e Snagless Patch Cables
- N201-Series Cat6 Snagless Patch Cables
- N306-Series Duplex Multimode 62.5/125 Fiber Patch Cables (SC/SC)
- N356-Series Duplex Singlemode 9/125 Fiber Patch Cables (SC/SC)
- N286-Series Transceivers
- N785-CH12 12-Port Chassis for N784/N785 Media Converters
Installation
N785-H01-SCMM and N785-H01-SCSM
Notes:
- The following installation instructions refer to an installation in which two media converters are used. A single media converter can be used for a copper-to-fiber installation.
- The following installation instructions refer to the N785-H01-SCMM. Connections are the same for the N785-H01-SCSM, with only the specs being different. See the Specifications section in this manual for details on your media converter.
- To avoid damage due to Electrostatic Discharge (ESD), it is recommended you handle the product while wearing an ESD wrist grounding strap or by touching a conductive surface (such as metal) to discharge any potential ESD prior to handling the product.
Installation
-
Connect the RJ45 port on the media converter to your network with a user-supplied Cat5e/6 cable.
-
2 Connect the media converter to a second identical media converter using the appropriate type of fiber cable, making sure to connect the TX port on one unit to the RX port on the other.
Note: See the Product Features section in this manual to determine which type of fiber cable is supported by your media converter. -
Connect the RJ45 port on the second media converter to your network device (workstation, hub, switch, etc.) using a Cat5e/6 cable.
-
Connect the external power supplies that came with each media converter, and plug them into an AC power source.
N785-H01-SFP
Notes:
- The following installation instructions refer to an installation in which two media converters are used. A single media converter can be used for a copper-tofiber installation.
- The following installation instructions refer to the N785-H01-SFP. Connections are the same for all models, with only the specs being different. See the Specifications section in this manual for details on your media converter.
- To avoid damage due to Electrostatic Discharge (ESD), it is recommended you handle the product while wearing an ESD wrist grounding strap or by touching
conductive surface (such as metal) to discharge any potential ESD prior to handling the product.
- Connect the RJ45 port on the media converter to your network with a user-supplied Cat5e/6 cable.
- Connect a transceiver to the open SFP port on the media converter
- Connect fiber cabling matching the transceiver type to the transceiver’s port and to a second media converter with a matching transceiver.
- Connect the RJ45 port on the second media converter to your network device (workstation, hub, switch, etc.) using a Cat5e/6 cable.
- Connect the external power supplies that came with each media converter, and plug them into an AC power source.
LED Status Table
LED | Status | Description |
---|---|---|
PWR (Green) | On | The unit is powered on |
PWR (Green) | Off | The unit is not powered on |
ALM (Red) | On | LFS enabled and link fault occurred |
ALM (Red) | Off | LFS disabled or no link fault occurred |
RJ45 | ||
1000 (Green) | On | Copper connection up to 1000 Mbps |
1000 (Green) | Off | Copper connection speed at 10/100 Mbps or connection failed |
LNK/ACT (Green) | On | Copper port correctly linked |
LNK/ACT (Green) | Off | Copper port link failure |
Fiber | ||
1000 (Green) | On | Fiber connection up to 1000 Mbps |
1000 (Green) | Off | Fiber connection speed at 10/100 Mbps or connection failed |
LNK/ACT (Green) | On | Fiber port correctly linked and data is transmitting |
LNK/ACT (Green) | Off | Link failed, data is not transmitting |
LED Status Table
Link Fault Signaling (LFS)
The LFS LED will indicate when a cable has been severed or when some other
cause of disruption in service has occurred. The LFS function monitors both
copper and fiber segments for a total service report. Set DIP Switch 1 (LFS)
to ON for normal operational use and to OFF when installing cables or when
testing the network connection.
LoopBack Test
Each media converter features DIP switches to activate both local and remote
loopback diagnostic test functions. Use the Local LoopBack (LLB) function to
check if the copper segment is connected properly. Use the Remote LoopBack
(RLB) function to check if the fiber segment is connected properly.
Note: When enabling loopback testing in one segment of the connection the
other segment will be blocked until the loopback is disabled
Specifications
Specification | N785-H01-SCMM | N785-H01-SCSM | N785-H01-SFP |
---|---|---|---|
Optical Wavelength | 850 nm | 1310 nm | N/A |
Network Speed | 10/100/1000 Mbps (Gigabit) | ||
Mode | Multimode | Singlemode | SFP |
Transmission Distance | 500 m | 10 km | N/A |
Duplex Mode | Auto MDI/MDIX |
IEEE
Standards Supported
| IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX/FX IEEE 802.3ab 1000Base-T IEEE 802.3z 1000Base-SX/LX
IEEE 802.3 Auto-Negotiation
Power Consumption| 1.8W
Power Supply Input| 100-240VAC, 50/60 Hz, 0.5A
Power Supply Output| 12VDC, 1.5A
Operating Temperature| 14° to 140°F / -10° to 60°C
Storage Temperature| -40° to 185°F / -40° to 85°C
Relative Humidity| 5% to 95% RH, Non-Condensing
Unit Dimensions (H x W x D)| ****
23.4 x 73.8 x 109.2 mm / 0.92 x 2.9 x 4.3 in.
Warranty and Product Registration
Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable
instructions, to be free from original defects in material and workmanship for
a period of two (2) years from the date of initial purchase. If the product
should prove defective in material or workmanship within that period, Seller
will repair or replace the product, at its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM
ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER
THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED
BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET
FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND
CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an
implied warranty lasts, and some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitations or
exclusions may not apply to you. This warranty gives you specific legal
rights, and you may have other rights which vary from jurisdiction to
jurisdiction.)
WARNING: The individual user should take care to determine prior to use
whether this device is suitable, adequate or safe for the use intended. Since
individual applications are subject to great variation, the manufacturer makes
no representation or warranty as to the suitability or fitness of these
devices for any specific application.
Product Registration
Visit tripplite.com/warranty today to register your new Tripp Lite product.
You’ll be automatically entered into a drawing for a chance to win a FREE
Tripp Lite product!
No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
WEEE Compliance Information for Tripp Lite Customers and Recyclers
(European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite, they are entitled to:
- Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
- Send the new equipment back for recycling when this ultimately becomes waste
Use of this equipment in life support applications where failure of this
equipment can reasonably
be expected to cause the failure of the life support equipment or to
significantly affect its safety or effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject
to change without notice. Photos and illustrations may differ slightly from
actual products.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>