GLEDOPTO GL-C-001P 5-in-1 Smart LED Controller Max Instructions

GLEDOPTO GL-C-001P 5-in-1 Smart LED Controller Max

instruction

1. LED indicator
   Different color indicators correspond to different functions.

2. Reset
   Short press once to switch frequency; Short press twice to enter find and binding; Short press three times to enter touchlink; Short press four times to clear the zigbee network.

3. OPT
   Short press once to switch the function; Press and hold for more than 5 seconds to set the power-on status.

Common Anode
Constant Voltage

**FUNCTIONS OF DIFFERENT INDICATOR COLORS SHOWN AS FOLLOWING TABLE：(RGBCCT

RGBW >RGB >CCT >DIMMER >RGBCCT)**

NETWORK PARING

1. Pairing with Zigbee Hub
   Add the device to a zigbee network via coordinator or hub

   • Please ensure the device wasn’t be paired.
     Otherwise, please “RESET” the device according to the part Ⅱ “RESET”.

   • After STEP 1, there will be a pairing process about 90s
     Once times out, you need to repeat the

   • Open the zigbee App
     (hue or Amazon Alexa),add the device.

   • If the pairing done successfully after the above steps, the device will blink 3 times.

2. TouchLink to a Zigbee Remote Control / Touch Panel

   •  Please make sure the distance between the device and remote control/ touch panel less than 10cm;

   • Method 1: Please short press key “Reset” 3 times or power on/off the device 3 times to enter into “Touchlink Commissioning” mode, the device will blink 5 times.
     Reset
     Method 2 : Re-power on the device, Touchlink Commissioning will start after 15 seconds if it’s not added to a ZigBee network, 165 seconds timeout. Or start immediately if it’s already added to a network, 180 seconds timeout. Once timeout, repeat the operation.

   • Set the remote / touch panel to enter “Touchlink Commissioning”. Please refer to the manual of the corresponding remote / touch panel.

There shall be indication on the remote or touch panel for successful pairing, the device will blink 2 times. Now the device shall be controllable via the remote / touch panel.Note:

1. If the device & remote control in different Zigbee networks, each remote can link with one device.
2. If the device & remote control in the same Zigbee network, max 30 remotes can link with one device.
3. For the Philips Hue /Amazon Echo Plus, the device & remote control should in the same network before TouchLink.

Find and Bind Mode
*Note: Make sure that the device & remote are in the same network.

• Short press “Reset” button (or re-power on the device)for 2 times. The device will blink twice, and start “Find and Bind” mode to find the “Target Node”.
• Set the remote control/touch panel (target node) to enter the “Find and Bind” mode to search for “Bind Initiator”. Please refer to the manual of the corresponding remote / touch panel.
• Find and Bind” is completed, the remote / touch panel shall have indication. Now the device shall be remote control/touch panel controllable.

Pairing with 2.4GHz RF Remote Control / Touch Panel

1. The pairing will be timeout after 4 seconds when the device is powered on.
2. The pairing will be done successfully by pressing any zone “On” key of the 2.4G RF Remote or touch panel.
3. The indications from the device will blink 3 times.
   

RESET

RESET the Zigbee Network

1. Method 1: Delete the device on theAPP, the device will blink 3 times.
2. Method 2: Short press key “Reset” 4 times (Or re-power on the device 4 times) to unpair the network, the device will blink 3 times.

RESET the 2.4GHz RF Network
Method 1: Short press the Master “On” key 5 times within 4 seconds after the device powers on, the device will blink 3 times.
Method 2: Short press continuously 5 times the Zone “On” key the device being paired within 4 seconds after the device powered on, the device will blink 3 times.

FACTORY RESET:

The Factory Reset will be done successfully by long pressing “Reset” key more than 5 seconds (or re-power on the device 5 times or more). All configuration parameters will be reset after the device is reset or removed from the network, including ZigBee and 2.4G RF Network. The indicator will flash firstly 3 times in the color of the corresponding function selected, and turn into default White color (Default RGBCCT function) after flashing 4 times again.

WIRING DIAGRAM

RGBCCT: Under RGBCCT function, the RGBCCT strip can be connected to the device.

RGBW: Under RGBW function, the RGBW strip can be connected, without any connection to “N” terminal.

RGB: Under RGB function, the RGB strip can be connected, without any connection to “N” terminal.

CCT: Under CCT function, two pieces of CCT strips can be connected, without any connection to “N” terminal.

DIMMER: Under dimmer function, five pieces of single color strips can be connected.

POWER˜ON STATUS & FREQUENCY SETTINGS

Power-on Status Settings
Long press “opt” key for more than 5 seconds, the indicator will flash in light blue color and resume to previous color after “off” for 4 seconds to complete power-on status setting. The default power-on status is light on. The indicator flashing 3 times in light blue means light on under power-on status, flashing 4 times in light blue means light off under power-on status.

Frequency Settings
In order to be applicable to different power supplies, the frequency of device is selectable as 600Hz、800Hz、1000Hz、2000Hz、4000Hz、8000Hz with default frequency 1000HZ. Once short pressing “Reset” key, the frequency will switch into the next one. The indicator will flash in Pink color and resume to previous color after “off” for 2 seconds. The rule of indicator flashing times for different frequencies please refer to table.

SATURATION CONTROL FUNCTION VIA 2.4G RF REMOTE CONTROL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>