GLEDOPTO GL-RC-006Z RGB+CCT Remote Control User Manual
- June 5, 2024
- GLEDOPTO
Table of Contents
GL-RC-006Z RGB+CCT Remote Control
User Manual
RGB+CCT Remote Control (GL-RC-006Z)
This manual describes RGB+CCT remote control used for our RGB+CCT products
Remote control can control the LED lights in up to six different Zones, change
the color, dim/brighten the lights, and warm/cool white, different programs.ln
this manual, you will learn.
** Technical data:**
Size: 18x55x130mm
Material: PC Transmitting
Power: 6dB Modulation
Method: GFSK
Programs: 9 kinds
Power: 3V(AAA battery*2pcs)
Standby power: 15pA Working Temp:-20°C-60°C
Max control Range: 100 feet(30m)
RF Frequency: 2.4GHz
Warranty:2 Years
Battery Installation
Please take the remote control and carefully press the battery cover and push
it away in a downward motion. Install two AAA batteries, exactly match the
negative ( – ) pole of each battery to the largest spring. Don’t touch the
color ring when you install the batteries. Place the battery cover back and
install it tightly.
How to link & use
- Within 3 seconds after power-on, click the “on” button of the group to conduct code matching, and the LED light turns green, indicating successful code matching.
- Long press the “off” button of the remote control to enter the night light mode, and the brightness and color can still be adjusted at this time.
- long-press the small moon key to enter the 60 seconds delay shutdown state.
- Long press the M key to enter automatic mode.
How to unlink
- If the LED is still connected to the ZigBee gateway, long-press the “on” button on the remote control within 3 seconds after power-on or press the button 5 times continuously, and the light will flash 5 times in the current color;
- If the LED is not connected in the ZigBee gateway state, long-press the “on” button on the remote control within 3 seconds after power-on or press the button for S times continuously, then the LED light will be fully bright and flashing 5 times;
Mode description
Mode 1: Static warm light (warm light alone)
Mode 2: Static white light (cold light and warm light are equally bright)
Mode 3: Static cold light (cold light alone)
Mode 4: Static red light
Mode 5: Static green light Mode 6: Static blue light
Mode 7: RGB fade in fade out (Color fade in fade out from red to green, then
to blue, then to red, and so on, speed adjustable.)
Mode 8: RGB flash (Color flash from red to green, then to blue, then to red,
and so on, speed adjustable.)
Mode 9: Color breathing (In this mode, the brightness of the current color
will cycle from 100%-0%, then from 0%-100%. At the same time, you can switch
the color and have a cycle repeatedly. Pressing switch /mode button to exit
this mode.)
RGB+CCT Wall Switch (GL-W-0032)
This Panel Wall switch is designed by a delicate and fashionable tempered
glass panel, And we adopt a high precision Capacitive touch screen IC. Touch
Screen is very stable;2.4GHz high RF wireless control with long-distance
controlling, low power consumption, and high-speed transmitting rate. This
product widely works on our smart LED Lighting, LED Controller Smart panel
controller, etc.
Technical data:
Working Temperature: -20-60 °C
Input Voltage: 3V(2*AAA Battery)
Radio Frequency: 2400-2483.5MHz
Modulation Method: GFSK| Transmitting Power: 6dBm
Control Distance: 30m
Standby Power: 15uA
Size: 80x80x19mm
---|---
Battery Installation
Please take the wall switch and carefully press the battery cover and push it away in a downward motion install two AAA batteries, exactly matching the negative ( – ) pole of each battery to the largest spring. Place the battery cover back and install it tightly.
Warranty:
The warranty policy is valid if the product is used in accordance with the instructions and for its intended purpose. Cleaning and maintenance: To avoid scratching, the product should only be cleaned with a soft dry cloth. Do not use cleaning agents.
Disposal of your old product:
Your product is designed and manufactured with high-quality materials and
components, which can be recycled and reused. When this crossed-out wheeled
bin symbol is attached to a product it means the product is covered by the
Europen Directive 2011/65/EU.
Please find out for yourself about the local separate collection system for
electrical and electronic products.
Please act according to your local rules and do not dispose of your old
products with your normal household waste. The correct disposal of your old
product will help prevent potential negative consequences for the environment
and human health.
GL-RC-1-001
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>