GLEDOPTO GL-RC-006Z RGB CCT Remote Control Instruction Manual

GLEDOPTO GL-RC-006Z RGB CCT Remote Control

Features:

Gateways/hubs Gledopto zigbee products Directly work with: Via HUE, Hue Amazon gateway, echo can plus, work with SmartThings, google Tuya, home, all Conbee, other etc alexa devices

RGB+CCT Remote Control (GL-Rc–00&2)

This manual describes RGB+CCT remote control used for our RGB+CCT products Remote control can control the LED lights up to six different Zones, change the color, dim/brighten the lights, warm/cool white, different programs. In this manual, you will learn.

Battery Installation

Please take the remote control and carefully press the battery cover and push it away in a downward motion. Install two AAA batteries, exactly match the negative ( – ) pole of each battery to the largest spring. Don’t touch the color ring when you install the batteries. Place the battery cover back and install tightly.

How to link & use with remote control

1.  Within 3 seconds after power on, click the “on” button of the group to conduct code matching, and the LED light turns green, indicating successful code matching.
2.  Long press the “off” button of the remote control to enter the night light mode, and the brightness and color can still be adjusted at this time.
3.  long press the small moon key to enter the 60 seconds delay shutdown state.
4. Long press M key to enter automatic mode.

How to unlink

1.  If the LED is still connected to the Zig Bee gateway, long press the “on” button on the remote control within 3 seconds after power on or press the button for 5 times continuously, the light will flash for 3 times in the current color;
2. If the LED is not connected in the ZIGBEE gateway state, long press the “on” button on the remote control within 3 seconds after power on or press the button for 5 times continuously, then the LED light will be fully bright and flashing for 4 times;

Mode description

• Mode 1: Static warm light (warm light alone)
• Mode 2: Static white light (cold light and warm light are equally bright)
• Mode 3: Static cold light (cold light alone)
• Mode 4: Static red light
• Mode 5: Static green light
• Mode 6: Static blue light
• Mode 7: RGB blue, fade then in to fade red, out and so (Coloon r , fade speed in fade adjustable.) out from red to green, then to
• Mode 8: so RGB on, flash speed (Color adjustable.) flash from red to green, then to blue, then to red, and
• Mode g; switch\the colo rand hhave 8SJrA: repeatedly. iecPressing switch /mode 1c’lncle button to exit this mode.)

How to link & use with zigbee hub
These devices works with many Zig Bee Light Link/Zig Bee 3.0 Gateways like Philips Hue, Amazon Echo Plus or Smart Things.
Installation:

1. Turn off the Power.
2. Plug in the lamp.
3. Now you can connect it with the gateway.

Connection with Gateway:

1. Start the device searching on the Zig Bee Light Link/ZigBee 3.0Gateway, it could take some time.If the Gateway does not find the device, plug power off/on or make a reset.
2.  After finding the device, the light will turn green.then you can save it to the rooms/groups.
3.  Now you can use the device.

Reset:

1. Switch on your device.
2. Now switch off and on within 2 seconds.
3.  Repeat off/on five times.
4.  Reset is done when the device is switched on in the fifth time and the LED light will be fully bright and flashing for 4 times.

RGB+CCT Flood light

Picture

|

| |
---|---|---|---
Po w er| !OW| 30W| 60W
Size(mm)| 166x107x32| 226.Sx167x40| 309.5×267.5xl 82.2
NW(g)| 450| 950| 1800
GW(g)| 550| 1160| 2100
Driver| Customized| Mean Well| Mean Well
Luminous Flux| 650~850LM| 2100~2700LM| 4500~5000LM
Protection| JP65| JP65| JP65
Warranty| 3years| 3years| 3years
LED color| D ua l White And Colo r
Input voltage| AC100~240V
Color temperature| 2000K-6S00K
Working temp| -20- 60°(
Line length| 0.6m
Life span| 50,000h
Material| Alum inum, toug h enedglass
Compatible with Zigbee bridge

Picture

|

| |
---|---|---|---
Power| lO0W|  |
Size(mm)| 402x29Sx60|  |
NW(g)| 3600|  |
GW(g)| 4000|  |
Driver| Mean Well|  |
Luminous Flux| 7500-8000LM|  |
Protection| IP65|  |
Warranty| 3years|  |
LED color|
Input voltage|
Color temperature|
Working temp| -20- 60°(
Line length| 0.6m
Lifespan| 50,000h
Material| Aluminu m, toug h enedglass
Compatible with Zigbee bridge

RGB+CCT Garden lamp

12V lOW RGB+CCT Flood light

Parameter

• Power: 10W
• White LED Power: 1 OW
• Driver: Customized
• Luminous flux: 650~850LM
• Input Voltage: AC/DC 12V
• Color temperature: 2000~6S00K
• Material : Aluminum, toughened glass
• Model No.: GL-FL-00lP
• Size: 166Xl07X32mm
• Working temp:-20° C~60 ° C
• IP Rate: IP65

Installation

1.  Take the led flood light out of the packaging.
2.  Switch off the power at the wall or lamp switch before installation.
3. Replace the original flood light with the new Wireless Smart LED flood light.
4. Switch on the power, the led flood light will be on under nonTial circumstances.

Compability Chart

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>