GLEDOPTO GL-SD-001 Zigbee Triac AC Dimmer Instruction Manual

Zigbee Triac AC Dimmer
User Instruction

PRODUCT DESCRIPTION:

The Zigbee Triac AC Dimmer can be used for switching and dimming the brightness of lights loaded.

SPECIFICATION:

Size: 48x45x21mm
Model NO.: GL-SD-001
Input Voltage: 100~240VAC
Output Voltage: 100~240VAC
Output Current: 1.5 A Max
Protection rate: IP20
Radio Frequency: 2.4GHz
Operating Temperature: -20°C~60°C

COMPATIBLE LOAD TYPES:

| **** Dimmable LED lamps| **** 200W@220V 100W@110V

| **** Dimmable LED drivers| **** 200W@220V 100W@110V

| Incandescent lighting, HV Halogen lamps| 400W@220V 200W@110V

| Low voltage halogen lighting with electronic transformers| 200W@220V 100W@110V

Wiring Diagrams:

FUNCTION OF THE DEVICE:

Function of “RESET” key

1. MIN Brightness Setting
   Long press “Reset” key to set the “MIN brightness”. Once done, the brightness of the light can only be adjusted between the“MIN brightness” and 100% brightness.
   *Note:
   The dimming range of the dimmer is 1%-100%(brightness), but some lights may flicker while dim to 1%, thus the “MIN Brightness Setting” is needed.

2. RESET
   Short press for 5times to RESET the device.

Function of “LEVEL” key
① ON/OFF
Short press the “Level” key to turn on/off the device.
② DIMMER
Long press for adjusting the brightness of light.

Zigbee Clusters the device supports are as follows:
Input clusters

• 0x0000: Basic
• 0x0003: identify
• 0x0004: Groups
• 0x0005: Scenes
• 0x0006: on/off
• 0x0008: Level Control

Output clusters

• 0x0019: OTA

NETWORK PARING:

1. Pairing with Zigbee Hub
   Add the device to a zigbee network via coordinator or hub
   ① Please ensure the device wasn’t paired.
   Otherwise, please “RESET” the device according to the part Ⅶ “RESET”.

2. After STEP 1, there will be a pairing process about 90s. Once times out, you need to repeat the①.

3. Open the zigbee App (hue or Amazon Alexa), and add the device.

4. The device show itself on App and the light (connected to the device) will blink 4 times.

2. TouchLink to a Zigbee Remote Control / Touch Panel

1. Please make sure the distance between the device and remote control/ touch panel less than 10cm;

2. Method 1: Short press “Reset” button four 4 times to start “Touchlink Commissioning”.
   The device will flash 3 times to indicate successful enter the touch link pairing mode.
   Method 2: Re-power the device.
   a. If the device is not added to the zigbee network, “Touchlink Commissioning” will start after a 15s, 165s timeout.
   b. If the device is already added to the zigbee network, it will start “Touchlink Commissioning” immediately, 180s time out.
   Please repeat the operation once timeout.

3. Set the remote / touch panel to enter “Touchlink Commissioning”.
   please refer to the manual of the corresponding remote / touch panel.

4. The paring light will blink twice to indicate successfully connected.
   Now the device shall be zigbee remote / touch panel controllable.

*Note:

1. If the device & remote control are in different zigbee networks, each remote can link with one device.
2. If the device & remote control are in the same zigbee network, max of 30 remotes can link with one device.
3. For the Philips Hue /Amazon Echo Plus, the device & remote control shall be in the same network before TouchLink.

3. Find and Bind Mode
*Note: Make sure that the device & remote are in the same network.

1. Short press “Reset” button (or re-power the device) 3 times.
   The light (connected to the device) will blink twice, and start “Find and Bind” mode to find the “Target Node”.

2. Set the remote control/touch panel (target node) to enter the “Find and Bind” mode to search for “Bind Initiator”. Please refer to the manual of the corresponding remote / touch panel.

3.  “Find and Bind” is completed, and the remote / touch panel shall have an indication.
   Now the device shall be remote control/touch panel controllable.

4. Pairing with GLEDOPTO 2.4GHz RF Remote Control / Touch Panel

1.  battery power on the RF remote control/touch panel, within 3s, press zone “I” (of any group you want the light into) to start the pairing process.

2. the light (connected to the device) blinks 4 times to indicate successfully paring.

3. now the device shall be 2.4GHz remote control/touch panel controllable.

RESET

1. RESET the Zigbee Network

1. Method 1: Delete the device on theAPP.
   Method 2: Short press“RESET” key on the device 5 times.
   Method 3: Power cycle(on/off) the device 5 times.
   Method 2 :
   Method 3 :
   

2. The light (connected to the device) Flash 4 times, reset is done.

2. RESET the 2.4GHz RF Network

1. Method 1: power on the light, short press(within 4s) “MASTER I” button 5 times. (or the “I” button of Zone 1-6 which is pairing).

Method 2: power on the light, short press(within 4s) the “-” button 5 times. (or“-” button of Zone 1-4 which is paring).

2.  The light (connected to the device) shall flash for 4 times.

3. Reset is done.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>