B-TECH BT7007 Single Screen Digital Signage Kioske Installation Guide
- June 6, 2024
- B-TECH
Table of Contents
B-TECH BT7007 Single Screen Digital Signage Kioske Installation Guide
INSTALLATION SAFETY INSTRUCTIONS
CAUTION: This stand is intended for use only with the maximum weights indicated. Use with flat screens heavier than the maximum indicated may result in instability causing possible injury.
Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference. Please check carefully to make sure there are no missing or defective parts – defective parts must never be used. B-Tech International Design & Manufacturing Ltd, its distributors, and dealers are not liable or responsible for damage or injury caused by improper installation, improper use or failure to observe these safety instructions. In such cases, all guarantees will expire.
General
Great care must always be taken during installation as most AV equipment is of
a fragile nature, possibly heavy and easily damaged if dropped. If you do not
fully understand the instructions or are not sure how to install this product
safely, then please consult a professional for advice and/or to install this
product for you. Failure to mount this product correctly may cause serious
injury or death both during installation and at any time thereafter. Do not
mount any AV equipment that exceeds the specified weight limit of the product
you are installing. This weight limit will be clearly stated on each product
and its packaging and will vary from product to product.
Product location
Please pay careful attention to where this product is located, some locations
are not suitable for installation. For indoor use only. Install stand on level
ground. When verifying the stability of the structure, consider
the following external factors: The strength of the floor, exposure to sudden
and severe wind, and danger arising from contact with people and/or objects
(eg installations in passageways, emergency exits), if located in a public or
frequently populated area ensure that the product is out of the immediate
reach of people.
Fixing hardware
It is highly recommended that all fixing screws be used where supplied and
that the purpose of all other fixing hardware is fully understood. In some
cases more AV equipment fixing hardware will be supplied to accommodate
different models of equipment and set up configurations. The installer must be
satisfied that any supplied fixing hardware is suitable for each specific
installation. If any fixing screws or included hardware are deemed not
sufficient for a safe installation then please consult a professional or your
local hardware store.
Hazard limitation
When routing cables take advantage of any built-in cable management features
that the product might provide and ensure that all cables are tidy and secure.
Check to see that any moving aspect of the product can do so unhindered by any
cabling. Some products have moving parts and the potential to cause injury
through the crushing or trapping of fingers or other body parts. Particular
attention to the nature of moving parts is required especially when assembling
installing and adjusting during set up. Immediately after installations
double-check that the work done is safe and secure. Double-check all necessary
fixings are present and are of ample tightness. II is recommended that
periodic inspections of the product and its fixing points are made as
frequently as possible to ensure that safety is maintained. If in doubt
consult a professional AV installer or another suitably qualified person.
BT7007 PARTS LIST
| ITEM | PART NAME | QTY |
|---|---|---|
| 1 | BASE | 1 |
| 2 | KIOSK BODY | 1 |
| 3 | INTERFACE ARM | 2 |
| 4 | FRONT PANEL CONFIGURED | 1 |
| 5 | LOWER REAR PANEL | 1 |
| 6 | UPPER REAR PANEL | 1 |
| 7 | TOP GRILLE | 1 |
| 8 | M8 X 20mm SCREW | 4 |
| 9 | 5mm HEX KEY | 1 |
| 10 | KEY | 1 |
| 11 | M10 METAL WASHER | 6 |
| 12 | M10 SPRING WASHER | 6 |
| 13 | M10 NUT | 6 |
INSTALLATION INSTRUCTIONS
Remove Panels from Kiosk
- Remove item 7 from item 2 using item 10.
- Remove item 4, item 6, and then item 5 from item 2 by lifting the panels up and pulling away from the kiosk body.
Bolt Down To Floor – Optional
- Note: The kiosk can be used freestanding or bolted to the floor
- Pre-drill holes in floor and use suitable floor fixing fit (not supplied), fix item 1 to the floor.
Assemble Kiosk Body to Base
- Assemble item 2 (Kiosk Body) to item 1 (Base) using items 11, 12 & 13.
Attach Interface Arms to Screen
- Attach item 3 to the rear of the screen using item 8.
- Note: Ensure arms are positioned the correct way for portrait mounting the screen.
Mount Screen onto Rail
- Hook the screen onto the rail from the front side.
Return Front Panel and Adjust Screen
- Fix item 4 to item 2.
- Adjust the screen to fit with the cut-out on item 4.
- Once the screen has been positioned correctly, tighten the 2 security screws on the bottom of item 3 using item 9.
Fix Rear and Top Panels to Kiosk
- Attach item 5 and then item 6 to item 2.
- Fix item 7 to item 2, locking the top panel with item 10.
BT7007 PRODUCT DIMENSIONS
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>