Rosewill CFZ Series CFZ750 750W ATX Semi Modular Gaming Power Supply Installation Guide
- June 6, 2024
- Rosewill
Table of Contents
Rosewill CFZ Series CFZ750 750W ATX Semi-Modular Gaming Power Supply
INSTALLATION
If replacing an existing PSU in a system, you will first need to remove the old PSU. Please proceed as follows:
- Disconnect the AC power cord from your existing power supply unit.
- Disconnect the power supply from all the components in the PC, make sure that all the connectors are unplugged.
- Remove the four screws from the rear of the case that hold the old power supply to the chassis, and then remove the old power supply unit from case.
Installing the Power Supply:
- Make sure the 1/0 switch of the PSU is at off “O” position.
- Install the Power supply unit in the appropriated space in the PC case and secure it by screwing the four screws into the rear of the power supply.
- Connect the 20+4 pin main power cable to the motherboard 20+4 pin socket. The detachable 4 pin section of the connector can be separated to support a 20 pin connection or section together to support a 24 pin socket.
- Connect the 4+4 PIN (8 PIN) power cable to the mainboard. If your mainboard supports only 4 PIN jack, connect only the right side of the connector to the mainboard
- If you are using a graphics card with a 6 PIN/8 PIN connector, please connect the respective connector to the socket on the board. If your graphics card supports more than one socket, please connect the respective connector to the socket on board.
- Connect the SATA or Peripheral 4 PIN Molex connectors to the hard disk or SSDs or optical drive.
- Connect any others internal components that require power to the appropriate connector.
- Make sure all the cables are securely seated.
- Connect the AC power cord into the back of the power supply and switch on 1/0 switch at input “I” position.
- Your PSU is now connected and ready.
ELECTRONIC SPECIFICATIONS
Model No.
| AC Input| ****
DC Output
| ****
+3.3V
| ****
+5V
| ****
+12V
| ****
-12V
| ****
+5VSB
---|---|---|---|---|---|---|---
Voltage| Current
CFZ500
| ****
100V I 240V
| ****
8-4A
| Max Output Current| ****
20A
| ****
20A
| ****
38A
| ****
0.3A
| ****
2.5A
Max Combined Wattage| ****
100W
| ****
456W
| ****
3.6W
| ****
12.5W
Total Output| 500W
Model No.
| AC Input| ****
DC Output
| ****
+3.3V
| ****
+5V
| ****
+12V
| ****
-12V
| ****
+5VSB
---|---|---|---|---|---|---|---
Voltage| Current
CFZ600
| ****
100V I 240V
| ****
8-4A
| Max Output Current| ****
20A
| ****
20A
| ****
45A
| ****
0.3A
| ****
2.5A
Max Combined Wattage| ****
100W
| ****
540W
| ****
3.6W
| ****
12.5W
Total Output| 600W
Model No.
| AC Input| ****
DC Output
| ****
+3.3V
| ****
+5V
| ****
+12V
| ****
-12V
| ****
+5VSB
---|---|---|---|---|---|---|---
Voltage| Current
CFZ750
| ****
100V I 240V
| ****
10-5A
| Max Output Current| ****
20A
| ****
20A
| ****
62.5A
| ****
0.5A
| ****
2.5A
Max Combined Wattage| ****
100W
| ****
750W
| ****
6W
| ****
12.5W
Total Output| 750W
CONNECTORS
CFZSerles
Cable
| | | | | |
---|---|---|---|---|---|---
20+4 PIN
Motherboard Connector
| 4+4 PIN CPU
Connector
| 6+2 PIN PCI-E
Connector
| S-ATA
Connector
| 4 PIN
Molex Connector
| 4 PIN
Floppy
Connector
Fixed Cable| Modular Cable
CFZS00| | | 2| 4| 3|
CFZ600| | | 2| 6| 3|
CFZ750| | | 4| 6| 3|
PRODUCT FEATURES
- 80 Plus Bronze certified to dellver over 85% efflc:lency
- AlX 12VV2.3 ready supports EPS 12V2.92 and is backward compatible with AlX 12V 2.01
- Active Power Factor Correction (PFC) with PF value of 0.95
- Maximum Protection: Over-voltage protection. short circuit protection, overpower
- protection
- L..cng lasting, ultra-quiet 120 mm fan
- Crossfire and SLI support
- MTBF > 100,000 hours at 80% load, ambient temperature at 25″C
PACKAGE CONTENTS
- CFZ Power Supply Unit x1
- Quick User Gulde x 1
- AC Power Cord x1 80
- Cable Tie x3 PLUS’
- Mounting Ccrew x4
- Modular Cable Set x1
SAFETY & WARNING
- Due to the high voltage inside the power supply, do not attempt to remove the cover of power supply. The warranty will be void if the cover is removed.
- Do not insert any objects into the open ventilation or fan grill area of the power supply.
- Do not store the power supply in high humidity and high-temperature environment,
- Do not plug or unplug the power cord with wet hand.
TROUBLESHOOTING
If you installed the new power supply and the system is not working properly, please check the following:
- Make sure the AC power cord is plugged correctly into PSU inlet socket and the power switch is at the input “I” position.
- Make sure the wall socket, extension power cord, power strip or surge protector in use, fully functional and wall power switch is turned on.
- Make sure that all the connectors from the power supply are correctly plugged into the mainboard.
- Make sure there are no short circuits within the systems that could result from defective hardware or misplaced connectors.
- If your are not sure, take all parts out of the housing and only leave the mainboard inside together with the power supply. Disconnect all plugs, check them and then connect them again to the respective sockets.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>