MEEC TOOL 014402 20W Hot Melt Glue Gun Instruction Manual

MEEC TOOL 014402 20W Hot Melt Glue Gun

SAFETY INSTRUCTIONS

•  Keep the work area clean and well lit. Dark and cluttered work areas increase the risk of accidents and injuries.
•  Connect the product to a power point with at least a 10 A fuse. The product should be connected to a separate circuit.
•  Never leave the product unattended when switched on.
•  Place the product on a level I stable surface. Do not put the product on or near a hot stove, or over other appliances.
•  Do not touch hot surfaces. Use the handle.
•  Do not allow the power cord to hang over the edge of a table or worktop, or to come in contact with hot surfaces.
•  Do not immerse any part of the product in water or any other liquid.
•  If an extension cord is used the cross-sectional area of the wires must be dimensioned for the power supply to the product. Check that the mains voltage corresponds to the rated voltage on the type plate.
•  If the power cord or plug are damaged they must be replaced by an authorised service center to ensure safe use.
•  Pull out the plug before cleaning, before moving the product and when the product is not in use.
•  Do not dismantle the product or attempt to modify, or repair it.
•  Do not poke any objects into the openings on the product.
•  The product is only intended for household use.
•  Do not use the product outdoors.
•  This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without superv1s1on.
•  Note that the heater element will still be hot after the product is switched off­risk of burn injury.
•  Avoid skin contact. Avoid all contact with water and substances or liquids containing solvent.

IMPORTANT:

•  It is not possible to remove spots of hotmelt glue from clothes.
•  Wear safety glasses.
•  Allow the product to cool upright in its holder after use.
•  Pull out the plug during long pauses in the work.

SYMBOLS

TECHNICAL DATA

• Rated voltage/230 V ~ 50 Hz
• Output/20W
• Heating effect/6-12 g/min
• Temperature range/170-190°
• Safety class/11
• Protection rating/IP20
• Glue stick/r/J 7.2 mm
• Cord length/1.3m

DESCRIPTION

PARTS

1.  Charge opening
2.  Power cord
3.  Trigger
4.  Support
5. Nozzle

HOW TO USE

INTENDED USE
Intended for gluing wood, plastic, foam plastic, textile, tiles and ceramic, etc. The glue can also be used to seal holes and seal joints. The product is only intended for household use.

GLUING

1.  Insert a glue stick through the opening and push in all the way.
2.  Plug the plug into a power point.
3.  Allow the glue gun to warm up for about 5 minutes.
4.  Carefully press the trigger and apply glue to the surfaces of the joint. Join parts within 15 to 20 seconds after applying the glue. The glue congeals after about 30 seconds and reaches 90% of its full strength after1 minute. If the glue is applied thicker it takes longer to congeal, and shorter to congeal if applied thinly.
5.  Insert new glue sticks when necessary.

Tips for gluing

• Large surfaces should not be glued in one go, but should if possible be divided up into smaller sections. Apply the glue in wavy strings.
• Preheating of the joint surfaces with a hot air gun increases the bonding strength of the glue.
• Allow surplus glue and residue to completely cool before removing.
• Hotmelt glue joints can be separated or corrected by reheating with a hot air gun.
• The supplied long sleeve is intended for gluing joints difficult to reach, and for filling cavities and plugholes etc. The nozzle can only be changed when the glue gun is cold.
• Test temperature sensitive material first, by for example gluing small samples.

MAINTENANCE

NOTE:
Pull out the plug before cleaning and maintenance.

• Clean the product casing with a damp cloth and wipe dry. Do not use abrasive or solvent-based detergents.
• Never clean the product by dipping it in water or any other liquid.

STORAGE

Store the product, accessories and instructions in the original packaging. This ensures that all the information and parts are easily accessible

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>