MEEC TOOL 015276 Garden Pump Instruction Manual

[

](https://manuals.plus/wp-content/uploads/2022/07/MEEC-logo-2.png)

MEEC TOOL 015276 Garden Pump

SAFETY INSTRUCTIONS

• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.

• Keep children under supervision to make sure they do not play with the product. Do not allow children to clean or maintain the product without supervision.

• Familiarise yourself with the controls on the product and how to use them. Read all the instructions and safety instructions before use. Failure to follow all the instructions and safety instructions can result in a risk of electric shock, serious personal injury and/or material damage.

• Contact the retailer or qualified personnel if you have any problems or questions.

• Store these instructions so that they are readily available for everyone who uses the product. These instructions should be enclosed with the product if it is sold or passed on.

• Do not make any modifications to the product. Only use accessories recommended by the manufacturer.

• The product must only be used for its intended purpose and in accordance with these instructions. The product must only be used for its intended purpose and in accordance with these instructions, otherwise there is a risk of personal injury and/or material damage. The manufacturer cannot accept liability for personal injury and/or material damage resulting from improper use.

• A damaged cord or plug must be replaced by an authorised service centre or qualified person to ensure safe use.

• Do not use the product if it is damaged. Always check the power cord, plug and casing before use. If the product is damaged, or not working properly,
  it must be repaired or discarded.

• Pull out the plug immediately if the power cord or product gets damaged or stops working properly, otherwise there is a risk of electric shock.

• Qualified personnel must carry out repairs. Imperfect repairs can result in a risk of electric shock, serious personal injury and/or material damage.

• Do not pull the power cord to pull out the plug.

• Do not allow the power cord to hang over the edge of a table or worktop, or to come in contact with hot surfaces.
  Avoid kinking or bending the power cord.

• If an extension cord is used the cross­sectional area of the wires must be dimensioned for the power supply to the product.

• If the product is used outdoors, only use an extension cord approved for outdoor use.

• The product is not intended to transport water for human consumption.

• Do not use the product to transport corrosive, flammable or explosive substances such as petrol or other petroleum products, nitrogenous liquids, grease, oil, salt water or waste water from toilets, or liquid that has a higher viscosity than water.

• The temperature of the pumped water must not exceed 35° C.

• Keep this product out of the reach of children.

• Do not use the product if there are any persons in the water.

• Make sure the product does not suck up aquatic animals, such as fish.

• Pay attention to the risk of contaminating the liquid as a result of leaking lubricant.

• Protect electrical connections from moisture.

• Do not expose the product to temperatures below 0°C. Make sure that the product is not run without water.

• Do not pump aggressive liquids or abrasive material.

• Do not pull the power cord or float switch cord to move the product, and do not use them to secure the product from moving.

• The product is only intended for household use and is not suitable for commercial purposes.

• The manufacturer cannot accept liability for personal injury or material damage resulting from improper use.

IMPORTANT : The product must be connected to the mains with a residual current device of max 30 mA.

SYMBOL [](https://manuals.plus/wp-content/uploads/2022/07/MEEC-

TOOL-015276-Garden-Pump-FIG1.jpg)

TECHNICAL DATA

• Rated voltage 230 V ~ 50 Hz
• Nominal input power 800W
• Pump pressure 3.8 bar
• Flow, amax 53.31/min
• Lifting height, Hmax 38 m
• Suction height max 8 m
• Water temperature max 35° C
• Ambient temperature 0-40° C
• Protection rating IPX4
• Cord length 1m
• Connection 1″(R25)
• Size L34 x W20.5 x H24 cm
• Weight 5,8 Kg

DESCRIPTION

Ideal for irrigation or circulation and the uptake of clean water, e.g. for garden dams. The pump has an aluminium motor and a plastic pump housing.

USE

INTENDED USE
The product can be installed in a piping system that supplies domestic water. In suchcases the product should be connected to the piping system with a flexible hose, to avoid transmitting vibrations to the piping system.

WARNING!

• Risk of personal injury. If components are used that cannot withstand the pressure, or if the installation is not carried out correctly, the outlet tube canburst and spray out water, which can cause personal injury and/or material damage.
• Electrical safety. Do not use the product in damp areas.

NOTE:
The product is not intended for transportingdrinking water, only to transport water for a toilet or washing machine.

PREREQUISITES

• The plug must be plugged into a correctly installed and earthed power point.
• Check that the mains voltage corresponds to the rated voltage on the type plate.
• The product must be connected to a mains with a residual current device of max 30 mA for use in a pool or garden.
• If the product is used outdoors, only use an extension cord approved for outdoor use. The product must not be put in water.
• If an extension cord is used the cross­sectional area of the wires must be dimensioned for the power supply to the product. If an extension cord is used on a reel, pull out the full length of cord.

NOTE:
Risk of material damage. The product must be filled with water before it starts. Water does not need to be refilled during long term use. Do not leave the product unattended when running. Dry running can result in material damage.

FILLING WITH WATER AND STARTING

1. Remove the pump casing.
2. Fill the product full of water.
3. Replace the filter and fit the pump casing and seal.
4. Fill the suction tube with water if the product is only going to be used temporarily.
5. Open a tap on the outlet tube to release any air sucked in.
6. Start the product.
7. Switch off the product when water comes out without any air.

MAINTENANCE

WARNING!
Pull out the plug before cleaning and/or maintenance.

NOTE:
All the seals should be replaced if the product is dismantled.

• Do not attempt to carry out any measures other than as described in these instructions for maintenance and troubleshooting. Any problems not described in these instructions should be carried out by qualified personnel.
• Only use accessories and spare parts recommended by the manufacturer. The use of other accessories and parts can result in a risk of personal injury and/or material damage. It will also invalidate the warranty.

TROUBLESHOOTING

The troubleshooting guide on the next page is used to identify the causes of common problems and how they can be rectified. Contact the dealer if the problem can not be rectified with the help of the troubleshooting chart. Contact the retailer if you cannot solve the problem with the troubleshooting chart. The warranty does not cover damage resulting from repairs or attempted repairs carried out by unauthorised persons.

TROUBLESHOOTING CHART

No power supply.

| Check the power cord, plug, power point and fuse.
Overheating, usually because the temperature of the water is too hot.| ****

Identify and rectify the reason.

 | ****

The residual current device has tripped.

| Reset the residual current device. Contact an authorised electrician if the residual current device continues to trip.
---|---|---
Motor is faulty.| Contact an authorised service centre.

The product runs, but delivers no water.

| The suction tube is blocked.| Remove the blockage.

The product sucks air.

| Make sure that all the connections are airtight.
The product is blocked by a foreign object.| ****

Clean the filter.

Pump capacity too low.

| ****

The lifting height is too high.

| Do not exceed the maximum lifting height.
The diameter of the outlet tube is too small.| Use an outlet tube with a suitable diameter.
The outlet tube is blocked.| Remove the blockage.
The suction tube is blocked.| Clear the suction tube.
The outlet tube is bent.| Straighten out the outlet tube.

Outlet tube is leaking.

| Make sure that the outlet tube and all the connections are tight.

The product makes a noise.

| ****

Air in the product.

| Fill the product full of water. Make sure that all the connections are airtight.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>