D-Link DCS-4612EK Vigilance Outdoor Dome Camera Installation Guide

: June 6, 2024
: D-Link

D-Link DCS-4612EK Vigilance Outdoor Dome Camera Installation Guide

Before You Begin

This installation guide provides instructions for installing and configuring your camera. Additional documentation is also available on the D-Link support website.

Refer to the manual for your model for additional information on how to configure the device using the associated Setup Wizard. The manual and Setup Wizard may be found at https://dlink.com/support/.

Package Contents

This package includes the following items:

Vigilance Outdoor Dome Camera
Cable Waterproofing Connector
Mounting Kit
Allen Key
Alignment Sticker
Documentation

If any of the above items are damaged or missing, please contact your local D-Link reseller.

Note: Using a power supply with a different voltage than the one recommended for the device will cause damage and void the warranty for this product.

System Requirements

Computer running Microsoft Windows®
Internet Explorer 11

Hardware Overview

**DCS-4612EK/DCS-4614EK Front/Side
Figure 1: Front View Features

Table 1: Front View Descriptions
**

#	Feature	Description
1	microSD Slot	Slot for a microSD card.

2

| Vertical Adjustment Screw| Loosen to adjust the vertical angle of the camera
3| IR LED| Provides illumination for low- light environments

4

| Horizontal Adjustment Screw| Loosen to adjust the horizontal angle of the camera
5| Camera Lens| Fixed camera lens

**DCS-4618EK Front/Side

**

**Figure 2: Front View Features

Figure 2: Front View Features
**

#	Feature	Description

1

**DCS-4612EK/DCS-4614EK/DCS4618EK Cable Interfaces

**

Figure 3: Cable Interfaces

Table 3: Cable Interface Descriptions

#	Feature	Description

1

| Ethernet Jack| RJ-45 connector for Ethernet. Can also be used to power the camera using Power over Ethernet (PoE)
2| Power Connector| Connects to an optional 12 V / 1.5 A power adapter (not included)

3

| Reset Button| Press and hold for more than five seconds, then release to perform a factory reset

**Management Options

**

To configure and manage your camera, it is recommended that you download the associated Setup Wizard and the D-ViewCam software suite, both of which are available from the D-Link website.

Installing the Setup Wizard

Open a web browser, navigate to dlink.com/support/, and select your region.
On the next screen, enter the model number of your camera in the search bar and click Search. Click the picture of your camera. On the product page, click the Download button next to Setup Wizard.
Once the executable file has finished downloading, click it and follow the instructions to install the Setup Wizard.

Configuring the Camera

Ensure that your camera is plugged in (either using a 12 V 1.5 A power adapter or a PoE-enabled device) and connected to your computer with an Ethernet cable.
Open the Setup Wizard. It will display the MAC address and IP address of your camera. If you have a DHCP server on your network, this will be a dynamic IP address. If your network does not use a DHCP server, the network camera’s default static IP 192.168.0.20 will be displayed. Select your camera, then click the Link button to continue.
Figure 4: Launching the Setup Wizard
If this is your first time logging in, you will be prompted to create a password, which must be between 8 and 30 characters and must contain both letters and numbers. Press OK.
Figure 5: Creating a Password
To view the camera display, on the main screen of the Setup Wizard, click the Search button, then select your camera and click the Link button to open the camera’s web UI. Alternatively, open a web browser and type the camera’s IP address (displayed in step 2) into the URL bar and press Enter. Enter the password you created, and click Login to continue.
Figure 6: Authenticating

Installing D-ViewCam

Open a web browser, navigate to dlink.com/support/, and select your region.
On the next screen, click the D-ViewCam link and click the most recent version to download the D-ViewCam setup wizard (packaged as a zip file).
Once the file has finished downloading, unzip it, and click the executable file SetupTool.exe. Follow the instructions to install the D-ViewCam software suite.
For advanced viewing options, refer to the D-ViewCam User Manual.

Mounting the Camera

Note: It is highly recommended that you configure and test your camera before mounting it.

The DCS-4612EK, DCS-4614EK and DCS-4618EK can be installed on the ceiling or wall. The process is identical for both cameras.

Mounting the Camera

Use the included T10 or T15 screwdriver to unscrew the three screws on the dome cover and remove it.
Figure 7: Removing the Cover
Press the sides of the plastic lining and gently lift it to remove the lining from the camera.
Figure 8: Removing the Lining
Place the installation sticker on the ceiling or wall. Using a 4 mm drill bit, drill three holes 30 mm deep into the wall or ceiling. Drive the plastic wall anchors into the holes.
Figure 9: Attaching the Camera
Insert three mounting screws into the holes in the base of the device. Place the device against the mounting sticker and screw it in to attach it to the wall or ceiling. To ensure waterproofness you MUST mount the DCS-4618EK with all three of the provided screws.
Reattach the lining to the camera body by sliding it on until it clicks. Replace the dome cover and refasten the screws securing it in place.
Figure 10: Replace the dome cover

Adjusting the Lens

The angle, zoom and focus of the lens can adjusted using the web UI. For

information on how to do this, refer to the User Manual.
Figure 11: Positioning the Lens

Waterproofing Your Installation

To waterproof your camera, follow the instructions below. A round Ethernet cable, a crimping tool, and RJ-45 plugs are required for this procedure.

Place the washer around the base of the Ethernet connector as shown.
Figure 12: Attaching the Washer Ring
Thread the bare Ethernet cable through the waterproof connector as shown.
Figure 13: Threading the Cable
Attach an RJ-45 plug to the end of the cable using a crimping tool.
Figure 14: Attaching the RJ-45 Connector
Connect the RJ-45 plug into the Ethernet connector, then screw the waterproof connector to the Ethernet connector by turning it clockwise about one half-turn.
Figure 15: Attaching the Waterproof Connector
Screw the back part of the waterproof connector clockwise until there is a tight seal around the Ethernet cable.
Figure 16: Tightening the Connector
The power connector and reset button cables are not waterproof. It is recommended to use waterproof tape to protect them. Wind the tape around each cable in an overlapping manner to cover them.
Figure 17: Wrapping the Power Connector and Reset Button

Using the DCS-37-5 Mount (optional)

To ensure effective waterproofing for the DCS-4618EK , please carefully read the Installation Information Notice on page 12.

Using the DCS-37-6 Mount (optional)

1. To ensure effective waterproofing for the DCS4618EK, please carefully read the Installation Information Notice on page 12.

**Using the DCS-37-4 Mount (optional)

**

To ensure effective waterproofing for the DCS-4618EK, please carefully read the Installation Information Notice on page 12.
Waterproofing Your Installation

Installation Information

Model no.	DCS-37-4	DCS-37-5	DCS-37-6	Notice
Screw hole	Screw size	Screw hole	Screw size	Screw hole
DCS-4612EK DCS-4614EK	–	–	B	PM4*8mm

DCS-4618EK

(HW ver. A)

| –| –| G| PM48mm| A| PM410mm| To ensure effec tive waterproofing, remove the black rubber washers from the self-tapping screws that were included with the camera, then slip the washers onto the short flat-head screws of the DCS-37-5/37-6 before securing the camera to the mounting bracket.
DCS-4618EK

(HW ver. B)

| –| –| G| PM410mm| A| PM410mm| The screws to secure the DCS-4618EK camera to the DCS-37-5/37-6 mounting bracket are included with the DCS- 4618EK camera.
DCS-37-5| H| PM516mm| –| –| –| –|
DCS-37-6| F| PM410mm| –| –| –| –|

Additional Information

If you are encountering problems setting up your network, please refer to the user manual.

Product specifications, size and shape are subject to change without notice, and actual product appearance may differ from that depicted on the packaging. Visit your local D-Link website for technical support details.

Additional help is available online. To find out more about D-Link products or marketing information, please visit the D-Link support website at http://dlink.com/support/.

Warranty Information

Please visit http://warranty.dlink.com/ for warranty information for your region.

UKCA EMI CLASS A WARNING (only for class A product)

This equipment is compliant with Class A of EN 55032. In a residential environment this equipment may cause radio interference.

SAFETY INSTRUCTIONS

The following general safety guidelines are provided to help ensure your own personal safety and protect your product from potential damage. Remember to consult the product user instructions for more details.

Static electricity can be harmful to electronic components. Discharge static electricity from your body (i.e. touching grounded bare metal) before touching the product.
Do not attempt to service the product and never disassemble the product. For some products with a user replaceable battery, please read and follow the instructions in the user manual.
Do not spill food or liquid on your product and never push any objects into the openings of your product.
Do not use this product near water, areas with high humidity, or condensation unless the product is specifically rated for outdoor application.
Keep the product away from radiators and other heat sources.
Always unplug the product from mains power before cleaning and use a dry lint free cloth only

DISPOSING AND RECYCLING YOUR PRODUCT

This symbol on the product or packaging means that according to local laws and regulations this product should be not be disposed of in the household waste but sent for recycling. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to conserve the environment and protect human health.

GPL Code Statement

This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL code and LGPL code used in this product, are available to view the full GPL Code Statement at:

https://tsd.dlink.com.tw/GPL

The GPL code and LGPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. For details, see the GPL code and the LGPL code for this product and the terms of the GPL and LGPL. Please take it to a collection point designated by your local authorities once it has reached the end of its life, some will accept products for free. By recycling the product and its packaging in this manner you help to conserve the environment and protect human health.

Written Offer for GPL and LGPL Source Code

Where such specific license terms entitle you to the source code of such software, D-Link will
provide upon written request via email and/or traditional paper mail the applicable GPL and
LGPLsource code files via CD-ROM for a nominal cost to cover shipping and media charges as
allowed under the GPL and LGPL.

Please direct all inquiries to:

Email:
GPLCODE@dlink.com

Snail Mail:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
14420 Myford Road, Suite 100
Irvine, CA 92606