BLAUPUNKT TPMS HN1.0 Honda Plug and Play Instruction Manual
- June 6, 2024
- Blaupunkt
Table of Contents
BLAUPUNKT TPMS HN1.0 Honda Plug and Play Instruction Manual
CAUTIONS
Safety Notes
This TPMS (Tire Pressure Monitoring System) has been manufactured according to
established safety guidelines. However, dangers may still occur if the safety
notes in this manual is not observed. This manual is intended to familiarize
the user with the TPMS’s important functions. Read this carefully, prior to
using the appliance. Keep this manual in an easily accessible location. In
addition, do observe the instructions of the devices used in conjunction with
this appliance.
Road Safety Always observe the following notes for road safety:
- Device must be used in a way that compliments the safety of the user when driving the vehicle. It is recommended for the user to park at an appropriate location when examining the tires in case of abnormal alert.
General Safety
- Device is intended for installation and operation in a vehicle with 12V vehicle system outage, hence the device must be installed 500mm away from the DVD or high power equipment to prevent signal disruption.
- Do not dismantle or modify the device. Installation or repair should be performed by a specialist. Blaupunkt is not liable for any loss or damage resulting from unauthorized disassembly or modification to the device.
- Device is designed to monitor tire pressure and temperature only. Driver is responsible for the upkeep of the tires.
- Blaupunkt is not liable in case of loss of sensors. Contact your Blaupunkt dealer to purchase new sensors.
- Package comes with pre-set sensor for designated tires. In case of sensor replacement or change of sensor location, ensure the sensor are reprogrammed before operating.
- Please do not operate the device under such conditions (extremely high temperature or extremely low temperature); ensure that the temperature within the car ranges from -30°C to 80°C before you begin installation process and during operation.
- For abnormalities, please refer to the “Troubleshooting” section. Consult with Blaupunkt dealer for further examining, in case if the problem cannot be resolved.
This manual may be updated from time to time without any notice.
Disclaimer In no event shall Blaupunkt be liable for any direct, indirect, punitive, incidental, special consequential damages to property or life and whatsoever arising out of or connected with the use or misuse of our products. USA & CANADA: This product is not intended for sale in the United States and Canada. If purchased in the U.S. or Canada, this product is purchased on as-is basis. No warranty, whether expressed or implied is provided in the U.S. or Canada.
STRUCTURE & FUNCTIONS
Functions
Display
- Data Display
- Pressure Unit
- Display Battery Status
- OK Button
- Setting Button
- TPMS Alarm Icon
External Sensor
- Sensor Cover
- Battery Holder
- Battery
- Sensor
- Rubber Seal
- Base
Valve Sensor
- Dust Cap
- Aluminium Alloy Nut
- Aluminium Alloy Valve
- Transmitter
SPECIFICATIONS
Accessories
EXTERNAL SENSOR INSTALLATION
EXTERNAL SENSOR BATTERY REPLACEMENT
VALVE SENSOR INSTALLATION
DISPLAY INSTALLATION
WIRING DIAGRAM
DIFFERENT SCENARIO
SETTING
1. Sensor Pairing Setting
(It is required only when the sensors has switched location or be replaced)
-
d) External sensor
– Disassemble the external sensor from the front left tire & reinstalled, for sensor ID pairing activation. -
Valve sensor
– Releasing the air from tire continuously instead of intermittently, ensure that the releasing process is not less than 8 second.
– Do not exceed the maximum pressure of tire during inflating.
e) When system receives the signal, you will hear “Di-” which indicates successful sensor pairing (new sensor ID will be displayed). Then, it will continue to next order. -
Ensure that there is only one of the tire with sensor is activated during pairing, otherwise there is no guarantee that the sensor ID that really needs to be paired will be paired into the receiver.
-
To cancel the current pairing process by pressing return key, however pairing process cannot be cancelled after pairing process is successful.
2. Tire Position Exchange Setting
(It is required only when the tires has switched location)
Threshold Value Setting
TROUBLESHOOTING
If any of the following problem occur, please resort to Troubleshooting for the possible solutions. Consult Blaupunkt authorized dealer if problem persist.
https://taplink.cc/blaupunkt.apac
Designed and engineered by Blaupunkt Competence Centre
TPMS HN1.0E 1 311 21 010 45 01
TPMS HN1.0V 1 311 21 011 45 01