TORNADOR Z-030 Professional Car Detailing Tool Instruction Manual
- June 1, 2024
- TORNADOR
Table of Contents
Z-030 INSTRUCTIONS FOR USE
TORNADOR MAX™ Z-030
SAFETY REQUIREMENTS
Wear appropriate hearing and eye protection. Use in well ventilated area. Do not exceed 90 psi. Do not use with acidic, flammable or combustible products; “USE ONLY WITH TORNADOR® PRODUCTS.” Do not point cleaning tool at face or body. KEEP OUT OF REACH OF CHILDREN.
AIR REQUIREMENTS
The TORNADOR® MAX™ cleaning tool requires a constant air pressure between 4.5 and 6.5 bar at 78 to 90 psi, for optimum performance. DO NOT EXCEED 90 psi. CAUTION: Constant air supply rates vary depending on the size & power of the compressor. Always make sure tank & air lines are free from impurites, oil & water contamination.
INSTRUCTIONS FOR USE
Cleaning Fabric
- Remove large debris and vacuum area to be cleaned.
- Turn liquid air valve to upright position to deliver cleaning solution. Always use approved cleaning liquids.
- Hold cleaning nozzle 1 to 3 inches from area to be cleaned. Fully depress trigger. Begin with overlapping motion over area to be cleaned.
- Next turn valve to down position using just air and dry the area.
Cleaning Dashboard and Hard Surfaces
- Recommended air pressure set at 78 psi.
- Turn liquid valve to straight up vertical position, using a overlapping motion, spray area to be cleaned.
- Allow cleaning liquid to remain on surface for 10 -15 seconds.
- Follow with air only by turning valve to the horizontal down position. Begin drying with overlapping motion followed with a soft dry towel.
CARE & MAINTENANCE
- Avoid dropping the gun on the floor, disconnect when not being used.
- Turn liquid valve to the horizontal position after use to avoid dripping from tip.
- Tighten the jar while holding the lid to avoid loosening or stripping gun assembly.
- Many cleaning solutions will have specific uses. Always use approved cleaning liquids in the TORNADOR® Max cleaning tool. Using high alkaline or acidic products are not recommended. Always follow manufacturer’s dilution instructions. Neutral pH products and highly diluted water based products work best in the TORNADOR®. Always test in a small area.
- When cleaning with the TORNADOR®, use a microfiber towel to wipe any remaining debris or solution that needs to be wiped away.
- Keep the cone of the gun clean by removing the cone and rinsing frequently.
- Avoid excessive air pressure. Exceeding 90 psi can cause premature wear on the cone and assembly.
NOTE: After every use, place nozzle 2-3 inches into a bucket of soapy water while depressing the trigger once or twice to quickly remove dirt buildup in the cone. This will prevent premature wear.
TROUBLESHOOTING
| PROBLEM | SOLUTION |
|---|---|
| • Tip will not oscillate | • Check for low air pressure |
| • Tip moves slowly | • Check for dirt build-up and clean |
| • Tip drips fluid | • Keep liquid valve in the horizontal position when not in |
use
• Will not dispense liquid| • Check pickup tube for debris and rinse out
LIMITED WARRANTY
“90 day limited manufacturer’s warranty against manufacturing & part defects.” Warranty will be voided, if it is used for anything other than the intended use of the TORNADOR® cleaning tool. Use of any products, other the TORNADOR® products, with or in the TORNADOR® cleaning tool, voids warranty.
Copyright 2021 – ECP INCORPORATED – All rights reserved
www.tornador.us
Covered by one or more of the following: U.S. Patent Nos. 8,480,011;
8,690,077; 9,475,071; 10,189,034; 10,343,177; 10,730,062; 10,562,078;
Taiwanese Patent No. I617360 and U.S. Design Pat. Appl. Nos. 29/756,918;
29/756,919; 29/756,920; 29/756,921.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>