RECOM RMOD360-UW Series Single Output DC Converter Instruction Manual

RECOM RMOD360-UW Series Single Output DC Converter

Specifications

Product Name: RMOD360-UW Series DC/DC Converter
Model: RMOD360-80-24.5SUW
Input Voltage Range: 18-106VDC
Output Protections: Short circuit, over current, over temperature, input reverse polarity protection up to -106VDC

Product Usage Instructions

Installing the Device

WARNING: Electrical danger due to improper installation of the power supply unit can cause serious injury, burns, or death.

1. Before any installation or maintenance work, disconnect and lock off the mains supply and secure it against accidental connection.
2. Mounting orientation can be done in any direction.
3. Mount the DC/DC converter on a cooling metal surface.

Putting the Device into Operation

Important! Before applying power, ensure that the rated output current and voltage of the power supply meet the requirements of the application.
Derating: See derating information provided (refer to Fig. 3).

Faults and Troubleshooting
Depending on the degree of protection mechanism, the device automatically restarts after the fault condition is removed.

Dismantling and Disposing of the Device
The EG WEEE (Waste Electrical and Electronic Equipment) Directive applies to this product. Always dispose of packaging material and electrical devices or components via authorized collection or disposal points, not in household waste.

FAQ

Q: What should I do if I encounter a fault condition with the DC/DC converter?
A: Depending on the degree of protection mechanism, the device will automatically restart after the fault condition is resolved. If you encounter persistent issues, contact RECOM Techsupport for assistance.

General information

For your own safety, read the safety information before installing the power supply and putting it into operation.
Keep these instructions and the safety information as an important part of the product. Pass them on to any subsequent owner. For support and additional information, please visit www.recom-power.com.

Required knowledge and responsibility areas of the user/ operator

• This device may only be installed and put in operation by qualified personnel.
• There are no user-serviceable parts inside. Do not modify or repair the unit.
• Check the device for visible defects before each use
• The device may only be operated within the specified technical specifications
• Incorrect operation and improper installation can endanger your safety.

State of the art
The DC/DC converter is tested in accordance with the following directives and standards:

• CE (RoHS2, LVD)
• UL
• UKCA

Intended use

This product is a built-in DC-DC converter. The equipment shall be supplied from a DC source. The DC/DC converter is suitable for input voltages in the range of 18-106VDC (refer to Fig. 4). DC/DC converter is protected against output short circuit, output over current, over temperature and has also an input reverse polarity protection up to -106VDC

Installing the device

WARNING Electrical danger due to improper or faulty Installation of the power supply unit!

Can cause serious injury, burns or death.

• Follow the following RECOM step-by-step instructions
• Do not make any changes to the power supply
• Contact RECOM Techsupport if you have problems

To install the device, proceed as follows:

Step Description

1. Before any installation or maintenance work, disconnect and lock off the mains supply and secure it against accidental reconnection.
2. Mounting orientation can be done in any direction.
3. Mount the DC/DC converter on a cooling metal plate surface and ensure that the maximum allowed baseplate temperature is not exceeded. Use an heating pad between the DC-DC converter and the metal cooling surface in order to maintain good thermal contact. Refer to Fig. 3
4. The converter must be mounted with at least 4x M6 screws to ensure a secure installation. Refer to Fig. 1
5. The converter must be connected with the prescribed connectors. Refer to Fig. 2
6. Any usage which does not comply with the specifications may decrease the performance or damage the device.

Putting the device into operation

Important! Before applying power, ensure that the rated output current and voltage of the power supply meet the requirements of the application.

Derating .

See derating below (Fig. 3)

Safe operation

• Operate the DC/DC converter only according to the conditions and the ambient temperatures listed in the Specifications.

The unit should:

• not be operated if defective
• not be operated under full load without sufficient cooling
• be installed in a controlled environment compliant with pollution degree 2 (PD2)

Faults and troubleshooting
Depending on the degree of protection (a mechanism), the device restarts automatically after the fault condition is removed.

Liability and warranty

• RECOM Power GmbH assumes no responsibility and no liability for damages if:
• the unit is used for purposes not listed in the Intended use section
• the unit is operated outside of the specification
• the unit is modified in any way
• the unit is improperly installed
• the unit is operated in a defective condition
• the unit is exposed to corrosive chemicals or gasses
• the documentation is not kept up to date

Dismantling and disposing of the device

• Disconnect the dc-dc converter
• Uninstall the dc-dc converter

The EG WEEE (Waste Electrical and Electronic Equipment) Directive applies to this product. Always dispose of packaging material and electrical devices or components via authorized collection or disposal points, not in household waste.

Installation and Operating Instructions

DC/DC Converter: RMOD360-UW Series

Other applicable document:
Important Safety Information

Product printing symbol and safety mark description

©RECOM Power GmbH. The information contained in these instructions and accompanying drawings are the intellectual property of RECOM Power GmbH. This manual can change without prior notice.
RECOM Power GmbH
Münzfeld 35, 4810 Gmunden, AUSTRIA
+43 7612 88325 700 +43 7612 88325 801
[email protected] www .recom-power.com

References

• Homepage | Power Integrations

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>