ORVIBO A10 Smart Wi-Fi Switch User Manual

ORVIBO A10 Smart Wi-Fi Switch

Product Description

ORVIBO Smart WiFi Switch is a smart 1-channel module relay that converts the traditional single-pole switch into a smart switch, which can be controlled remotely on your smartphone app from anywhere. You could create the automation for the switch by setting the timer schedules, sunrise/sunset, or together with compatible ORVIBO smart home products. It adopts a WiFi communication protocol and also can work with Alexa, Google Home, and Siri’s voice. The switch is for indoor use only. The neutral wire is required. It works with single-pole light switches, does not work with 3-way switches or dimmer switches.

Packing List

Specifications

Installation -A10 Smart WiFI Switch

1. Turn off the power at the circuit breaker
   WARNING : Shock Hazard May result in serious injury or death. Turn off power at the circuit breaker or fuse before installing.

2. Pull out the existing switch from the wall

3. Remove the wallplate from the existing switch.

4. Unscrew the existing switch

5. pull it out of the junction box. Do not remove any wires.

6. Identify and label the wires

7. Identify the NEUTRAL wires and label the wires with the “Neutral” sticker.
   Note:

8. The NEUTRAL wire is usually white or grey

9. If there is no neutral, please call an electrician for help.

10. Identify the GROUND wires(most likely a bare copper or green), and label the wires with the “Ground” sticker.

11. Identity the LINE wires, and label the wire with a “Line” sticker

12. Identity the LOAD wires, and label the wire with a “Load” sticker
    Note:
    You can use an electrical tester to identify the LINE and LOAD wires or call an electrician for help.

13. Remove the existing switch
    Make sure the circuit breaker is powered off. Disconnect all wires from the switch.

14. Connect the Smart Wifi Switch
    Make sure the circuit breaker is powered off, Use wire connectors to connect the wires on the Smart Wifi Switch to the labeled wires coming from the wall in order.

15. Connect NEUTRAL wires

16. Connect GROUND wires

17. Connect LINE wires

18. Connect LOAD wires

19. Mount the switch and wallplate

20. Use the screws provided

21. Attach the bracket to the switch using the screws

22. Snap-on the wallplate

23. Turn on the power at the circuit breaker

Download the app and regiter

1. Download the ORVIBO Home app Scan the QRcode or go to the App Store to download the ORVIBO Home App
2. Regiter Launch the ORVIBO Home app and regiter a new account or login

Add device and Configuration

1. Tap on “+” at the upper right corner at the Home page of the App
2. Select the Smart WiFi Switch under “Switch & Outlet”tab
3. Turn the power on at the circuit breaker
4. When the light blinks slowly, check √，then hit “Add Now”

Add the Device to Smart Home Connect the device to WiFi , Make sure the WiFi name shown in the form is 2.4G hz not 5G Hz

Note : This switch only supports 2.4G Hz networks

Utilize the App Feature

Control the light

Set timing

Tap on the “ … ”on the switch, There are three functions on this screen.

Set countdown

You can edit the schedule by setting the time, sunrise, and sunset.

Create Scenes

Smart scene control allows you to control multiple devices together at one touch, via voice command or by a scene timer.

1. Go to the scene page, Tap “+” to create a new scene
2. Complete the new scene-setting.

Voice Control Via Siri

If you have an Apple mobile device, you can enable Siri voice control to the scenes you created. Set Siri Shortcuts Go to “Me”,find “Siri Shortcuts.” Click “Add to Siri”to customize your voice control from your Apple devices to home Appliances

method
Siri Voice command starts with “Hey,Siri.” “turn off the light”.

Support Amazon Alexa and Google Home

1. Link ORVIBO to Amazon Alexa / Google Assistant
   Launch the ORVIBO Home app, and find the guide via this path:” Me”->Sevice You can choose Amazon Alexa / Google Home for detailed instructions.

2. Control by Amazon Alexa / Google Assistant

3. Voice command try this..

4. AMAZON ALEXA

5. Alexa, turn off the lights

6. Alexa, turn off the lights

7. Google Assistant

8. Hey Google, turn on the lights

9. Hey Google, turn off the lights

FAQ

1. The light does not turn on

2. Light bulb(s） burned out

3. Breaker is OFF or tripped

4. Light not properly installed

5. Wiring error

6. How to reset the device
   You can reset it after the installation is completed. Quickly press the turn off button repeatedly for 4 times and then press the turn off button till the white light flashes slowly indicating the device is reset successfully and ready to be configured

7. Why does the lamp appear dimly lit or flickering?
   Some brand lamps flicker or dim if the power of the lamp is low. This phenomenon is related to the structure and drive of the lamp and is not a switch quality problem. You can replace lamps with a higher power or connect safety capacitors in parallel at both terminals of the lamp.

8. why can’t find the in-wall switch when adding it?

9. Confirm whether the in-wall switch enters the configuration state.

10. Keep the smart switch and the gateway as close as possible, re-power the power of the switch and try again.

Warranty Range And Duration

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

Contact us:
support.us@orvibo.com https://www.orvibo.com/en/support/supportCenter.html

References

• SUPPORT | Register Product, FAQs, Video & Download, Warranty & Return, Contact Us, Coupons & Giveaways

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>