Shenzhen Dongyou Technology DYWS Wireless Lavalier Microphone Instruction Manual
- June 5, 2024
- Shenzhen Dongyou Technology
Table of Contents
Shenzhen Dongyou Technology DYWS Wireless Lavalier Microphone Instruction
Manual
Please read this manual carefully before use, and keep it properly after reading.
You can charge your phone while using it
- a Collar clip
- b Mute button
- c switch key
- d Noise reduction key
- e Mute button
- f Mobile phone interface
- g Pickup hole
- h Charging port
Basic product parameters
Microphone transmitter
Frequency range| 2.4G| Charging input voltage| DC4.8~5.4v| Transmission
distance| barrier-free distance 20 meters + Human obstacle distance 10 meters+
---|---|---|---|---|---
Microphone| Silicon Microphone MEMS| Working time| about 6-8H| Signal to noise
ratio| 65dBm
Working current| 12mA| Charging interface| Type-C| Transmission delay| 45MS
Shutdown current| 7uA| Charging time| about 80min| Sensitivity (microphone)|
-38dB
Charging current| about 65mA| Battery capacity| polymer battery
80mAH
| Antenna type| ceramic antenna
Frequency response range| 20-20KHZ| Full battery voltage| 4.1~4.25V| Working
temperature| -10~45°C
Type-C/Lighting receiver
Frequency range| 2.4G| Charging input voltage| DC4.8~5.4v| Transmission
distance| barrier-free distance 20 meters + Human obstacle distance 10 meters+
---|---|---|---|---|---
Working current| about 25mA
/ about 32mA
| Charging interface| Type-C
/ Lighting
| Signal to noise ratio| 65dBm
Transmission
delay
| 45mS| Support mobile
phone charging
| support| Frequency
response range
| 20-20KHZ
Working temperature| -10~45°C| Storage emperature| -40~85°C| Power supply
mode| Type-C interface mobile phone
Lighting inter / mobile phone
face
Antenna
type
| ceramic antenna| | | |
Battery compartment
| Capacity | 650mAh | Charging input voltage | DC4.8~5.4v | Charging time | 2.5h |
|---|---|---|---|---|---|
| Charging current | 1A | Charging interface | Type-C | Charge the microphone | 4 |
times
Product operation instructions
microphone
| Power on| click the power button, the green light flashes slowly
---|---|---
Shut down| Press and hold the power button for 3 seconds, the green light is
off, and the machine is turned off
Connection status| green light is always on
Mute| click the mute button to switch, the red light is always on in mute
mode, and the green light is always on in non-silent mode
Unable to pair
| 4 click the 2 mic mute buttons to enter the green light and flash quickly, Then plug in the receiver (Lighting/Type-C)
Press the mute button again 4 to enter the green light flashing quickly, and pair yourself
Charging| the red light is always on
Fully charged| red light off
Low battery alarm| red light flashes slowly
Automatic shutdown| automatic shutdown after 3 minutes without connection
Receiving end
| Power on| plug in the phone to turn on, the green light flashes slowly
---|---|---
Shut down| unplug from the mobile phone and shut down
Connection
status
| green light is always on
Mute| click the mute button to switch, the red light is always on in mute
mode, and the green light is always on in non-silent mode
Noise reduction mode| click the noise reduction button to switch, the blue
light in the non-noise reduction mode is always on, and the green light in the
noise reduction mode is always on.
Charging compartment
| Charging status| green light flashes slowly
---|---|---
Fully charged| the green light is always on
Power shortage status| blue light flashes slowly
Charging the microphone in
the charging compartment
| the blue light is always on
The microphone is fully charged| the light does not turn on
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>