BIETRUN WXM16 Wireless Guitar System User Manual
- June 6, 2024
- BIETRUN
Table of Contents
WXM16 Wireless Guitar System
User Manual
If you have any questions, please feel free to contact us. E-mail: amazon@bietrun.com
Product introduction:
This Wireless guitar system uses UHF frequency band transmission, which has
the characteristics of long transmission distance, strong anti-interference
ability, low delay, and clear sound quality. It is easy to use, operate and
debug. The whole machine has extremely low power consumption and long battery
life, which can be widely used in wireless transmission of electric guitars
and other electronic musical instruments.
Note: Please read and follow all warnings carefully before use, and keep
this manual for subsequent use.
Product Description:
1.1 Transmitter and Receiver 1.2 Control and display
Disciam
| Serial | Part name | function | Notes |
|---|---|---|---|
| 1 | Charging port | External DC 5V power supply charges the product | (1)Charge |
it once before your first use; (2)Charge it when lack power.
2| Power button| (1)On/off: Press and hold to turn on, long press to turn off:
(2)Switch channel: When the transmitter is turned on, press the button to
switch channel.|
3| Indicator light| (1)White: Power-on state. (2)White flash: change the
channel. (3)Red flash lack power. (4)Red: Product charging Indication. Red
indicator light off: the power is full.When charging with the product on, the
indicator light is white after a full charge.|
4| Volume adjustment button| (1) Press this button, the volume will cycle
between 0 , +5 and +10 In sequence. (2) Long press for more than 3$ to lock
the frequency (see “4. Frequency Lock”).| After the product is locked, this
transmitter can only be paired with the receiver can no longer be paired with
other receivers.
5| Volume indicator light| Minimum 0, + 5 Increased, + 10 largest.|
6| Connection indicator light| After the transmitter Is connected to the
receiver, the indicator light Is green.| The connection Indicator cannot be on
if transmitter and receiver are not well connected
Product connection
3.1 Insert the receiver into the input port of the guitar speaker or the amplifier.
3.2 Insert tho transmitter into the 6.35mm audio hole of the electric guitar.
3.3 Turn on the transmitter, receiver, and amplifier, then adjust the volume to an appropriate position to enter the working state.
Frequency Lock:
When multiple sets of guitar wireless transceivers need to be used at the same
time in the same environment, there will be a problem that signals interfere
with each other and cannot be used. You can use the frequency lock function to
lock each set of transceivers to work independently without interference.
Setting method:
Turn on the transmitter and receiver. After the transmitter and receiver are
successfully connected (the receiver connection indicator lights up green),
press and hold the transmitter volume adjustment button (dB button) for more
than 3 seconds and then release, three-volume indicators lights flash at the
same time, indicating that the frequency lock is successful, after 5 seconds,
exit the frequency lock mode and enter the normal mode.
Note
- Alter the product is frequency locked, it can no longer be frequency-locked or cross-used with other receivers;
- When multiple sets of products are frequency-locked, only the frequency-locked receiver and transmitter can be turned on, and other products to be frequency-locked cannot be turned on. For example, when product A is frequency-locked, B, C… are in the off state, and when B Is frequency-locked, A, C…shut down, and so on, all can be switched on at the same time after all the frequency lock is complete.
Trouble Shooting:
Note: 1. After the product is frequency locked, it can no longer be frequency- locked or cross-used with other receivers; 2. When multiple sets of products are frequency-locked, only the frequency-locked receiver and transmitter can be turned on, and other products to be frequency-locked cannot be turned on. For example, when product A is frequency-locked, B. C… are in the off state, and when B is frequency-locked, A, C…shut down, and so on, all can be switched on at the same time after all the frequency lock is complete.
Trouble Shooting:
| No. | Problem | Solution |
|---|---|---|
| 1 | The transmitter and receiver can not be turned on | Charge first and check |
if the power indicator lights are on. (
2| The sound is intermittent and the receiver’s green light flashes| 1)Shorten
the distance between the receiver and the transmitter. (2)Adjusts the receiver
to the visual range as much as possible. (3) Switch channels.
3| No sound| (1)Check whether the receiver and transmitter have been turned on
normally and properly connected. (2)Whether the receiver is correctly
connected to the amplifier. (3)Whether the amplifier is turned on and whether
the volume is appropriate. (4)Check whether the transmitter is correctly
inserted into the audio/mic hole of the guitar. (5)Check whether the
transmitter and receiver are inserted in the wrong position. (6)Check whether
the guiles volume, tone, and balance are adjusted properly, and increase the
guitar volume.
4| The sound Is smal| 1) Must the volume of the amplifier. (2) Must the volume
of the guitar.
Product Parameters:
| Wireless Frequency | U Band | Way of Pairing P | aired by Factory default |
|---|---|---|---|
| Use time | about 6 hours | Power supply | polymer lithium battery |
| Wireless Distance | Indoor environment 30M |
Packing List:
- 1X transmitter
- 1X receiver
- 1X charging cable
- 1X User Manual
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Manufacturer:
SHENZHEN LONGXIANG INTELLIGENT TECHNOLOGY CO, LTD.
Address: FLOOR 4, BUILDING D, FUXINLIN INDUSTRIAL AREA,
HANGCHENG INDUSTRIAL ZONE FUHUA COMMUNITY XIXIANG
STREET, BAOAN DISTRICT SHENZHEN GUANGDONG CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>