Bietrun KYQ06 Voice Amplifier Instruction Manual
- October 30, 2023
- BIETRUN
Table of Contents
Bietrun KYQ06 Voice Amplifier
Package Included
- Please check all the items are included before use.
Overview
- Power
- Previous
- Play/Pause
- Next
- Mode
- Volume+
- Volume-
- Power Indicator
- Mic Signal
- Mode Indicator
- Charging Indicator
- TF Card Slot
- Reset
- MIC Input
- Type-C Input
- AUX-IN Input
Power/Mode
- Short press to turn on/off the voice amplifier.
Modes
Mode Switch
- Short press to switch mode. It will be in Bluetooth mode after being powered on without connection.
Sleep Mode
- The voice amplifier will be turned off automatically after 30 minutes without any connection(It won’t turn off if Bluetooth is connected).
TF Card Mode
- Insert the TF card, audio will be played automatically.
- When playing audio on TF card, Long press for 2 seconds to switch single song repeat/play all song.
- TF Card Support Format: FAT32, Maximum Capacity: 32GB.
- Playback Formats: MP3/WMA/WAV/FLAC/APE (Sample rate 8K~48K)
Bluetooth Mode
- One bar stands for a quarter of battery: 4 bars-100%; 3 bars-75%; 2 bars-50%;1 bar-25%.
Power Indicator
- One bar stands for a quarter of battery: 4 bars-100%; 3 bars-75%: 2 bars-50%:1 bar-25%.
Volume Control
- Short press -/+ button to adjust volume. It will be “Di Di” when reaching the maximum/minimum volume.
Play/Pause
- Short Press: play/pause.
- In TF Card Mode, long press: single song loop. Long press again: play all.
- In Bluetooth Mode, long press to disconnect and get into the Bluetooth re-pairing state.
Previous/Next
- In Bluetooth Mode, short press to switch.
- In TF Card Mode, short press to change song; long press to rewind/fast forward.
AUX-IN Mode
- When the audio cable is plugged into the AUX jack, the voice amplifier will automatically switch to the AUX-IN mode.
- If no audio cable is plugged in, pressing the M key will not switch to AUX-IN mode.
How to Use the Wired Headset
- Plug in the headset and press the +/- keys to adjust the volume (as shown in pic 1).
- Keep your mouth pointed at the mic when wearing.
- Please refer to the correct wearing way and speak toward the sound source(as shown in pic 3)
- Incorrect wearing way(as shown in pic 4) can lead to problems such as howling and low sound.
Tip: The foam windscreen can filter the disturbing airflow.
- A red indicator light will appear during charging and will turn off when fully charged.
Note: Please fully charge the device and then shut it down to ensure battery life when not use for a long time.
Audio Formats Supported
Audio Formats Supported by KYQ06
Specifications
- Please speak loudly and clearly in front of the foam windscreen (1-2cm) to achieve best effect.
- When using the headset microphone, please ensure that it does not face the voice amplifier directly to avoid howling.
- When there is 0 bar on the Power Indicator, please charge the device in time.
- Please fully charge the device and then shut it down to extend battery life when not use for a long time.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
More Information
- Manufacturer: Shenzhen LongXiang Intelligent Technology Co, Ltd.
- Address: Floor 4, Building D, Fuxinlin Industrial Area, Hangcheng Industrial Zone Fuhua Community Xixiang street, Baoan District Shenzhen Guangdong CHINA
- If you have any questions, please feel free to contact us.
- Email: Amazon@bietrun.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>