BIETRUN WXM29 XLR Microphone Wireless System User Manual

**BIETRUN WXM29 XLR Microphone Wireless System User Manual

**

Product Introduction

The XLR Microphone Wireless System adopts UHF frequency band transmission, which has the characteristics of long transmission distance, strong anti- interference ability, low delay and clear sound quality. Compatible with a variety of pickups. The working status is intuitive, and easy to use.

Note: Please read and follow all warnings carefully before use, and keep this manual for subsequent use.

Product Features

1. UHF frequency band wireless transmission, get rid of the trouble of cable entanglement, good anti-interference performance,crystal clear signal sound quality.
2. One-key startup, microphone music input switching, simple operation;
3. LED screen display, clear at a glance;
4. A variety of microphones meet different use occasions;

Product Description

Transmitter

1. working state of the microphone, including power, signal. frequency and 48V power supply.
2. If there is no keyless operation . it will enter power-saving mode and only display Power information. Press any key to reactivate the display

| Needed to change battery when ** turns to and flash
3| Mk/Musks switch| Up for audio input; down for mic input|
4| Power
button**|

1. Hold to turn on:long press to turn of
2. Change frequency: short press twice with powered on. 25 frequencies in total. microphone,

| When connecting the Condenser microphone, you need to press twice, then long press for 10 seconds to 48V mode (48V will be displayed on the screen)
5| Indicator| Green light when powered on|
6| Port Charging| Type-c charging port, input voltage DC5V 1A|

Receiver

Product Connection

Output Connection

Audio equipment with XLR port can be connected to this product, including mixers, multimedia speakers, power amplifiers, etc.

Input Connection

Trouble shooting

1. Charge first, then check whether the transmitter charging indicator light is on.
2. Press a nd hold the power switch for 2 seconds to power on. short press cannot power on.

2| Receiver can not be turned on|

1. Charge first, then check whether the transmitter charging indicator Ant is on.
2. Press a nd hold the power switch for 2 seconds to power on, short press cannot power on.

| No sound|

1. Check whether the volume of the microphone and the audio dev –ce nas been turned on;
2. Check whether the transmitter and receiver are successfully connected; the microphone information will be displayed if the connection is successful.
3. The amplifier which connect the receiver may need to set the input mode. please refer to the manual of the amplifier for setting:

4| Small sound|

1. Check whether the switch button of the transmitter is in the appropriate position. If the transmitter is connected to the microphone input, it should be adjusted to the microphone position.
2. Turn up the volume of the output device.

5| Intermittent sound|

1. Shorten the distance between the transmitter and the receiver, the visual distance does not exceed 50M, and the transmission distance wit be shortened when there are obstacles in the middle:
2. Change frequency;

6| Howling, screaming|

1. Reduce the volume of the amplifier or microphone:
2. Do not place the microphone too cb se to the speaker.

Product Parameters

Receiver

• Receiving frequency: U Band
• Sensitivity: 2mV
• Image interference ratio: >88dB
• Audio output: 800mV-1.4V
• Receive channel: 1
• Antenna: universal antenna
• Frequency stability: <0.002%
• Interference frequency ratio > 90dB
• Signal to noise ratio: >95dB
• Working range: Standard conditions 30 to 50 m
• Supply Voltage: DC 5V

Transmitter

• Carrier frequency: U Band
• Transmit power: 10mW
• Harmonic: <Main wave 40dB
• Battery: lithium battery
• Frequency stability: <0.002%
• Current consumption: <25mA
• Standard: Fixed frequency
• Antenna: built-in

Complex Index

• Dynamic Range: >95dB
• System distortion(<1%, 1K Hertz modulation)
• Frequency response: 50Hz-18KHz(+3dB)

Package List

• 1X Transmitter
• 1X Receiver
• 1X XLR to 6.35mm adapter
• 1X charging cable
• 1X User Manual

Manufacturer :
SHENZHEN LONGXIANG INTELLIGENT TECHNOLOGY CO, LTD. Address: FLOOR 4, BUILDING D, FUXINLIN INDUSTRIAL AREA, HANGCHENG INDUSTRIAL ZONE FUHUA COMMUNITY XIXIANG STREET, BAOAN DISTRICT SHENZHEN GUANGDONG CHINA

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

The device has been evaluated to meet general RF exposure requirement.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>