OPTICIS SVDF-200 S-Video Composite Video to 1-Fiber DVI Converter User Manual
- June 6, 2024
- opticis
Table of Contents
S-video/Composite video to
1-fiber DVI converter,
User’s Manual
SVDF-200
Doc No. : OC-SV210224 / Rev1.3
Welcome!
Congratulations on your purchase of the S-video/Composite video to 1-fiber DVI converter, SVDF-200. This manual contains information that will assist you in installing and operating the product.
Product Description
The SVDF-200, Component video to 1-fiber DVI converter receives SD format S-video/Composite video and converts to SXGA (1280×1024), 60Hz DVI optical signal and transmits up to 500 meters (1,640feet) over one (1) SC multi-mode fibers. OPTICS 1-fiber DVI receiver, DVFX-100-R is used as a pair to recover 1 fiber DVI to electrical DVI.
Shipping Group
- SVDF-200, Component video to 1-fiber DVI converter: One (1) unit
- AC/DC power adapter : One (1) unit of +5V, 3A (Locking type)
- User Manual
- Option Product: Mounting bracket
System Requirements for Setup
- Hardware requirements
- You must have S-video/Composite video sources such as a DVD player or camcorder.
- No special requirements for video sources
Installation
Important: Please keep the installation procedure below. Improper or no operation may result if the start-up sequence is not correctly followed.
Step 1
Carefully unpack the contents of the shipping group.
Step 2
Plug and fasten the 5V power adapters to the +5V DC jack on the rear side of
the converter. Ensure the Power LED is ON (Blue).
Step 3
Connect the S-video or Component video source to SVDF-200 over mini-DIN or RCA
cable. Please make sure the firm connections between the video source and
input port of the converter (S-VIDEO IN and COMPOSITE IN). If the connected
video source is active, the status LED (Blue) will be turned on.
[Note 1] SVDF-200 is designed to accept the first incoming video inputs. If
the user connects Composite video output to the SVDF-200 input port, it will
work as composite video to a 1-fiber DVI converter and vice versa.
Step 4
Connect the OPTICAL OUT to a 1-fiber DVI receiver, DVFX-100-R over multimode
SC-SC optical fiber.
Step 5
Plug DVFX-100-R to the DVI input port of the display.
Step 6
If you need on-site monitoring, connect S-VIDEO OUT or COMPOSITE OUT on the
front side of the converter to a dedicated local display over mini-DIN or RCA
cable. [Note 2] As the same concept as Note 1, if f the user connects
S-video output to SVDF-200 input port, it will work as S-video to 1-fiber DVI
converter, and only the S-VIDEO OUT port would be activated.
Note1: The maximum extension length by multi-mode fiber is 500 meters.
Note2: It is recommended NOT to use any intermediate cable or adapter in
between to avoid undesirable performance degradation.
Troubleshooting
The display shows only a black screen.
- Ensure that all plugs and jacks used by external power supplies (both Optics and others) are firmly connected. Ensure that the power and status LEDs are ON.
- Ensure that the video ports are firmly plugged into the source and display.
- Ensure that the converter and receiver modules are plugged correctly into the source and display, respectively.
- Check if the source and display are powered on and properly booted.
The screen is distorted or displays noises.
- Check if the graphic resolution is properly set. Go to the display properties of Windows and tap the settings.
- Reset the system. Disconnect and reconnect the optical fiber or 5V power adapters.
- Ensure that the input resolution is SD format (NTSC, PAL)
Maintenance
No special maintenance is required for the converter and power adapters. Ensure that the converter and power adapters are stored or used in a benign environment free from liquid or dirt contamination. There are no user- serviceable parts. Refer all service and repair issues to Optics.
Technical Support and Service
For commercial or general product support, contact your reseller. For technical service, contact Optics by email at techsupp@opticis.com or visit its website at www.opticis.com
Product Specifications
SVDF-200, Component video to 1-fiber DVI converter
-
Extension limit: 500 meters (1,640 feet) for SXGA (1280×1024), 60Hz refresh rate.
-
Graphic transmission bandwidth: Supports SXGA (1280×1024), 60Hz, or 1.085Gbps bandwidth per graphic channel.
-
Supporting resolution: 480i, 576i.
-
Fiber-optic connection: SVDF-200 has one (1) SC receptacles so as to be connected with one (1) SC multi-mode fiber, having 62.5 (50) / 125um core.
-
Dimensions (WDH): 104 x 112 x 28mm
-
Environmental Specifications
-
Operating temperature: 0°C to 50°C
-
Storage temperature: – 30°C to 70°C
-
Humidity: 10% to 85%
AC/DC Power Adapter
- Power Input: AC 100-240V, 50/60Hz 0.1A
- Power Output: +5 V, 3A SMPS DC-power Adapter
- Cord DC Jack: Core is 5 V and outer is GND.
Warranty Information
1 (One) Year Warranty
Optics warrants this SVDF-200 to be free from defects in workmanship and
materials, under normal use and service, for a period of one (1) year from the
date of purchase from Optics or its authorized resellers. If a product does
not work as warranted during the applicable warranty period, Optics shall, at
its option and expense, repair the defective product or part, deliver to the
customer an equivalent product or part to replace the defective item, or
refund to the customer the purchase price paid for the defective product. All
products that are replaced will become the property of Optics. Replacement
products may be new or reconditioned. Any replaced or repaired product or part
has a ninety (90) day warranty or the remainder of the initial warranty
period, whichever is longer. Optics shall not be responsible for any software,
firmware, information, or memory data of customer contained in, stored on, or
integrated with any product s returned to Optics for repair under warranty or
not.
Warranty Limitation and Exclusion
Optics shall have no further obligation under the foregoing limited warranty
if the product has been damaged due to abuse, misuse, neglect, accident,
unusual physical or electrical stress, unauthorized modifications, tampering,
alterations, or service other than by Optics or its authorized agents, causes
other than from ordinary use or failure to properly use the product in the
application for which said product is intended.
Dispose of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate
systems)
**** This symbol on the product or on its packaging indicates that this
product shall not be treated as household waste. Instead, it shall be handed
over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product.
The recycling of materials will help to conserve natural resources. For more
detailed information about recycling of this product, please contact your
local city office, your household waste disposal service or the shop where you
purchased the product.
© 2021 Optics Co., Ltd. All Rights Reserved
Revision 1.3 Feb 2021
Optics Locations
OPTICS HQ Optics Co., Ltd.
3F, 305, Sanseong-aero Sujeong-gu, Seongnam-si
Gyeonggi-do, 13354 South Korea
Tel: +82 (31) 719-8033
Fax: +82 (31) 719-8032
www.opticis.com
For order support, please contact your Distributor or Reseller.
For technical support, check with the Optics web site
www.opticis.com or
contact techsupp@opticis.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>