MOXA ioLogik 2500 Series Universal Controller Installation Guide

ioLogik 2500 Series Universal Controller

Installation Guide

Technical Support Contact Information
www.moxa.com/support

Package Checklist

• ioLogik 2500 series device
• 3-pin screw terminal block (for power input)
• 2 12-pin screw terminal blocks (for I/O)
• 2 8-pin RJ45-to-DB9 cables (CBL-RJ45M9-150)
• 1 antenna (only for wireless modules)
• Quick installation guide (printed)

Appearance

Top View

Front View

Physical Dimensions (unit = mm/inch)

Specifications

Hardware Installation

I/O Wiring

Mounting

There are two sliders on the back of the unit for DIN rail and wall mounting.

Mounting on a DIN rail
Step 1: If the spring-loaded bracket is locked in place, push the recessed button to release it.
Step 2: Insert the top of the rail into the upper lip of the attachment plate’s slot.
Step 3: The attachment unit should now snap into place along the rail.

Mounting on a wall (optional)

Step 1: Remove the DIN rail attachment plate.
Step 2: Install the wall mounting kit to the back of the unit with M3 screws.
Step 3: Install the unit to the wall. The heads of the screws should be less than 6.0 mm in diameter, and the shafts should be less than 3.5 mm in diameter, as shown in the figure at the right.

Connecting the Power

The ioLogik 2500 can receive power from a 12 to 48 VDC power source.
Input power is applied to the positive (V+) and negative (V-) terminals on the connector.

For most applications, it is desirable to ground the system by connecting the system’s power supply function ground (FG) to the power terminal’s ground and the chassis ground (indicated with red markings in the image at the right).

NOTE For safety reasons, wires connecting the power supply should be at least 2 mm in diameter (e.g., 12 gauge wires).

Connecting to a Network

The ioLogik 2500 has four built-in RJ45 Ethernet ports for connecting standard direct or crossover Ethernet cables.

LED Indicators

*Use the rotary switch to select which module’s I/O channel status is displayed.
**Wireless Modules Only.

System Configuration

Configuration via IOxpress Utility
The configuration of the ioLogik 2500 is mainly done with the IOxpress utility. IOxpress is a search utility that helps users locate an ioLogik 2500 device on the local network. The latest version of the utility can be downloaded from Moxa’s website.

• Default IP Address: 192.168.127.253
• Default Subnet Mask: 255.255.0.0

NOTE : Be sure to configure the host PC’s IP address to the same subnet as the ioLogik 2500. For example, 192.168.127.250

Load Factory Default Settings

There are three ways to restore the ioLogik 2500 to factory default settings.

1. Hold the RESET button for 5 seconds.
2. In the IOxpress utility, right-click on the ioLogik device to be reset and select Reset to Default.
3. Select Load Factory Default from the web console.

WARNING
This equipment is intended to be used in Restricted Access Locations. External metal parts are hot! Before touching it, special attention or protection is necessary.

How to Download the Software

Step 1: Click on the following link to open the Support & Downloads search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1

Step 2: Type the model name in the search box or select a product from the drop down box and then click Search.

Step 3: Click the Software Packages link to download the latest software for the product.

ATEX Information

1. Certificate number: DEMKO 15 ATEX 1603X
2. Certification string: Ex nA IIC T4 Gc
3. Standards covered: EN 60079-0:2012+A11:2013, EN 60079-15:2010
4. The equipment shall be installed in an enclosure that provides a degree of protection not less than IP54 in accordance with EN 60079-15 and accessible only by the use of a tool.
5. These products are for use in an area of not more than pollution degree 2 in accordance with EN 60664-1.

References

• Moxa - Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>