MOXA ioLogik E1500 Series I-O Ethernet Remote Installation Guide
- June 6, 2024
- MOXA
Table of Contents
MOXA ioLogik E1500 Series I-O Ethernet Remote
Package Checklist
- 1 ioLogik E1500 series remote I/O product
- Quick installation guide (printed)
Specifications
| Input Current | 150 mA @ 24 VDC |
|---|---|
| Input Voltage | 12 to 48 VDC |
| Operating Temperature | -40 to 85°C (-40 to 185°F) |
Installation
I/O Wiring
DI dry contact mode
DI wet contact mode (Ch-Ch isolation)
DI wet contact PNP/NPN mode (No CH-CH isolation
DIO_DI wet contact mode (no CH-CH isolation)
DIO_DO sink mode
Mounting and Cabling
The ioLogik E1500 can be used with both DIN rail and wall mounts. Whenmounting
on a DIN rail, release the bottom mounting kit, install the ioLogik on the
rail, and then restore the bottom mounting kit to fix the ioLogik to the rail.
When using wall mounting, release both the upper and bottom DIN rail kits. The
ioLogik E1500 has an M12 Ethernet port for connecting either a standard
direct-Ethernet or crossover-Ethernet cable via a locking M12 connector.
Power and Networking
Connect the +12 to +48 VDC power line to the ioLogik E1500’s terminal block V+
terminal, and connect the ground from the power supply to the V- terminal. If
an earth ground is available, connect the ground pin
LED Indicators
| Type | Color | Description |
|---|---|---|
| PWR | Green | System power in ON |
| Off | System power is OFF | |
| RDY | Green | System is ready |
| Green Blinking | Located | |
| Red | System Booting-up Error |
Green/Red
Blinking
| Safe Mode
Red Blinking| Firmware upgrade (LED flashes for 3
seconds then stays red until restart)
Off| System is not ready
LAN| Green| 100 Mbps
Amber| 10 Mbps
Blinking| Data Transmitting
Off| Ethernet Off
EXP| Green| Expansion Mode Ready
Red| Configuration Failure
Off| Stand-alone Mode
DI| Green| Channel ON
Off| Channel OFF
DIO| Green| Channel ON
Off| Channel OFF
System Configuration
Configuration via Web Console
Configuration of an ioLogik E1500 is done via the web console.
- Default IP Address: 192.168.127.254
- Subnet Mask: 255.255.255.0
Note: Be sure to configure the host PC’s IP address to the same subnet as the ioLogik E1500. For example, 192.168.127.253
ioSearch Utility
ioSearch is a search utility that helps users locate an ioLogik E1500 on the local network. The latest version of the utility can be downloaded from Moxa’s website
Load Factory Default Settings
There are three ways to restore the ioLogik E1500 to the factory default settings.
- Remove the two screws and the aluminum plate, and then press and hold the RESET button for 5 seconds.
- Right-click the specified ioLogik in the ioSearch utility and select Reset to Default.
- Select Load Factory Default from the web console.
Modbus Address Table
Refer to the user’s manual for details of the ioLogik’s Modbus address, or refer to the start address of the I/O channels in the web console under User- defined Modbus Addressing Default Address.
How to Download the Software
Step 1
Click on the following link to open the Support & Downloads search tool:
http://www.moxa.com/support/support_home.aspx?isSearchShow=1
Step 2
Type the model name in the search box or select a product from the drop
down box and then click Search.
Step 3
Click the Software Packages link to download the latest software for the
product
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>