Energizer 47485-T2 Battery Operated LED Ceiling Fixture With Wireless Switch Instruction Manual
- June 6, 2024
- Energizer
Table of Contents
Energizer 47485-T2 Battery Operated LED Ceiling Fixture With Wireless
Switch
Wireless Switch LED Ceiling Light
MOUNT THE CEILING LIGHT
- Remove the base of the ceiling light by rotating it counterclockwise. Use the provided screws and anchors to mount the base to the desired surface. Ensure it is firmly installed.
- Insert 4 C batteries (not included) into the ceiling light, noting polarity.
- Use the switch next to the batteries to set the brightness level to 100 or 200 lumens. 200 lumens will be a brighter option with less battery life. 100 lumens will be a less bright option but with longer battery life.
- Attach the light to the mounted base by turning it clockwise until it clicks into place.
NOTE: Ensure the mounting surface is capable of supporting the light with batteries installed.
MOUNT THE WALL SWITCH
- Remove the back mounting plate from the wall switch by sliding the wall switch remote upwards.
- Using the included screws, install them through the mounting plate holes. Do not overtighten.
- Mount the wall switch onto the mounting plate by gently sliding it downward to secure it in place.
WALL SWITCH OPERATION
- Press up on the switch to turn the light ON, press down to turn the light OFF.
NOTE: There is a 60min. timeout feature that will turn the light OFF to conserve battery life. The wall switch remote will control all Energizer Wireless Switch LED Ceiling Light (47485) within a 50-foot range.
WALL SWITCH BATTERY REPLACEMENT
- To replace the switch’s battery, slide and remove the battery door.
- Replace with one A23 battery, noting polarity.
- Replace the battery door and ensure it is firmly closed.
FCC NOTE: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
Suppliers Declaration of Conformity | Model #: 47485 | Jasco Products Co., 10
E. Memorial Rd., Oklahoma City, OK 73114,
www.byjasco.com
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC’s RF radiation exposure limits for general population/uncontrolled exposure, this device must be installed to provide a separation distance of at least 20cm from all persons.
WARNING: changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
For deals, to register your purchase and to tell us how we’re doing, simply scan the code or visit byjasco.com/deals
Like our product? Leave a review on your favorite retailer’s website or
amazon.com
Having problems? Let us know how we can help.
1-800-654-8483 between 7AM-8PM, M-F,
Central Time.
MADE IN CHINA/HECHO EN CHINA
©2021 Energizer. Energizer and certain graphic designs are trademarks of
Energizer Brands, LLC and related subsidiaries and are used under license by
Jasco Products Company, LLC.
Questions? Contact our U.S.-based Consumer Care at
1-800-654-8483 between 7AM-8PM, M-F,
Central Time.
90-day warranty. Visit www.byjasco.com for warranty
details.
WARNING
- BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE CAUSING INJURY AND PRODUCT DAMAGE
- DO NOT MIX OLD AND NEW OR OTHER BATTERY TYPES
- REPLACE ALL BATTERIES AT THE SAME TIME
- REMOVE BATTERIES IF THE PRODUCT IS TO BE UNUSED FOR EXTENDED PERIODS OF TIME
47485 EnSp Manual v1 12/15/20 MS
Read instructions or watch the easy-to-follow video. Scan code or visit byjasco.com/47485i
Discover innovative lighting solutions at www.byjasco.com/lighting
References
- 47485: Energizer Wireless Switch LED Ceiling Light Operation - YouTube
- Product Registration
- Jasco
- LED Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>