AMCREST AD410 4-Megapixel Video Doorbell Camera Pro User Guide

: June 6, 2024
: Amcrest

Table of Contents

In the Box
Step 2: Installing Corner or Wedge Bracket
Step 3: Connect Doorbell to Existing Wiring
- Inserting a MicroSD Card (Optional)
Step 4: Mounting the Doorbell
Step 5: Turn the Breaker Back On
Documents / Resources

AD410 4-Megapixel Video Doorbell Camera Pro
**User Guide
**

In the Box

AMCREST AD410 4 Megapixel Video Doorbell Camera Pro - In the
Box

NOTE A corner bracket can be used to angle the doorbell 15° and the wedge bracket can be used to angle the doorbell upward or downward at a 5° angle.

Step 2: Installing Corner or Wedge Bracket

A. Remove your existing doorbell from the wall and disconnect the wires. These are the wires we will be using to install your new Amcrest Wi-Fi Doorbell. B. Place a corner or wedge bracket on the mounting surface and mark the drill holes with a marker or pencil.

C. Attach a mounting bracket to the corner or wedge bracket and press in to snap the brackets together. AMCREST AD410 4 Megapixel Video Doorbell
Camera Pro - Installing 3

D. For Wood, Drywall, or Soft Surfaces: Secure the brackets to the mounting surface using a screwdriver and mounting screws.
For Concrete, Stucco, or Brick: Using your previously marked holes as a guide, drill holes into the mounting surface using the included masonry drill bit. Then, insert wall anchors and secure the brackets using a screwdriver and mounting screws.

Step 3: Connect Doorbell to Existing Wiring

Loosen the terminal screws located on the back of your Wi-Fi Doorbell using a screwdriver. Place your existing doorbell wiring underneath the terminal screws, then re-tighten the terminal screws to secure the wires.

NOTE If your existing doorbell wiring is too short, use the included extra wires and wire nuts to extend your wiring. Remove the terminal screws completely then thread the screws through the extra wire.

NOTE To attach the wires, align the ends of the two wires, place the wire nut over the exposed wiring and twist the wire nut clockwise to tighten.

Inserting a MicroSD Card (Optional)

On the back of the device locate the MicroSD card slot. Raise the MicroSD card ﬂap and insert the MicroSD card, gold pins down. Secure the ﬂap back to the doorbell.
Supports 128GB MicroSD Card (Class 10 or Higher)

Step 4: Mounting the Doorbell

Feed the wiring back into the wall. Then, place the doorbell onto the mounting bracket and slide it down to secure it.
NOTE You will hear a click sound once the doorbell has been secured to the bracket.

Step 5: Turn the Breaker Back On

The physical installation is now complete. Turn your breaker back on and allow the doorbell to power up. It may take the doorbell up to 2 minutes to fully power up.

Amcrest Smart Home

Now it’s time to set up the Amcrest Smart Home App. To connect your Amcrest Wi-Fi doorbell to your Android or iOS mobile device, download the Amcrest Smart Home app and follow the instructions in the app setup. AMCREST AD410 4
Megapixel Video Doorbell Camera Pro - figure 6

We’d Love to Hear From You!
We wanted to personally reach out and thank you for purchasing from our Amazon store. Selling on Amazon is what we do to support our family, and product reviews are the lifeblood of our business. It would mean the world to us if you could take one minute of your time to help share the love by leaving us an honest review using the link below:
www.amazon.com/ryp
Thank you again for being one of our amazing customers!
Sincerely,
Amcrest Team

How can we help?
We are dedicated to providing the highest quality support to our customers and are available 7 days a week.

Online Video Tutorial & Quick Start Guide
amcrest.com/support
Need help?
support@amcrest.com

Regulatory Information
The regulatory information herein might vary according to the model you purchased. Some information is only applicable for the country or region where the product is sold.

FCC Information
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause undesired operation.

FCC Compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
For class B devices, these limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

www.amcrest.com/fcc