GE Profile PFD95GSPTDS 7.8 cu. ft. Capacity Smart Front Load Gas Dryer with Steam and Sanitize Cycle Instruction Manual
- June 6, 2024
- GE Profile
Table of Contents
PFD95GSPTDS
GE ProfileTM 7.8 cu. ft. Capacity Smart Front Load Gas Dryer with
Steam and Sanitize Cycle
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
ELECTRIC DRYER RATING
120V/240V| 5600W, 25A, 60Hz
120V/208V| 4300W, 23A, 60Hz
EXHAUST OPTIONS: 4-way via rear, left, right, and bottom. (The right, left, and bottom venting options require Side Vent Kit: GFA28DSVN)
CIRCUIT REQUIREMENTS: An individual, properly grounded branch circuit, protected by a 30-amp circuit breaker or a time-delay fuse, is required.
NOTE: Dryer wall outlet must be located within 36″ of service cord entry and accessible when the dryer is mounted in position.
INSTALLATION INFORMATION: For complete information, see the installation instructions packed with your dryer.
PFD95GSPTDS
GE Profile ™ 7.8 cu. ft. Capacity Smart Front Load Gas Dryer with Steam and
Sanitize Cycle
SPECIAL INSTALLATION REQUIREMENTS:
STACKED INSTALLATION:
Brackets for stacking dryer over washer are not included with the dryer. Order
part no. GFA28KITN.
ALCOVE OR CLOSET INSTALLATION:
If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
The dryer MUST be exhausted to the outside.
Minimum clearances between dryer cabinet and adjacent walls or other surfaces
are 0″ on all sides and top.*
Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet
contains both a washer and a dryer, doors must contain a minimum of 120 sq.
in. of open area equally distributed.
No other fuel-burning appliance shall be installed in the same closet with a
gas dryer.
BATHROOM OR BEDROOM INSTALLATION:
The dryer MUST be exhausted to the outdoors.
The installation must conform with the local codes, or in the absence of local
codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223
for gas dryers.
MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET
INSTALLATIONS:
Minimum clearances to combustible surfaces 0″ all sides and top.*
FOR MORE INFORMATION ON VENTING KITS AND
ACCESSORIES, PLEASE CALL 1-800-GE-CARES.
*For improved performance, a 1/2″ clearance is suggested on each side.
STACKED DIMENSIONS (IN INCHES)
PEDESTAL DIMENSIONS (IN INCHES)
GFP1528PNDG – DIAMOND GRAY
GFP1528PNRS – SAPPHIRE BLUE
GFP1528PNSN – SATIN NICKEL
GFP1528SNWW – WHITE
This optional 16″ pedestal raises the door opening and height of the washer or dryer.
DRYER EXHAUSTING INFORMATION –METAL DUCT ONLY
For complete information, see installation instructions packed with your
dryer.
DUCTING MATERIALS: For best performance, this dryer should be vented with a 4″ diameter all rigid metal exhaust duct. If a rigid metal duct cannot be used, then UL-listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see the installation instructions packed with your dryer for complete instructions when using flexible metal (foil type) ducting.
EXHAUST LENGTH CALCULATION:
- Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of the dryer, add one turn.
- The maximum length of a 4″ rigid (aluminum or galvanized) duct that can be tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length
should be treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
CAUTION: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampened wall cap to prevent backdrafts, birds nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.
FOR MORE INFORMATION ON VENTING KITS AND ACCESSORIES, PLEASE CALL 1-800 -GE-CARES.
FEATURES AND BENEFITS
Steam Sanitize – Reduce certain types of bacteria by 99.8%, refresh small
loads, and de-wrinkle larger loads, all with the power of steam.
Adaptive MySettings – By learning your preferences, the dryer personalizes
your cycle selections automatically.
Washer Link – Wirelessly link your washer to your dryer so you only have to
choose a setting once.
Smart Features Powered by SmartHQ™ – Start, stop, and monitor your laundry
from anywhere while receiving real-time notifications and updates.
Stainless Steel Drum – Enjoy premium durability with a drum that resists rust
and helps protect clothes.
Quick Dry – This cycle quickly dries individual items and small loads, making
it perfect for families on the go.
Reduce Static – Prevent static cling with a gentle mist near the end of the
cycle.
Wrinkle Care – Prevents wrinkles by extending the tumble without heat.
Damp Alert – Signals when clothes reach the ideal dampness level for ironing
or air drying.
Check Vent Notification – Receive a notification when the dryer vent needs to
be cleaned, ensuring safe operation and optimal drying performance.
Closet Depth Install – 32″ Closet Depth provides installation flexibility with
limited space required.
Convenient 4-Way Venting – Flexible venting options allow venting from the
front, rear, or either side.
ENERGY STAR® Qualified – Meets or exceeds federal guidelines for energy
efficiency for year-round energy and money savings.
Model PFD95GSPTDS – Carbon Graphite
For answers to your Monogram, GE Café™, GE Profile™, or GE Appliances product
questions,
visit our website at geappliances.com or call GE
Answer Center® Service, at 800.626.2000.
Listed by Underwriters Laboratories
Specification Revised 2/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>