Shine KITCHEN SJV-107 Cold Press Vertical Slow Juicer User Manual

Shine KITCHEN SJV-107 Cold Press Vertical Slow Juicer

GENERAL SAFETY REGULATIONS

Special Notice:
To ensure the safe usage of this machine and to avoid injury and property damage to you and to others, please read this instruction manual carefully and follow all of the safety warnings and precautions. Failure to follow the safety warnings may lead to accidental injury or damage. Do not allow unattended children or persons with disabilities to use this machine.
Safety Warnings:

• This appliance is for household use only. It is not for commercial use.

• It is strictly prohibited to use this appliance during non-load operation or overloaded operation.

•  Do not touch moving parts during operation or injury may occur.

• Do not use this appliance on a tilted or unstable table or surface.

• Do not use finger, spoons, knives, chopsticks, or other foreign objects to push produce into the Feeding Chute.

•  Do not use damaged or malfunctioning electrical sockets or fire or personal injury may occur.

•  Do not use the appliance near high temperatures or fire or personal injury may occur.

•  If the plug, power cord, or other parts are damaged, stop using the appliance immediately. Contact the service center for repair or replacement before use.

• Before disassembling the appliance, make sure that the power is off and the appliance is unplugged.

•  Damage to the power cord must be repaired or replaced by the manufacturer or its authorized service center.

•  Keep out of the reach of children. Do not let children or disabled persons operate the appliance unattended.

•  Do not use accessories that did not come with this appliance.

•  Before using the appliance, please confirm that the power is in accordance with the specification of this appliance to avoid damage or other risks.

•  Ensure that each of the parts are clean and undamaged before using the appliance.

• Clean immediately after use.

• If the appliance does not work, refer to the Troubleshooting section of this guide.
  If the appliance still does not function normally, contact your service center for maintenance or repair. Do not disassemble the appliance by yourself.

• This appliance is not designed to grind dry goods such as rice, dried soybeans,
  or grains.

• Keep this appliance at least 12 in. / 30 cm away from other appliances.

PRODUCT INTRODUCTION

Parts

down.
t| Feeding Chute| Specially designed to help autofeed your produce into the juicer.
y| Auger| Hard-edged auger cuts through leafy greens and stringy produce so you don’t get any jams. Being edgy is good.
7| Brush| Multitasking tool that makes cleanup a breeze.
8| Pulp Container| Catches pulp.
9| Juice Container| Catches juice.
10| Sealing Ring| Makes sure there’s no juice that gets into the motor base.
11| Pressure Plug| Makes it easy to clean the pulp outlet.
12| Juice Cap| Stops the juice from dripping when you are done juicing.

Specification:

We are so happy to welcome you to the #juicetribe!
Please take a moment to read through this quick start guide before you move on to the assembly instructions so you can enjoy the best operation of your new tool for healthy living! For the best juicing experience:

• Your juicer will not turn on unless the safety switch is completely engaged. To do this, please be sure to follow the assembly instructions on the following pages completely to ensure the safety switch is completely engaged.

•  We recommend cutting your fruits and vegetables into 1-2 inch small pieces before feeding them into the chute. While it seems like more upfront time to chop then juice, it will save time while juicing and produce a higher volume of juice from your produce.

•  Your included cleaning brush is located on the back side of your packaging insert. Please be sure to flip your packaging over in order to take it out.

• While juicing, feed in produce then watch for the pulp to extract out of the front of the machine. Do not force the machine to work faster by overfeeding the machine. You may feed the juicer continuously, but always ensure the pulp is coming out at the same rate of your feeding. If the pulp is not coming out at the same rate, pause your juicing and use the reverse feature to ensure there is no produce blocking the feeding chute or pulp extraction. After doing this, you may resume juicing at a regular rate.

• It is simple to clean your machine after juicing by first running water through the chute with the machine on. This will push out most of the remaining pulp and make cleaning easier.

• To clean, twist off the entire top portion of your juicer and carry it to the sink. For best results, rinse each part right away with warm soapy water. This process should take 3-5 minutes. Your cleaning brush can help you quickly remove any pulp fiber that is attached to the screen. Take special care to remove the pressure plug from the bottom of the auger housing to clean it. Then place it back to ensure it does not become separated from your juicer between uses.

• Your machine is equipped with overheating protection. This machine has a compact motor that is designed to run for 10 minutes continuously. If your motor starts
  to heat up, it will automatically shut off until it cools back down in order to prevent damage to the motor by overheating. Wait until the machine cools down before resuming any juicing activity.

•  We offer replacement parts and additional juicing accessories at www.shinekitchen.co. If you need support or special shipping options, please contact our customer service center at 1-888-254-7336.

HOW TO ASSEMBLE

Attach the Auger Housing
Align the “•” mark on the Auger Housing with the “ ” mark on the Main Body, then rotate clockwise so that the “•” mark is aligned with the “ ” mark.

Insert the Juicing Screen
Insert the Juicing Screen into the center of the Auger Housing until it is firmly in place. The notch that is visible on the screen should slide into the front notch in the top of the auger housing nearest to the pulp exit.

Insert the Auger
Insert the Auger into the center of the Juicing Screen and through the silicone sealing ring of
the Auger Housing. Firm pressure may be needed.

Attach the Feeding
Align the “•” mark on the Feeding Chute with the “ ” mark on the Auger Housing, then rotate clock- wise so that the “•” mark is aligned with the “ ” mark.

Use the Included Accessories
Place the Pulp Container in front of the machine under the pulp exit. Place the Juice Container to the right of the pulp container under the juice exit. Make sure the Juice Cap is completely closed before you begin juicing. Insert the Pusher into the Feeding Chute.

 USING THE SLOW JUICER

Please thoroughly clean all non-electrical parts with soap and water before using the juicer for the first time. Use a damp cloth or sponge to clean the Main Body. Do not submerge or use running water to clean the Main Body.
The juicer has a built-in safety switch that will prevent the juicer from operating unless all the parts are assembled correctly.
Power Switch:
ON: Press the top portion of the Power Switch to the ON position to start the motor. Press the bottom portion of the Power Switch to turn off the motor.
REV: Press and hold the bottom portion of the Power Switch in the REV position to run the motor in reverse. This is helpful to clear out any hard produce that may cause the juicer to stop.
Automatic Shut Off:
You juicer is equipped with an automatic shut off feature to protect your motor from burning out. If you overheat your motor during juicing, your machine will automatically shut off. If this happens, it is recommended to allow you juicer to rest for 20-30 minutes before resuming operations. For additional information see your troubleshooting guide on page 13.

 HOW TO DISASSEMBLE

Remove Feeding Chute
Rotate the Feeding Chute counterclockwise until the “•” mark is aligned with the “ ” mark. Remove the Feeding Chute by pulling upwards.

Remove Auger
Pull the Auger straight up and out of the Juicing Screen and Auger Housing.

Remove the Juicing  Screen
Pull the Juicing Screen straight up and out of the Auger Housing.

Remove the Auger Housing
Rotate the Auger Housing counterclockwise until the “•” mark is aligned with the “ ” mark on the Main Body. Remove the Auger Housing by pulling upwards.

CLEANING AND MAINTENANCE

1. Clean the following parts with soap and running water. These parts may be soaked for easier cleaning. Use both ends of the Brush to thoroughly clean and remove any left over pulp.
2. Use a damp cloth or sponge to clean the Main Body. Do not submerge or use running water to clean the Main Body.

Sealing Ring*

1. Disassembly: Locate the circular, silicone sealing ring from the bottom of the Auger Housing and push its outer edge toward the center until it comes off completely.
2. Assembly: After it is thoroughly dried, put the sealing ring properly back in its place. Compress the sealing ring from two sides and slide it into the center portion of the Auger Housing with the larger side facing up. Adjust the ring until it is fitted above and below the plastic ridge. Once properly in place, the sealing ring should be secure.

BEFORE USING

damage the juicing parts.
Do not use hard or dried food.| Certain hard or dried foods can damage the juicing parts.
Cut fibrous produce into 1-inch pieces.| Long and stringy fibers can wrap around the Auger and cause the juicer to stall or damage to the juicing parts.
Do not put hard pits or seeds into the juicer.| Hard pits and seeds can damage the juicing parts. Please remove pits and seeds from the produce before juicing.
Only use the included Pusher to push food into the Juicer.| Other objects such as knives or spoons can damage the juicing parts.
Do not operate the juicer for more than 10 minutes at a time.| Overusing the juicer can cause the motor to overheat. Please wait 5-10 minutes between operations.
Do not put the pulp through a second time.| Re-juicing the pulp can cause the juicer to back up and damage the juicing parts.
Enjoy your juice as soon as possible.| We recommend drinking your juice immediately for the best taste and nutrition.
Squeaking sounds are normal.| It’s from friction as the pulp rubs against the moving parts of the juicer.
Feed the juicer slowly.| Please keep the juice level in the Auger Housing under the MAX line or the juice may overflow. Wait for juice and pulp to exit before adding more produce.

TROUBLESHOOTING

The motor does not turn on.| • Check that the power cord is plugged into a working socket.

• Check that all parts have been assembled correctly.

• If your machine may have shut off due to overheating allow your machine to rest until it has cooled down and then try restarting operations.

• Contact your customer service center.

---|---
Trouble removing the Feeding Chute.| • Check whether there is a lot of pulp in the Auger Housing. If so, turn the juicer on to remove the excess pulp.

• Check whether there is any hard objects stuck in the Feeding Chute. The REV button may help dislodge it.

• Contact your customer service center.

The juicer stops during operation.| • Use the REV button to dislodge any stuck pulp or produce.

• Feed the juicer at a slower pace.

• Cut your produce into smaller pieces.

• Contact your customer service center.

Leak from the bottom of the Auger Housing.| • Check to see if the silicone sealing ring is in place at the bottom center of the Auger Housing.

• Check to see if there is any damage to the silicone sealing ring.

• Feed the juicer at a slower pace.

• Contact your customer service center.

The Auger Housing moves while juicing.| • This is normal during operation and is designed to reduce strain on the moving parts.

References

• Shine Kitchen Co. Products | Tribest
• Shine Kitchen Co. Products | Tribest

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>