SUPERATV Polaris Ranger XP 900 Scratch Resistant Flip Windshield Instruction Manual
- June 3, 2024
- SUPERATV
Table of Contents
SUPERATV Polaris Ranger XP 900 Scratch Resistant Flip Windshield Instruction Manual
sales@superatv.com
www.superatv.com
Windshield Cleaning:
– Do not use Rain-X®, Plexus® or any other protector, wax, or polish.
– Do not use window cleaning fluids (Windex, 409, etc) or any solvents
(gasoline, denatured alcohol, acetone, etc).
– Never use abrasive cleaners, abrasive pads, or gritty cloths.
– Do not use a windshield wiper blade or install a motorized windshield wiper
– Never use razor blades, scrapers, squeegees, brushes, etc.
- Thoroughly rinse Windshield to float off dirt and mud.
- Using a soft cloth, or microfiber cloth, clean Windshield with warm water and a gentle detergent. Baby shampoo, rubbing alcohol, or hand washing soap can also be used.
- To prevent water spots, use a chamois to blot Windshield dry.
Liability Statement
SuperATV’s® products are designed to best fit user’s ATV/UTV under stock
conditions. Adding, modifying, or fabricating any factory or aftermarket parts
will void any warranty provided by SuperATV® and is not recommended.
SuperATV’s® products could interfere with other aftermarket accessories. If
user has aftermarket products on machine, contact SuperATV® to verify that
they will work together. Although SuperATV® has thousands of satisfied
customers, user should be aware that installing lift kits, long travel, or
suspension kits, tires, etc. will change the ride of machine and may increase
maintenance and part wear. Operating any off-road machine while, or after,
consuming alcohol and/or drugs increases risk of bodily harm or death. No
warranty or representation is made as to this product’s ability to protect
user from severe injury or death. SuperATV® urges operators and occupants to
wear a helmet and appropriate riding gear at all times. By purchasing and
installing SuperATV® products, user agrees that should damages occur,
SuperATV® will not be held responsible for loss of time, use, labor fees,
replacement parts, or freight charges. SuperATV®, nor any 3rd party, will not
be held responsible for any direct, indirect, incidental, special, or
consequential damages that result from any product purchased from SuperATV®.
The total liability of seller to user for all damages, losses, and causes of
action, if any, shall not exceed the total purchase price paid for the product
that gave rise to the claim. SuperATV® will warranty only parts provided by
SuperATV®. Any damage or problems with OEM housings, bearings, seals, or other
manufacturers’ products will not be covered by SuperATV®. SuperATV® parts and
products are not warrantied if item was not installed properly, misused, or
modified. Installing, adding, modifying, or fabricating any factory or
aftermarket product to your ATV/UTV may violate certain local, state, and
federal laws. Be advised that laws vary depending on town, city, county,
state, etc. Use of certain products on public streets, roads, or highways may
be in violation law. The Buyer is solely and exclusively legally and
personally responsible for any violation of the law by the installation or use
of the product. You must abide by all local, state, and federal laws,
including but not limited to vehicle safety, traffic laws, and ordinances. It
is your responsibility to know the laws and how they apply to you. The Buyer
is responsible to fully understand the capability and limitations of his/her
vehicle according to manufacturer specifications, warnings and instructions
and agrees to hold SuperATV® harmless from any damage resulting from failure
to adhere to such specifications, warnings and/ or instructions. The Buyer is
also responsible to obey all applicable federal, state, and local laws and
ordinances when operating his/her vehicle while using this product, and the
Buyer agrees to hold SuperATV® harmless from any violation thereof.
Reference only; do not assemble completely at this time.
Install Seal to Windshield (A) as shown:
To ease installation, soak Seal in hot water before cutting or installing to increase flexibility.
– Install Strut Clamps (E) to Gas Struts (C). – Set aside.
– Install Lower Frame (H) to Windshield (A) with hardware shown.
– Place assembly onto machine and secure Hinges (F) to Frame with hardware
shown.
– Loosely install Strut Clamps (E) around Cab Frame.
– Open Windshield (A) to just under 90° and secure Gas Struts (C) to Lower
Frame (H) with hardware shown.
Extra hands are recommended for following steps:
– Close Windshield (A).
– Ensure that Windshield (A) is aligned to machine and Bulb Seal is in contact
with Dash and Cage Frame as shown.
– Tighten all hardware completely.
Catch (D) installation
install Catch (D) to
Handle
– Close Windshield (A).
– Ensure that Windshield (A) is aligned to machine and Seal is in contact with
Dash.
– Mark location of each Catch (D) onto Dash.
– Open Windshield (A).
– Remove Dash and drill holes where Catch (D) hardware will install.
– Secure Catch (D) with hardware shown. Tighten hardware completely and reinstall Dash to machine.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>