legrand WZ3S3D10 Door/Window Sensor Instruction Manual

: June 5, 2024
: Legrand

legrand WZ3S3D10 Door/Window Sensor Instruction Manual

SAFETY INFORMATION

WARNING: Keep batteries away from children at all times. This product contains a coin/button style cell battery and, if swallowed, can cause severe internal burns within 2 hours of ingesting and can lead to death. Keep away from infants and small children at all times. If battery is swallowed or comes in contact with the inside of the body, immediately seek emergency medical attention. If the battery is replaced with an incorrect size, there is a risk of the battery erupting and causing injury. Dispose of used battery properly. CHOKING HAZARD: Keep batteries and any small parts away from infants nd small children at all times.This item is not a toy and should not be given to children.

INSTALLATION

IMPORTANT:

The distance between sensor and magnet must not exceed 0.8 inch in closed state.
Install indoors.
Use 3/16” drill bit for drywall anchors.

The door/window sensor can be mounted on a door or window. Slide mounting bracket off.

Fix the bracket to door or window with either screws or adhesive tape.

Set Up Your System

This sensor is designed to work with a Zigbe to indicate commissioning mode. If not, press and hold the reset button for 3 seconds. Follow the instructions from your hub to commission the device. If the sensor is enrolled successfully, the LED will stop blinking and stay on for 10 seconds the door or window.
For more information on this product please see this link, or scan the QR code.b https://www.legrand.us/radiant/products/smart- lighting/wz3s3d10.aspx

TROUBLE SHOOTING

Offline After Installation

installation, they may be too far from the Hub. You can try to put them closer to the Hub.
If the door window sensor is not working, make sure the battery has power and it is installed with the“+” side facing up to battery cover. Replace the battery if needed.

Tamper Alarm

When the sensor is removed from the bracket it can trigger the anti-tamper alarm and send out securely attached to the bracket to avoid false

MAINTENANCE

Reset to Factory Settings

Press and hold the pin hole switch for 3 seconds.
The LED indicator will start blinking quickly, the sensor will reset to factory settings and the LED indicator will flash once per second to indicate commissioning mode.

Changing the Batteries

Door/Window Sensor

The app will notify you when a device’ battery gets low. To replace the battery, please disarm the system first to avoid unintended tamper alarm.

Step 1:

Disarm the system.

Step 2:

Remove the door/window sensor from the bracket.

Step 3:

Loosen the screw on the battery cover. Open the battery cover.

Step 4:

Remove the old battery and replace with new CR2032 battery.

Step 5:

Close the battery cover. Replace the screw for the battery cover.

Step 6:

Hang the door/ window sensor on the bracket.

COMPLIANCE INFORMATION

FCC ID: 2AU5D8ASSZEH0 IC: 25764-8ASSZEH0
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

FCC Caution:

Changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

FCC Statement:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the. i• n terference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment
a nd receiver.
t hat to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between
the radiator and any part of your body.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

ISED Statement

This Class [B] digital apparatus complies with Canadian CAN ICES-3(B). Cet appareil numérique de la classe [B] est conforme à la norme NMB-3(B)du Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

LIMITED ONE YEAR WARRANTY

Legrand will remedy any defect in workmanship or material in Legrand products which may develop under proper and normal use within one year from date of purchase by a consumer:
(1) by repair or replacement, or, at Legrand’s option, (2) by return of an amount equal to consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Legrand does not include or cover cost of labor for removal or reinstallation of the
product. ALL OTHER FURTHER ELEMENTS OF DAMAGE (INCIDENTAL

OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED HEREBY. (Some states do not allow disclaimers or exclusion or limitation of incidental or consequential damages, so the above disclaimer and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE ONE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.)

To ensure safety, all repairs to Legrand products must be made by obligation is as follows: (1) Contact Legrand, Syracuse, New York 13221, for instructions concerning return or repair; (2) return the product to Legrand, postage paid, with your name and address and a written description of the installation or use of the Legrand product, and the observed defects or failure to operate, or other claimed basis for dissatisfaction. This warranty gives you to state. l1 legrand® Slide mounting bracket off. n ilLfU hub. The LED indicator will flash once per second and then turn off.
Attach sensor to bracket and affix the magnet to Offline After Installation If sensors are listed as offline in the app after a tamper notification. Be sure that the sensor is notifications.
indicator will flash once per second to indicate system first to avoid unintended tamper alarm.
Changes or modifications not expressly approved by the part equipment off and on, the user is encouraged to try to correct the
Connect the equipment into an outlet on a circuit different from under its specific direction. Procedure to obtain performance of any warranty specific leg