HORNBY HOBBIES HM6000 BLE Model Train Controller Instructions
- June 5, 2024
- HORNBY HOBBIES
Table of Contents
HM6000 BLE Model Train Controller
Instruction Manual
Getting to know the HM6000
Your new Bluetooth circuit controller.
| 
---|---
Initial setup
Your quick step guide
-
Plug in your HM6000 to the track(s).
-
Plug in your transformer to the HM6000.
-
Download the HM | DC application.
A. Scan the QR code with a compatible Android or IOS device
B. On the Hornby website, touch on the relevant app store button.
C. Touch on ‘GET’ or ‘Install’ next to the HM | DC app icon and follow the on- screen instructions.
D. Open the HM | DC application on your device to get started.
-
Connect your HM6000 to HM | DC.
A. Ensure your Power LED is solid ‘Red’, if not refer to Step [2] of ‘Initial setup’.
B. On your compatible device you wish to use, ensure that your Bluetooth is turned on.
C. Open the application and follow the initial setup process, ensuring you allow HM | DC to access and use Bluetooth on your device.
D. Once the initial setup is complete, the Bluetooth connection LED should be solid ‘Blue’.
Getting to know the controls
-
Place an analog locomotive onto the track connected to Circuit ‘1’ of your HM6000.
-
Place yourself with the entire layout in front of you, ensure the HM | DC app is open and you have the ‘Layout’ tab selected.
-
Use your finger to drag the speed slider on Circuit ‘1’ from left to right until your loco is moving.
Note the direction of locomotive travel (left or right?).
-
Does the locomotive direction match the selected directional button on the ‘Layout’ screen of the app? If not, then remove the circuit plug from the power track section, turn it over, and plug it back in. Repeat steps [1] – [4] for each of your other circuits; making sure all of your locomotives travel in the same direction around the circuits, regardless of which way the locomotives are facing.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter, end-users must be provided with transmitter operation conditions for satisfying RF exposure compliance.
Canada Warning
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
collocated or operating in conjunction with any other antenna or transmitter,
End-Users must be provided with transmitter operation conditions for
satisfying RF exposure compliance.
www.hornby.com
Manufactured by:
HORNBY HOBBIES LTD
Westwood Industrial Estate,
Margate, Kent, CT9 4JX,
United Kingdom
+ 44(0)1843 233525
customerservices.uk@hornby.com
This instruction sheet or part thereof may not be copied, duplicated, amended,
or circulated in any form whatsoever without written permission from Hornby
Hobbies Ltd.
© Hornby Hobbies Ltd. Model: HM6000
FCC ID: 2ACUF-HM6000
IC: 12075A-HM6000
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>