CHENSIVE B0CKLDK95B 3 Channel 4K Dash Camera User Manual

: June 13, 2024
: CHENSIVE

Table of Contents

Product Specification
Installation
Product Details
Q and A
Features Introduction
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Dash Cam

CHENSIVE B0CKLDK95B 3 Channel 4K Dash Camera User Manual

Product Specification

DDR	Built-in 64M
FLASH	8M SPI nor flash
Display screen	2.0 inch IPS HD screen
LCD resolution	4K
External port	USB Type-C 5V/2A power adapter port

Max support 64G Class10 TF card Include
2.5mm digital 1080P rear view lens port
Speaker| Monophonic 15*10mm speaker
MIC| 4015 Standard Omnidirectional Microphone

Features

Front camera	6-glass/F2.0aperture/170°wide angle
Inside camera (optiona	VGA 120°
GPS tracker	NO
AV OUT	NO
Rear camera	6M cable/2.5mm port
Photo	Support
Lens rotates	Adjust manually
WDR	Support
HDR	Support
Reversing visual	Support
Video format	AVI
Image format	JPG
Compression format	H.264
Battery	320mAh polymer lithium battery
Language	Support multi-language
G-sensor	Support
Motion detection	Support
Delay shutdown	Support
Loop recording	Support, Do not leak seconds
Sound record	Support
Fill light for night	Support(Open manually)
Parking monitoring	Support
Front camera	4K (30f/s)
In-car camera resolution	1080P
Camera resolution	Max support 3M

Working Environment
Operating temperature| -40°C~70°C
Operating humidity| 15-65%RH
Storage temperature| -40°C~70°C

Installation

How to install the front camera?
( Please install camera after turning off the car engine.）
1.1. Install the driving recorder on the glass near the rear-view mirror
1.2. Connect the power cord to the machine and plug the cord at the intersection of the ceiling and the glass .
1.3. Go down the power cord along the seam of the A-pillar
1.4. Run the power cord along the door seam to the bottom of the storage box
1.5. Run the power cord along the bottom of the storage box towards the cigarette lighter and insert the cigarette lighter plug into the cigarette lighter hole Here are some suggestions for installing the dashcam.
1.1. It should be installed near the rear-view mirror of the car, but not obstructing the driver’s view.
1.2. Make sure that the lens is within the range of the windshield wipers,so that the video can monitor road conditions clearly when it rains.
1.3. Please not touch the lens with your fingers, to prevent fingerprints from affecting the clarity of the video.
1.4. If you need to remove the suction cup holder from the windshield,be careful as it may damage the adhesive and cause the dashcam to fall off.
How to install the rear camera?
(Note: please ensure that the view of the rear camera is normal before installing your rear camera. The length of the rear camera cable is 18ft, supporting car and SUV for five seats. ) There are two installation methods,
2.1. The rear camera is installed above the inner of the rear windshield.
( It can be installed by yourself, the reversing visual function cannot be achieved, and it can only record rear videos)2.2. The rear camera is installed above the license plate frame by a professional or yourself. And connect the camera to the reversing light power supply, which can achieve the reversing visual function. (The red power wire on the rear camera can be connected to the reversing light power supply.)

Product Details

CHENSIVE B0CKLDK95B 3 Channel 4K Dash Camera - Details
1

Q and A

1. How to change front inside rear dash camera views?

In video and photo modes, short-pressing ►, the dash cam can only display 1 or 2 cameras on the screen, Front, Front+Cabin, Front+Rear, Cabin, Inside and Rear are the choices.

2. How to turn on/off the Sound record?

In video and photo modes, short-pressing ◄ to turn on/off the sound record.

3. How to change video, photo and playback modes?

M Button can change video, photo and playback mode short press. And then long press M Button can enter the menu page.

3.1. Short press M to enter Video mode, then long press M to enter video menu settings as follows:

Video Menu

3.2. Short press [M] to enter Photo mode, then long press [M] to enter Photo menu settings as follows:

Photo Menu

1| Resolution| 5M/ 8M/ 10M/ 12M/ 3M/ 2MHD/ 1.3M

3.3. Short press [M] to enter Playback mode, then
Long press [M] to enter Playback menu settings as follows:

Playback Menu

1| Delete| Delete current/ Delete all
2| Protect| Lock current/ Unlock current/ Lock all/ Unlock all

4. How to prevent the SD card from frequently getting full and needing to be formatted?
4.1. When driving normally, please turn off parking monitoring and motion detection. They can occupy storage space and may cause automatic shutdown or freezing of the device. Please turn them on when parking, and configure a voltage reduction line or mobile power supply to retain the electricity.
4.2. Set the G-sensor to 4/8G with low sensitivity. Otherwise, under 2G high sensitivity, There will lock the video just a brake.
4.3. Remember not to press the [M] to lock the video recording during normal video recording.
4.4. Turn on loop recording to automatically overwrite old videos.
4.5. Regularly format the videos to get more storage space.
5. How to stop the camera auto power on and off ?
You can set the “auto power off” menu and choose “off “. (Short press [M] to enter Video mode, then long Press [M] to enter the menu.)
6. How to download the video and image file to computer?
Please remove the SD Card and use an adapter to USB to copy the video to your computer.
7. How can I install the hardwire kit?
After you install the hardwire kit, you needn’t to plug the lighter car charger power cable (Please choose Type C USB port of hardwire kit) Please insert the hardwire kit interface into the power interface of dash cam. And the other end of the hardwire kit is connected to the car battery.
8. What is the use of the red line on the rear camera?
The red power wire on the rear camera can be connected to the reversing light power supply for the reversing visual function.
9. How to use the button to set the function, such as Date/Time setting?
In video or photo mode, long press the [ M] to enter the setup menu.
A n d s h o r t press the [ M] again. Press [►] to choose the date/time, short press the [ OK] to enter date/time menu. Press [◄] and [►] to adjust time details, [ OK] to confirm. Finally, press the [M] to exit. [Please note] Please set the correct time first, in order to effectively record the time of traffic accident for evidence.
10. What type of vehicles is the dash cam suitable for?
The length of the rear camera cable is 18ft, supporting car and SUV for five seats.
11. What other functions do the buttons have?
[ ●] Power button, short press to turn on/off screen, long press to switch on/off the device
[◄], turn on/off the sound record
[►] , change multi views
[M], change the video, photo and playback mode; return button
[OK], stop video recording; take the photo under the Photo Mode; confirm button
[Please note]
If a rear camera is installed and Front+Cabin mode is selected, when the “R” gear is engaged, it will automatically display the complete image of the car’s reversing vision. It will not affect the front car video recording, and will automatically switch back to the front car image after canceling the “R” gear. (The red power wire on the rear camera needs to connect the reversing light power supply.)

Features Introduction

Use the automatic recording function
Start the car engine, the recorder automatically starts to open the recording function.
Close the car engine. The recorder automatically saves the contents of the log and shuts down, recorded video segments are stored on the TF card. When the TF card is full, the recorder will overwrite the oldest recorded image preferentially. (Overwrite must turn on the Loop Recording.)
[Please note] Overwrite must turn on the Loop Recording, loop recording can be set to 1/2/3/5 minutes in the menu.
Use motion detection
In standby mode, enter the menu screen and open the motion detection mode. When the lens is sensitive to the peripheral area of a moving object, the state machine into the camera, recording 30 seconds after the system stops recording.
[Please note] When driving normally, please turn off parking monitoring and motion detection. They can occupy storage space and may cause automatic shutdown or freezing of the device. Please turn them on when parking, and configure a voltage reduction line or mobile power supply to retain the electricity.
G-sensor
With the built-in gravity sensor (G-sensor), if serious vehicle collision, the recorder will lock the first 5 seconds and 10 seconds after the image date when the accident occurred while the bottom left of the display screen displays a lock icon. Locked images will be saved as a special file, the file will not be overwritten cycle.
[Please note] Gravity sensor (G-Sensor) adjustment support needs to set sensitivity at the setup menu, recommend setting the sensitivity to 4/8G.
File playback
In the playback mode, press the [ OK] to play videos. Press the[M] button to exit.
Reversing visual function
First, you must connect the DVR with the car charger, the rear-view camera connect the reversing lights. Insert the car charger, the machine will automatically start recording the status. Screen switch R position in the recording mode automatically switches to the rear-view camera, displaying the reverse image. After reversing the visual machine automatically return to video mode.
[Please note] Please test if rear camera is normal before installation. The red power wire on the rear camera can be connected to the reversing light power supply.
Parking monitor(To achieve unattended surveillance video)
To achieve this function, the dash cam must remain electricity (requires connection of hardwire kit, sold separately), and open the motion detection and parking monitoring function in the menu.
When the dash cam detects a collision while parked, it will automatically turn on and then record a locked video for 30 seconds, and automatically shut down.
[Please note] This function is only used when park stopping. Please turn off the motion detection and stop the monitoring function during normal driving.

FAQ

The machine appears “fileerror’ message| Format TF card. The general problem is TF card
The screen appears with horizontal stripes interference| Please select the correct power supply frequency 50HZ(PAL)
How to properly turn on the 24-hour parking monitoring function Night shooting screen is not clear enough| While normal driving, please do not open. It easily leads to automatic shutdown or crash. Please open park mode when parking. This function requires connecting hardwire kit Recorder shooting depends on the outside strong light source (such as streetlights or car light)
The machine always reverts to the default date and time| You can use car charger or mobile power supply to add power
Why during recording, the machine automatically shut down suddenly| Please turn off the parking monitoring function. Ambient temperature exceeds 70°C will cause automatic shutdown
[Warm note]| Most of the problems with the SD card