SUNSKY EF168 Electronic Pet Fence System User Guide

SUNSKY EF168 Electronic Pet Fence System

Please read this entire guide before the operation

WARNING

Please charge the collar receiver before put it into training! If the collar receiver doesn’t work for a long time, you should charge it fully, and charge it every month then keeping it idle.

Product Description

This electronic pet fence system EF168 is reliable, cost-efficient pet containment systems. The harmless radio signal was issued by the transmitter and go through the wire to be the boundary of the “yard”, when your dog approaches the boundary beyond setting range, the receiver collar in dog neck will start up with a warning beep at first. If your dog keep running to the boundary, the receiver will issue static shock with gradually stronger intensity until your dog returns back to the “safe area”- within the boundary you set up.

Main feature

This product has three levels of function adjustable: the first level is only the vibration function, the second level is weak static shock function, the third level is strong static shock function. There is a warning beeper prompt for each level.

1. The function vibration or shock When the dog is closer the boundary the vibration or shock will be stronger.
2. Beeper A warning tone will be issued twice and then shock or vibration if your dog continues to move closer to the boundary;
3. Variable Field Width Control: Allows you to precisely control the width of the signal field; the cable is aabout 200M
4. Audible and Visual Wire Break Indicators: Once the boundary wire was broken, the transmitter’s loud sonic alarm will issue with a flashing light;
5.  Speed Detect Anti-Run through The faster your dog is moving, and the higher level of shock or vibration intensity is issued.
6. Multipale Collar Operation: Add as many collars as you like to contain as many animals as you have. There is no limit to the number of collars it can control.
7. Up to 5000 square meters range (over 1.24 acre).

Package Contents

• Transmitter * 1;
• Collar Receiver * 1;
• TPU strap • 1;
• Rubber Probes • 2;
• Test Light Tool • 1;
• Screws * 2;
• English Manual * 1;
• Charger • 1;
• 200-meter Wire • 1;
• Boundary Flags * 20;

Installation of fence system

To make sure the normal operation of the fence system, you should design a diagram of the fence system at first. Then mount the transmitter nearby the AV outlet, set the boundary with wire and flags, place the receiver collar into neck of your dogs. Please install the system as below steps:

Step 1: Mount the transmitter
To make transmitter work properly, you should ensure, there is a 110/220VAC outlet nearby before mounting it. Place the transmitter at a wall or tree and fixed it with screws.

Step 2: Install the boundary flags and Connect the wire
Connect one terminal of the wire to the transmitter firstly, mount the boundary flags one by one according to the boundary layout, and make sure the wire go through the hole of flags meanwhile. Until all the flags has been mounted properly along the boundary and come back to the transmitter. Please keep the excess wire around the bobbin and connect the terminal of wire to transmitter.

Notice
the packed. wire length of is 200 meters. you can add more. (must use the wire that we provide)

Step 3: Set parameters for the transmitter
Pushing ON/OFF button to turn on/off the transmitter. The signal field is the distance from the wire to the place where the collar receiver first activates. the value of power level is bigger and the control range is bigger. Press ON/OFF button to turn on the transmitter, press can adjust the control range. can decrease the control range, press the control range.

Set the transmitter signal power level

Verify the function of fence system
This product has three levels of function adjustable: the first level is only vibration function, the second level is weak static shock function, the third level is strong static shock function. (There is a warning beeper prompt for each level.) Press the button on the transmitter and to change the control range. According to the comparison table above, such as: level 10. and then take the collar receiver to right location as the right control range. Press ON/OFF button of collar receiver to power it on and move the collar to the boundary wire. If the warning tone of “bi-bi” and vibration are issued or bi- bi” and shock are issued, and then place the LED test light on the collar contact probes, the LED should light on in a few seconds (It’s means the shock function is good). If you move the receiver collar away from the boundary, the receiver will stop “bi-bi” and vibration or shock. Notice: Don’t place the receiver collar on your dog until the fencing system has been tested and the signal field adjusted. You must manually test the containment system to verify that the signal is properly transmitted trough the wire. Use the supplied test light.

Put the receiver collar on your dogs
Place the collar around the dog’s neck with the receiver box under the chin. The collar must be on relatively tight to keep the probes making shin contact without restricting breathing. You should be able to slide only one finger under the strap at the back of dog’s neck. Please check the skin of the dog’s neck every day, if the dog’s neck has any adverse reactions, you must stop use this collar on dogs’ neck. If the erythema is caused by too long wearing time or too tight collar, it needs to use it after recovery.  always make sure the collar is functioning properly before putting it on the dog.

Receiver button and function:

1.  Long press for ON/OFF
2. Setting function of receiver collar: the first level is only vibration function, the second level is weak static shock function, the third level is strong static shock function. (There is a warning beeper prompt for each level.) It’s with function vibration + beeper when the collar ON and the light on receiver collar flashing continuously one time;  It’s with function weak shock and beeper when press twice ON button and the light on receiver collar flashing continuously two times;  It’s with function strong shock and beeper when press three times ON button and the light on receiver collar flashing continuously three times; if you continue press ON button, the collar will cycle function. If receiver collar is flashing light red(.0.5S flashing one time), it’s with low battery, and now you need charge for it.
3.  It flashing light double red when charging, it light on green when full charge, turn off the charge it return to shutdown status.
4. .Receiver collar will automatic go to standby when collar stationary 60S (power save function), and then shake the collar will be go to work.
5. The receiver collar works: 20S continuous electric shock + 5S stop work, and then stop shock after 5 cycles, flashing red light until dogs return to safety area.

How the correction works

1. Pre-correction Warning Tone: When the dog reaches the edge of the signal field in the yard, it will hear a warning tone, if dogs don’t return to safe area, the receiver collar will shock or vibration continuously until dogs return to safe area. If dogs return to boundary again, the receiver collar will work shock or vibration again.
2. Run-Through Prevention: The receiver collar automatically increase the correction as the dog enters the signal field, tone beeper, vibration and shock will be stronger when dogs closer boundary. Strong shock or vibration will not allow dogs go beyond the setting range.

System maintenance tips
In fact, very little maintenance is required for this receiver collar, since the receiver collar is rechargeable and waterproof, but the transmitter is not waterproof and must be protected from the weather. A close lighting strike may damage the unit. Unplug the transmitter and disconnect the wires during storms. Test the system once a week to make sure the receiver collar is working properly. Also testing the system will verify the field width setting is correct. To test, attache the LED test light to the receiver collar probes. Holding the receiver by the case( NOT by the probes), walk into the signal field and pay attention to the warning tone and LED light. The dogs closer boundary and shock or vibration will be stronger.

 Troubleshooting Guidelines

Dog is not responding to correction, pay attention below points: Check the collar strap and make sure it’s proper tightness.  Trim the dog’s hair or use rubber probes to make better skin contact. 3、If receiver collar is low battery, charge it.System Test Procedure: Whenever you experience a malfunction, you will need to do a Test Loop to determine which component- collar, wall transmitter, or yard wire-is not working. To perform the Test Loop procedure:
.Make a test loop using a piece of wire at least 4meters in length. 2. Remove the existing wire from your wall transmitter.  Insert the two ends of the test loop wire into the wall transmitter. hand, move outside the field and approach the test loop. Make a mental note of the distance between the collar and the wire when the collar activates, Set the transmitter signal level to a medium value, such as level 4, back away from the wire and approach it again, determine the distance should be geater on the medium range setting..If more than one collar receiver is used with the system, repeat the above test on each collar.

Important Tips

1. This model wire fence electronic is only for pet dogs;
2.  When the receiver collar is with low battery, it will intermittently work, and you need to stop working please.
3. .Don’t wear the receiver collar on dog’s neck more than 10 hours each time.
4. .Keep the receiver collar away from your child to avoid accidental injury.
5. .Please read the manual carefully before using it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>