ProXes VCM 25 Woonsocket Instruction Manual
- June 5, 2024
- ProXes
Table of Contents
ProXes VCM 25 Woonsocket
OVERVIEW
CHASSIS UNIT
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 | Cyl. Grooved Dowel Pin | 0144 | 0144 |
| 2 | Nylon Wheel (uses 2) | 0142 | 0142 |
| 3 | Bolt for the Wheel (12 x 55) | 0143 | 0143 |
| 4-5 | Bowl Bumper (need p/n 6710 screw) | NLA | NLA |
| 6 | Rubber Foot (uses 4) | 0141 | 0141 |
| 7 | Chassis | NLA | NLA |
| 8 | Rubber Bumper | NLA | NLA |
| 9 | Phillips head screw M6 x 60mm | 6710 | 6710 |
| 10 | Washer 6 mm | 7001 | 7001 |
| 11 | Lock Pin with Chain | 0140 | 0140 |
| 12 | Square Head Bolt M10 x 20mm | 7038 | 7038 |
| 13 | Bowl Lock Handle/Lever | 0161 | 0161 |
| 14 | Knob for handle | 1512 | 1512 |
| 15 | Shim Washer 1.0mm thick | 0159 | 0159 |
| 16 | Shim Washer 2.0mm thick | 0160 | 0160 |
| 17 | Bowl Swivel Bearing –right hand | 0157 | 0157 |
| 18 | O-ring | 0158 | 0158 |
| 19 | Bushing – Oilite –right hand | 0154 | 0154 |
| 20 | Disc – positioning | 0155 | 0155 |
| 21 | Bushing – Oilite –left hand | 0154 | 0154 |
| 22 | O-ring | 0158 | 0158 |
| 23 | Bowl Swivel Bearing –left hand | 0153 | 0153 |
| 24 | O-ring | 0152 | 0152 |
| 25 | Cable Sleeve | 0149 | 0149 |
BOWL COVER UNIT
| ILLUS # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 & 2 | Mixing Baffle | NLA | NLA |
| 3 & 4 | Gasket for lid/cover (Silicone) | 0202 | 0203 |
| 5 & 6 | Cover for Bowl | NLA | NLA |
| 7 & 8 | Cover for Bowl w/o insp. Opening | NLA | NLA |
| 9 | Lock Plate | 0212 | 0212 |
| 10 | Shim for Lock Plate | 7013 | 7013 |
| 11 | Screw – Flat Head M6 x 15mm | 7014 | 7014 |
| 12 | Stud M10 x 55 | 7015 | 7015 |
| 13 | Nut Hex M10 | 7010 | 7010 |
| 14 | Retainer for Sight Cover | 0213 | 0213 |
| 15 | Knob for Sight Cover | 1512 | 1512 |
| 16 & 17 | Sight Cover | NLA | 0215 |
| 18 | Crank Handle | 0220 | 0220 |
| 19 | Retaining Screw for crank | 0221 | 0221 |
| 20 | Acorn Nut M8 for knob on crank handle | 0219 | 0219 |
| 21 | Handle (knob) for crank handle – | 0218 | 0218 |
| 22 | Knob for Sight Cover | 0217 | 0217 |
NEW STYLE BOWL SEAL EXECUTION
NEW STYLE BOWL UNIT
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 | Bowl W/ adapter | NLA | NLA |
| 2 | Bowl W/ adapter | NLA | NLA |
| 3 | Wing Bolt M6 x 15 | 0175 | 0175 |
| 4 | Bolt for the locking handle | 0174 | 0174 |
| 5 | Locking Handle | 0176 | 0176 |
| 6 | Pin | 7004 | 7004 |
| 7 | Roller | 0177 | 0177 |
| 8 | Knob for locking handle | 1512 | 1512 |
| 9 | O-ring 75×5 | 0181 | 0181 |
| 10 | Bowl Seal Assembly with O-ring | 3kp000-23 | 3kp000-23 |
| 11 | Wing Nut | 6837 | 6837 |
| 12 | Pressure Ring | 0187 | 0187 |
| 13 | Slant Ring Set with Pins | 0189 | 0189 |
| 14 | Knife Shaft Subassembly | each item sold separate | |
| 15 | Pin – Long | 0191 | 0191 |
| 16 | Pin – Short | 0190 | 0190 |
| 17 | Knife Shaft | NLA | 0193 |
| 18 | Flathead Screw M6 x 10mm | 7005 | 7005 |
| 19-20 | Torsion Spring for cover | 0168 | 0168 |
| 21 | Sleeve for hinge shaft | 0167 | 0167 |
| 22 | Hinge bolt/shaft | 0166 | 0166 |
| 23 | Holder Bumper | 0171 | 0171 |
| 24 | Spacer | 7007 | 7007 |
| 25 | Bumper for bowl | NLA | NLA |
| 26 | Threaded Pin | 0178 | 0178 |
| 27 | Lock Washer 10.2 | 7009 | 7009 |
| 28 | Hex Nut M10 | 7010 | 7010 |
BOWL UNIT
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 | Hexagon nut | 7197 | 7197 |
| 2 | Flat washer | 7198 | 7198 |
| 3 | Bowl VCM 25 | NLA | na |
| 4 | Bowl VCM 40 | na | NLA |
| 5 | NLA | NLA | |
| 6 | Bolt for locking lever | 0174 | 0174 |
| 7 | Locking lever | 0176 | 0176 |
| 8 | Grooved pin | 7004 | 7004 |
| 9 | Roller | 0177 | 0177 |
| 10 | Knob | 1512 | 1512 |
| 11 | Oil seal | 0162 | 0162 |
| 12 | Rubber Gasket | 0163 | 0163 |
| 13 | Retainer plate f. oil seal | 0164 | 0164 |
| 14 | Cap gasket | 0165 | 0165 |
| 15 | Holding plate | 0179 | 0179 |
| 16 | Wing nut | 6837 | 6837 |
| 17 | Pressure ring w. pin | 2241 | 2241 |
| 18 | Slant ring set w. pins | 0189 | 0189 |
| 19 | Short pin | 0190 | 0190 |
| 20 | Long pin | 0191 | 0191 |
| 21 | S.S. Knife shaft | 6826 | 6826 |
| 22 | Acorn nut | 0219 | 0219 |
| 23 | Holder for cover spring | NLA | NLA |
| 24-25 | Lid spring | 0168 | 0168 |
| 26 | Counter-sunk screw | 7005 | 7005 |
| 27 | Sleeve for cover spring | 0167 | 0167 |
| 28 | Cover hinge bolt | 0166 | 0166 |
| 29 | Holder for buffer VCM 25 | NLA | NLA |
| 30 | Holder for buffer VCM 40 | Na | 0171 |
| 31 | Buffer | NLA | NLA |
Installation Instructions
For Shaft Seal Assembly
- Disconnect unit from the electrical power supply.
- Remove knife shaft assembly.
- Use a seal spanner wrench (Fig. 1) to remove the existing seal. Make sure bowl threads and seal areas are cleaned and free of any foreign material.
- Prepare a new seal (1, Fig. 2) for installation by using the Dow Corning 111 compound from the seal kit. First cover the exposed area of the “0” ring (2, Fig. 2 and 3, Fig. 3) with the compound Next use this sealing compound to fill the seal cavity (2, Fig. 3). Now place a film of the lubricant on the lip of the seal (1, Fig. 3)
- Inspect shaft sleeve (4, Fig. 3) for wear grooves or a build-up of foreign material. Clean or replace if necessary. apply a coat of #111 grease to the entire surface of the sleeve.
- Assemble the new seal hand-tight. Be extreme ly careful not to damage the seal when sliding the seal onto the motor shaft and also make sure the seal and bowl threads are properly aligned.
- Tighten new seal with the spanner wrench (Fig.
ACCESSORIES & TOOLS
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 | Knead / Mix Shaft | NLA | |
| 2 | Knead / Mix Shaft | 0377 | |
| 3 | Grater Shaft | 0308 | |
| 4 | Grater Shaft | 0309 | |
| 5 | Mix Shaft –Large Qty | 0310 | |
| 6 | Mix Shaft –Large Qty | 0312 | |
| 7 | Set of 2 wide knives | 0295 | |
| 8 | Set of 2 wide knives | 0296 | |
| 9 | Set of 2 (Wide) Wave Cut Knives | 0299 | |
| 10 | Set of 2 (Wide) Wave Cut Knives | 0300 | |
| 11 | Set of 2 (Wide) Narrow Cut Knives | 0301 | |
| 12 | Set of 2 (Wide) Narrow Cut Knives | 0302 | |
| 13 | Set of 2 narrow knives | 0297 | |
| 14 | Set of 2 narrow knives | 0298 | |
| 15 | Set of 2 low angle knives | 0303 | |
| 16 | Set of 2 low angle knives | 0304 | |
| 17 | Winged Nut Accessory | 0185 | 0185 |
| 18 | Attach. Power Unit | NLA | |
| 19 | Attach. Power Unit | 0318 | |
| 20 | Strainer Basket | NLA | |
| 21 | Strainer Basket | NLA | |
| 22 | Wrench for Knife Shaft | 0238 | 0238 |
| 23 | Sharpening Tool | 0237 | 0237 |
| 24 | Peg Wrench (takes off nut on mixing baffle) | 0234 | 0234 |
| 25 | Spanner Wrench for knurled nut | 0236 | 0236 |
| 26 | Spanner Wrench for bowl seal | 0182 | 0182 |
SWITCH UNIT
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 | Hex. Head M6 x 25mm Retaining Screw | 7517 | 7517 |
| 2 | Knob for switch handle | 1512 | 1512 |
| 3&4 | Switch Handle | 0228 | 0228 |
| 5 | Rubber Gasket for Switch | 0226 | 0226 |
| 6 | Insulator 460 V, pertinax plate | 0225 | 0225 |
| 7 | Screw M6 x 10mm | 7085 | 7085 |
| 8 | Oil Seal | 0229 | 0229 |
| 9 | Drum Switch | 0224 | 0224 |
| 10 | Switch Housing | 0223 | 0223 |
| 11 | Screw M6 x 15mm | 7086 | 7086 |
| 12 | Hex Head Bolt M6 x 20mm | 7087 | 7087 |
| 13 | Seal Disc – Cord -cable sealing disc only for VCM | 0230 | 0230 |
| 14 | O-ring | 0152 | 0152 |
| 15 | Cord (Power cord is an 8gg 10-4 gauge wire s/o cable) | NLA | NLA |
| 16 | Plug – Hubbel “Twist Lock” | NLA | NLA |
| 17 | Switch Housing Subassembly | Each part sold separate | |
| 18 | Switch Housing Subassembly | Each part sold separate | |
| 19 | Hex Nut M8 | 7031 | 7031 |
| 20 | Washer M8 | 7034 | 7034 |
| 21 | Hex Head Bolt M8 x 35mm | 7093 | 7093 |
| 22 | Grd. Lug- Cord | NLA | NLA |
| 23 | Fitting for Cord -cable glant with tension relief | 0232 | 0232 |
| 24 | Armored Cable – protective hose | 0222 | 0222 |
| 25 | Clamp for Cord (not shown) | 7095 | 7095 |
MOTOR UNIT
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 1 | Flathead screw M5 x 8mm | 7023 | 7023 |
| 2 | Shaft Sleeve | 0265 | 0265 |
| 3 | Water Spin Off Disc w/ screw | 0264 | 0264 |
| 4 | Socket head screw M6 x 25mm | 7022 | 7022 |
| 5 | Bearing Upper Bracket | 0267 | |
| 6 | Bearing Upper Bracket | 0268 | |
| 7 | Pin 10 x 60mm | 0262 | 0262 |
| 8 | Knurled Nut | 0260 | 0260 |
| 9 | Upper Bearing – newer style/sealed | 6226 | 6226 |
| Upper Bearing – old style / needs oil seal | 6109 | 6109 | |
| 10 | Oil Seal for old style bearing | 6175 | 6175 |
| 11 | Rotor | 0269 | |
| 12 | Rotor FD 132 s 25-2/4 | 0270 | |
| 13 | Retainer Bearing | 0277 | 0277 |
| 14 | Retaining Ring | 0278 | 0278 |
| 15 | Lower Bearing | 6085 | 6085 |
| 16 | Lower Bearing Bracket | 0279 | |
| 17 | Lower Bearing Bracket | 0280 | |
| 18 | Lock Washer | 7026 | 7026 |
| 19 | Hexagon Head Screw M5 x 45mm | 7027 | 7027 |
| 20 | Retainer – bearing | 0277 | 0277 |
| 21 | Fan | 0286 | |
| 22 | Fan | 0287 | |
| 23 | Retaining Ring | 0288 | 0288 |
| 24 | Retaining Ring | 0278 | 0278 |
MOTOR UNIT
| ILLUS. # | STEPHAN PART DESCRIPTION | VCM 25 | VCM 40 |
|---|---|---|---|
| 25 | Motor Housing | 0292 | |
| 26 | Motor Housing – FD 112 / FD 132 | 0241/0293 | |
| 27 | Vent Housing | 0290 | |
| 28 | Vent Housing | 0291 | |
| 29 | Washer M6.4 | 2657 | 2657 |
| 30 | Lock Washer B6 | 7029 | 7029 |
| 31 | Hexagon Head Screw M6 x 15mm | 7086 | 7086 |
| 32 | Hexagon Nut M8 | 7031 | 7031 |
| 33 | Lock Washer B8 | 7034 | 7034 |
| 34 | Key | 0284 | |
| 35 | Key | 0285 | |
| 36 | Hexagon Nut | 7033 | 7033 |
| 37 | Screw – Lock | 0283 | |
| 38 | Screw – Lock | 0283 | |
| 39 | Stator 230 Volt, 60 Hz, 3 Phase | 0272 | |
| 40 | Stator 200 Volt, 60 Hz, 3 Phase | 0271 | |
| 41 | Stator 460 Volt, 60 Hz, 3 Phase | 0273 | |
| 42 | Stator 230 Volt, 60 Hz, 3 Phase | 0275 | |
| 43 | Stator 200 Volt, 60 Hz, 3 Phase | 0274 | |
| 44 | Stator 460 Volt, 60 Hz, 3 Phase | 0276 | |
| 45 | Lock Washer B8 | 2034 | 2034 |
| 46 | Washer M8.4 | 7035 | 7035 |
| 47 | Hexagon Head Bolt M8 x 60mm | 7036 | 7036 |
| 48 | Hexagon Head M8 x 20mm | 7037 | 7037 |
RECOMMENDED SPARE PARTS LIST
Documents / Resources
|
ProXes VCM 25
Woonsocket
[pdf] Instruction Manual
VCM 25 Woonsocket, VCM 25, Woonsocket
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>