Dongguan Jiufeng Hardware Plastics 69808806 Bunk Shelf with Wireless Charger Instruction Manual
- June 6, 2024
- Dongguan Jiufeng Hardware Plastics
Table of Contents
Dongguan Jiufeng Hardware Plastics 69808806 Bunk Shelf with Wireless Charger Instruction Manual
SKU# 69808806 / ITEM# 3145301
Bunk Shelf with Wireless Charger
BUNK SHELF
STEP 1 : Affix the clamp to your ideal position of the bed frame.
STEP 2 : Adjust the rotary knob to tighten the clamp.
- This product is for household use only.
- This product is to be mounted to the bed frame.
- Maximum loading capacity: 20 lbs
WIRELESS CHARGING
- 10-watt maximum wireless charger supports most smart phones, tablets and other compatible Qi-enabled devices. Check your device manual for compatibility.
Specification input: DC 9V/1.7A
Wireless charging output: 5V/2A
Charging distance: 1 ~ 5 mm
Connect the AC adapter to DC jack on the wireless charger, and plug into outlet.
Place Qi compatible device face up on the charging pad. Charging status will be indicated as per below:
- Blinking blue light: Charging pad connects to power. Light will shut off after 5 seconds.
- Solid blue light: Device is charging.
- Blinking red light: Foreign object on the charging pad or device is not charging. Please remove foreign object or reposition the device.
CAUTION: Remove any metal protective case before charging your phone. Do not place magnetic or metal objects on charger during charging. Qi compatible phones with metallic looking finishes will charge normally.
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there isno guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Wireless charger manufacturer
Adapter manufacturer
Produced and assembled by Dongguan Jiufeng Metal and Plastic Manufacturing
Ltd.
www.bedbathandbeyond.com
www.bedbathandbeyond.ca
SAVE THESE INSTRUCTIONS
Customer service
IMPORTANT SAFETY INFORMATION
- Remove the credit cards and other cards with magnetic strips to prevent damage to them.
- Keep the charge away from extreme heat and direct sunlight.
- Do not modify or repair this device.
- Do not use in high temperatures or extreme weather.
- Do not use chemical detergents to clean your device, use a soft dry cloth.
- Immediately unplug it from its power source if it gets wet.
The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 12cm between the radiator and your body.
The device has been evaluated to meet general RF exposure requirement. To maintain compliance with RSS-102 — Radio Frequency (RF) Exposure guidelines, this equipment should be installed and operated with a minimum distance of 10cm between the radiator and your body
This device contains licence-exempt transmitters that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.