devolo Giga Bridge Connecting ONT and Router Installation Guide

June 3, 2024
devolo

devolo logo

Installation
devolo Giga Bridge
Connecting ONT and router

Giga Bridge Connecting ONT and Router

Installation videos / Manual

www.devolo.global/giga-bridge-install

| Videos with step-by-step installation of the devolo Giga Bridge.
---|---
Manual for more detailed instructions.

The devolo Giga Bridge is intended solely for use on cleared – exclusively available – telephone or coaxial cables. The free availability of the lines without third-party devices must be determined before connecting the devolo Giga Bridge.

**Pairing of devolo Giga Bridges

**

Connect both devolo Giga Bridge adapters to an available power socket. The LEDs of both adapters flash white. Carry out the next installation step within 3 minutes.

devolo Giga Bridge Connecting ONT and Router - fig

Connect the two devolo Giga Bridge adapters to the phone sockets using the network cable supplied.
A new devolo Giga Bridge network is automatically set up (pairing). When both LEDs light up white continuously, the process is complete and you can remove the network cable again.

devolo Giga Bridge Connecting ONT and Router - fig 1

The devolo Giga Bridge uses G.hn technology for the transmission of the Internet signal over coaxial (TV/SAT) or telephone line. In scenario “a” (as of p. 9), the G.hn signal is transmitted over two telephone wires or in scenario “b” (as of p. 15) via standard coaxial cable.

devolo Giga Bridge Connecting ONT and Router - fig 3

The telephone cable is removed from the demarcation point and then split and secured by means of connection technology involving wire stripping and soldering or screwing down. A standard network interface is created as a result. Note the correct pin assignment: Pin 4/5 for SISO.

devolo Giga Bridge Connecting ONT and Router - fig 4

Telephone cabling

Connect the devolo Giga Bridge adapter to the existing wall connection (CAT RJ 45 box) via the phone socket. Use the provided telephone cable for this purpose. Now connect the devolo Giga Bridge to the NT/ONT-Box using the provided network cable.

devolo Giga Bridge Connecting ONT and Router - fig 10

Connect the second devolo Giga Bridge adapter to the WAN (Wide Area Network) port of the router using the provided network cable. Now use the telephone cable to connect the devolo Giga Bridge (Phone socket) to the wall connection. Done!

devolo Giga Bridge Connecting ONT and Router - fig 5

Connect the devolo Giga Bridge adapter to the existing coaxial cabling. To do this, use the provided cable and connect it to the coaxial socket (Coax) of the Giga Bridge. Connect the devolo Giga Bridge to the NT/ONT-Box using the provided network cable.

devolo Giga Bridge Connecting ONT and Router - fig6

Connect the second devolo Giga Bridge adapter to the WAN (Wide Area Network) port of the router using the provided network cable. Connect the devolo Giga Bridge to an existing connection in the wall via the F-type socket (Coax). Done!

devolo Giga Bridge Connecting ONT and Router - fig8

G.hn button

Duration of the
button press| Action| LED behaviour
---|---|---
1 second| Start pairing with other devolo Giga Bridge adapters| Flashes white

10 seconds| Reset devolo adapter to factory settings| Lights up red
G.hn LED| The devolo Giga Bridge adapter …| LED behaviour
---|---|---
| … is working perfectly. It is connected to other devolo Giga Bridge adapters.| Lights up white
| … is currently establishing a pairing connection with another adapter.| Quickly flashes white
| … is not connected to the network*| Slowly flashes white
| … is in standby mode.| Alternately flashes white and red
| … is currently undergoing a software update.| Flashes red
| … has a poor G.hn connection.| Lights up white and then briefly flashes red
| … is currently in the start-up process.
… cannot see any other devolo Giga Bridge adapters.| Lights up red
| … no longer has any LED function since it was disabled by the user.| None

Support

www.devolo.global/help

Warranty: 3 years
If your devolo device is found to be defective during initial installation or within the warranty period, please contact the vendor who sold you the product. The vendor will take care of the repair or warranty claim for you. The complete warranty conditions can be found at www.devolo.global/warranty.

devolo logoGiga Bridge
Device 1 password
Device 2 password
devolo AG · Charlottenburger Allee 67 · 52068 Aachen · Germany
www.devolo.global

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals