ETOE A1191 WiFi Bluetooth Projector User Manual

June 5, 2024
ETOE

ETOE A1191 WiFi Bluetooth Projector

Safety Instructions

Read and understand all instructions before you use this device. Do not make any changes or settings that are not described in this manual. Any physical injury, and loss of data or damage caused by failure of following instructions, is not included in the warranty.
Setup
To reduce the risk of fire and/or electric shock, do not expose the device to rain or moisture, and objects flled with liquids, such as vases, should not be placed on the device. Do not place the device on soft surfaces such as tablecloths or carpets a doing so could be a fire hazard. Do not place the device In areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field. To prevent overheating, do not block or clog the ventilation openings. Never place the device in a confined space. Always leave enough space around the device for ventilation.Protect the device against direct sunlight, heat, large temperature fluctuations and moisture. When the device runs for a long period of time and the surface becomes hot shut t dawn and unplug the power cord. Resume operation only after the device has cooled. Always handle the device with care. Avoid touching the lens. Never place heavy or sharp objects on the device or the powar cord. To avold electric shock, do not disassemble. Only use attachments or accessories specified by the manufacturer. Avoid extreme vibration. t may damage the internal components. Do not allow children to handle the device without supervision. Under the following conditions, a layor of moisture can appears inside the device which can lead to malfunctions:  if the davice is moved from a cod to a warm area;  after a cald room ls heated;  when the device is placed in a damp room. To avoid any moisture, seal the device in a plastic bag before moving it to another room, and wait for one to two hours before you take it out of the bag.

Power Supply
Use only the provided power adapter Power off the device before removing the power supply from the socket. Protect the power cord from being walked on ar pinched, particularly at plugs, convenience receptacles, and the point where they exit from this device. Unplug thle device lf there are lighting storms or when unused for a long period of time. Where the power plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Before you make or change any connections, ensure that all devices are disconnected from the power outet Never touch the power cable or the power connector with wot hands.

Hearing Safety
To avoid hearing damage, do not listen for extended periods at high volume. Set the volume at a safe level.
Cleaning
Power of the device and remove It from the power supply before cleaning the surface. Use a soft, Int-free cloth. Never use liquid, gaseous, or easly flammable cleansers (ike sprays, abrasives, polishes, and alcohol). Do not use any liquid cleaning agents to olean the lens as they may damage the protective coating on the lens. Wipe over the surfaces gently. Be careful that you do not scratch the surfaces. Use lens cleaning paper to clean the lens of the projector.

Repairs
Do not make any repairs to the device by yourself. Only have your device repaired by an authorized service center Improper maintenance can result In Injuries or damage to the device. Refer all servicing to qualified service personnel. Caution: Possibly hazardous optical radiation is emitted from this device. Do not stare at the operating beam. The bright ght may hurt yaur eyes.

What’s includedETOE-A1191-WiFi-Bluetooth-
Projector-1

Overview

Projector

  1.  On/Off button
  2.  IR Receiver
  3.  Tripod Screw Hole
  4.  Pads
  5.  19V DC Input
  6.  USB2.0
  7.  HDMI14
  8.  Led Indicator
  9.  IR Receiver
  10. 3.5mm AUX Port

Remote

ETOE-A1191-WiFi-Bluetooth-Projector-4

  1. Indicator
  2. On/O
  3. Keystone+
  4. Keystone
  5. Focus t
  6. Focus
  7. Next
  8. Input Signal Resource
  9. 4 Navigation Buttons
  10. OK
  11. Menu
  12. Return
  13. Volume+
  14. Volume
  15. Mute

Get started

Placement
Place ETOE Projector A1191 on a stable, flat foundation in front of the protective surface. For the best results, the projection surface should be white and flat. It la unnecessary to tlt the projøctor towards the projection surface. You can correct the projection image with the built-in keystone connection and with remote control. The distance between the projector and the projection surface determines the image size.
Prepare the Remote Control
Prepare a 2xAAA battery, which is not included in the box To replace the battery, slide off the battery bak cover to open the battery compartment, insert new batteries (matching the polarity (+4) Indicated), and close the battery compartment

power onETOE-A1191-WiFi-Bluetooth-Projector-5

  1.  AutomaticConnect the Included adapter to the DC-n port af the projector.
  2.  Connect the AC cord to the adapter.
  3.  Plug the adapter to the outlet and the LED Indicators will Right on.
  4.  Press the On/Of button, Walt the projector to tum an.

Focus

  1.  Place the projector towards a suitable projection surface or wall, adust the distance for proper size of picture.
  2.  Use the Remote control [Focus+] or [Focus-] until the picture ls perfectly clear. Note: The screen size must between 40″ to 200.

Keystone correction
ETOE projector A1191 supports automatic vertical keystone correction and remote four-point keystone correction.

  1.  Place the projector towards a suitable projection surface or wall, and adjust the distance for proper size of the picture.
  2.  Focus the picture perfectly clear.
  3.  If your projector Is directly toward the projection surface, but pointing up and down, the picture wll be adjusted automatically. You can stll use remote control keystone+] or [keystone-), or go to Projection Setting>Four point correctian] for further minor ad ustment, tll the picture Is perfectly rectangular,ETOE-A1191-WiFi-Bluetooth-Projector-6ETOE-A1191-WiFi-Bluetooth-Projector-6
  4. If your projector Is not vertical to the projection surface, use remote control, go to Projection Setting-Four point corection].ETOE-A1191-WiFi-Bluetooth-Projector-7
  5. Press [OK] to select the point, 4Navigation button] to adjust, until the picture Is perfect rectangular

Settings

Go through the set-up process when you tum on the projector for the first time.

Projection setting
Installation mode Desktop Front Projection: The device is located in front of the projection surface. Desktop Rear Projection: The device is located behind the projection surface. [Cellng Front Projection: The developed ls hanging from the ceiling In an upside-down position. The Image ls rotated by 180 degrees. Ceiling Rear Projection: The device is hanging from the ceiling in an upside-down position behind the projection surface. The image is rotated by 180 degrees and horizontally mirrored.

Zoom
Zoom in or out from 50%-100% to fit image size in certain scree. Vertical correction Vertical keystone connection from 0-100. Horizontal connection Horizontal keystone correction from 0-100. Four-point Correction Use the remote control, [OK] to select the point, 4 [Navigetlon button] to adjust, [Beck] to ext.

Network
This projector can be connected to the Internet via a wireless(Wi-Fi) connection.

  1.  Go to the home page, select [Bettingel> [Nebwork eetting] and press.
  2.  Follow the on-screen instructions to complete the network connection.

Bluetooth
You can connect a Bluetooth headphone or speaker to ETOE Projector A1191.

  1.  On the home menu, select [Settinge]> Bluetooth] and press.
  2.  Follow the on-screen Instructions to complete the Bluetooth connection.

Other settings
Boot signal source HDM/[USB]/[o Select default display signal source from HDMI, USB, or turn to home page.No need switch signal source every time when the projector is turned on. Language setting Select your language from Engilsh). [Deutsch), [Ftançals]. [tallano], Espafol, [EAEI, IEO. Restore factory setting Reset your device and restore the factory setting.

Using the ETOE projector A1191

Connect to an HDMI playback device
This projector supports connections with various HDMI playback devices such as PC, TV stick, TV box, DVD player, set-top box (STB), game console or other devicas.

  1. Connect this projector to an HDMI playback device with an HDMI cable (not provided).
  2.  Press the signal source button on the remote, or click the Signal Source button at the homepage, select HDMII, and presa. Ft will automatically start the HDMI playback when connected to an HDMI playback device)

Connect to a USB storage device
With this projector, you can enjoy music, video, and pictures, that are stored on a USB storage device.

  1.  Plug-In the USB storage device.
  2.  Prees the slgnal source button on the remote, or click the Signal Source butt n at homepage, salect [USB], and pres.
  3.  Select the file you plan to play from the file and folder menu.
  4.  Press [oK| to start playing.

Connect to Bluetooth headphones or speaker
You can connect a Bluetooth headphone or speaker to ETOE Projector A1181.

  1. On the home page select [Settings]> Bluetooth] and prese.
  2.  Follow the on-screen Instructions to complete the Bluetooth connection.

Connect to a headphone vie AUX cable
You can connect a headphone or speaker to ETOE Projector via AUX cable as well.

  1. Plugin the 3.5mm AUX cable connector to the ETOE projector AUX port
  2. Plug the other connector of the 3.5mm AUX cable to your headphone or speaker.
  3. Play your media on projøctor.

Companion mode

  1.  At home page, use the remote control to select [Compenlon mode] and press [O to enter. Companion mode will be turned on and a random scene will be displayed.
  2.  To switch another scene, press the Menu] button the remote control, you will see all scenes at the bottom of the screen, I<]or[>]to sele, [OK to confirm and enter.
  3.  When your device ha8 been idle for 5 mins, twill tum to Companion mode automatically.

I08 AP Soreen mirroring
For iOS devices, Use the projector as Wi-FIAP hotspot and connect iPhone/ Pad / MacBook to projector Wi-Fl

  1.  Select iOS AP screen mirroring at the homepage
  2.  Follow the Instructions an the screen
    Note: Mirroring via Netrbk playing may not support due to copyright limitations. I08 WI-FISereen mimoring

For I0S device, connect the projector to the same WHFI with your iPhone iPad/MacBook.

  1.  Select i0S AP screen minoring at homepage
  2. Follow instructions on the screen Note: Mirroring via Notilix playing may not supported due to copyright Limitation.

Android Screen mirroring
For Android devices, Use the projector as a Wi-Fi AP hotspot and connect phones and tablets to the projector WIFI

  1.  Select Android screen minoring at the homepage.
  2.  Follow instructions on the screen.

Specifications

  1. Natve Resolution: 1920 1080
  2. Bluetooth: Bluetooth 5.1
  3. Brightness: 400 ANSI Lumene
  4. Contrast Ration: 5000:1
  5. Aspect Retro: 16:9/4:3 Adaptive
  6. Speaker: 8w2 Stereo Speaker
  7. Connection: HDMI1; USB1; AUX1;
  8. wHFI: 2.4G/5G Dual-band
  9. Projection else: 40-200
  10. Zoom:50-100%
  11. Keystone Correction: a46
  12. Warranty: 24-Month Warranty

| -1…11
---|---
40|
ID| 4.112
eo| IA1
10| I.II
eo| 7.18
80| 1.1
100|
110| 11.14
1:IO| 1UII

Warranty

30-Day Money-Back Guarantee for Any Reason You may return your undamaged product and packaging within 30 days of purchase to receive a FULL REFUND for any reason. If the reason for return Isn’t quality-related, the customer must pay for the return shipping. 24-Month Warranty for Quality-Related issues ETOE Technology’s products are warrantied to be free from material and workmanship defects for 24 months from the date of purchase. Within this period, ETOE will provide a replacement and cover any return shipping costs for products that fail in normal use. Please Note: Any provided shipping labels must be used within 20 days from the date they’re issued by ETOE Technology Customer Support.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals