ETOE A1172 Projector User Manual

June 12, 2024
ETOE

ETOE A1172 Projector

Safety Instructions

Read all instructions before you use this device. Do not make any changes that are not described in this manual. If physical injury, loss of data, or damage is caused by failure to follow instructions, the warranty does not apply.

Setup

  • To reduce the risk of fire and/or electric shock, do not expose the device to rain or moisture, and objects filled with liquids, such as vases, should not be placed on the
  • Do not place the device on soft surfaces such as tablecloths or carpets as doing so could be a fire-hazard.
  • Do not place the device in areas susceptible to excessive dust and dirt or near any appliance generating a strong magnetic field.
  • To prevent overheating, do not block or clog the ventilation openings. Never place the device in a confined Always leave enough space around the device for ventilation.
  • Protect the device against direct sunlight, heat, large temperature fluctuations and moisture.
  • When the device runs for a long period of time and the surface becomes hot, shut it down and unplug the power Resume operation only after the device has cooled.
  • Always handle the device with Avoid touching the lens.
  • Never place heavy or sharp objects on the device or the power cord. To avoid electric shock, do not disassemble.
  • Only use attachments or accessories specified by the Avoid extreme vibration. It may damage the internal components..Do not allow children to handle the device without supervision.
  • • Under the following conditions, a layer of moisture can appear inside the device which can lead to malfunctions:
    • if the device is moved from a cold to a warm area;
    • after a cold room is heated;
    • when the device is placed in a damp
  • To avoid any moisture, seal the device in a plastic bag before moving it to another room, and wait for one to two hours before you take it out of the bag.

Power Supply

  • Use only the provided power
  • Power off the device before removing the power supply from the
  • Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from this
  • Unplug this device if there are lightning storms or when unused for a long period of time.
  • Where the power plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
  • Before you make or change any connections, ensure that all devices are disconnected from the power outlet.
  • Do not touch the power cable or the power connector with wet

Hearing Safety
To avoid hearing damage, do not listen for extended periods at high volume. Set the volume at a safe level.

Cleaning

  • Power off the device and remove it from the power supply before cleaning the centre.
  • Use a sott, lint-free clo Never use liquid, gaseous, or easily flammable cleansers (like sprays, abrasives, polishes, and alcohol). Wipe over the surfaces gently. Be careful that you do not scratch the surfaces.
  • Do not use any liquid cleaning agents to clean the lens as they may damage the protective coating on the lens. Use lens cleaning paper to clean the lens of the

Repairs

  • Do not make any repairs to the device by yourself. Only have your device repaired by an authorized service center.
  • Improper maintenance can result in injuries or damage to the centre.
  • Refer all servicing to a qualified service person.

Caution: Do not stare at the operating beam. The bright light may hurt your eyes

What’s included

Overview

  1. Lens
  2. DC in
  3. HDMI 1.4 port
  4. IR receiver
  5. Power
  6. Pads
  7. Air ventilation (outlet)
  8. USB 2.0 port.
  9. Indicator
  10. 3.5mm AUX
  11. Focus adjusting knob
  12. Tripod screw hole

Attention :

  • Please do not look into the lens directly to avoid harm for your
  • Please do not block the air ventilation (outlet).

Remote Control

  1. Press the button once: power on
    Press the button twice: power off

  2. Mutes the projector’s audio

  3. Press to confirm a selection or entry

  4. Navigate menus or adjust the selected content

  5. Return to the previous menu

  6. Activate Google Assistant, Goog e s voice-powered virtual assistant service

  7. Press the button for once, go to the Android TV homepage

  8. Volume down / up

  9. Preset Netflix button

  10. Preset Prime Video button

  11. Press to launch the shortcut menu

  12. Press the button once, go to the projector Homepage

Get Started  Placement

  1. Place the projector right towards the projection surface to get a rectangle picture.
  2. The distance between the projector and the projection surface determines the picture size.
  3. Check the projection distance and screen size on the specifications part.

Prepare the Remote Control
Install the remote control batteries (batteries not included).

  1. Press and open the battery cover, as illustrated.
  2. Install two AAA batteries. Make sure that the positive and negative ends are positioned correctly, as illustrated.
  3. Place the battery cover back until it clicks into place.

Power On

  • Press the power button once to power on
  • Press the power button twice to power Off

Focus

  • Place the projector towards a suitable projection surface or wall, adjust the distance for a proper size of picture.
  • Scroll the [Focus Adjusting Knob] left or right until the picture is crystal clear.

Note : The projection distance must between 1.1m to 5.4m

Select Your Language
When starting the projector for the first time, you will be guided to a page to select language, use the remote control or select your language. Then press the right button and select “Complete” to enter the next page.

Pair Remote Control in Bluetooth Mode
After selecting a language, you will be at a Bluetooth remote pairing page, follow the instructions on the page.

  1. Please hold the remote near the projector.
  2. Press the [Volume-] and [OK] keys together for about 10 seconds.
  3. When the screen shows “Connected”, your remote LED indicator turn to blue, and the remote control is paired

Set up Android TV
Follow the setup wizard on Android TV, select your language, set up a Wi-Fi connection, sign in to a Google account, and carry out other related procedures. When you complete the Android TV setup wizard, the Android TV home screen will appear. Now you can start watching your favorite shows by downloading streaming apps

Settings

Go through the set-up process when you turn on the projector for the first time.

Android TV Setting

Bluetooth pairing
If you want to connect to Bluetooth speakers/headphones on the Android TV interface, select Settings->Remotes&Accessories->Add accessory, then select the device to be connected. Bluetooth connection only works while on the Android TV system

Android TV Remote App
The Android TV system could be controlled by downloading the remote app on a smartphone. Make sure your device is connected to the same Wi-Fi network as the projector, Bluetooth is turned on, and your Android/iOS device is updated to the newest version.

Android devices:
Download the “Android TV Remote” app from Google Play, open the app, choose “HAKO mini” frorn the Remote tab, click “connect”, enter the verification code displayed on the projector screen.

iOS devices :
Download the “Android TV” app frorn the App Store, open the app, allow it to use the local network to set up and control your connected devices, choose “HAKO mini” from the Remote tab, click “connect”, enter the verification code displayed on the projector screen.

Adding Accounts
For new Google users, sign up for a new Google account using the TV for easier login and payment security. Add an account or switch accounts under Accounts in the Settings Menu.

Dolby Audio not supported
the projector does not support Dolby Audio. If you are watching videos with Dolby Audio, please turn off all Dolby Digital-related output on your video resource.

Projection settings

Press the button on the remote control, go to projector homepage, and select Settings. Projection mode

Zoom in/out

Use the remote control to resize the picture size from 50% to 100% without moving the projector.

Keystone correction

  • Digital Keystone Correction:
    The keystone effect refers to when the projected image is noticeably wider at one side. It occurs when the projector is not perpendicular to the screen To correct the keystone effect, press the button  to go to projector homepage, and select Settings–>Projection Settings –>Vertical Correction/Horizontal Correction to adjust.

  • Four-Point Correction:
    If the projected image is stretched or distorted along both axes due to the angle of the projection, select Settings—>Four Point Correction, choose the corner you want to adjust, and follow the on-screen instructions to correct the image.

Keystone correction reset
To restore the default settings, select Keystone Correction Reset and press “OK”

**Other settings

**

Screen Saver
The screen saver automatically starts whenever your projector sits idle for the default time. You could change the default time or turn it off.

Screensaver Video
Select default screen saver video.

Screensaver Timeout Shutdown
Set the shutdown timer for the projector.

Language Settings
Select an on-screen display language.

Restore Factory Settings
Reset your device and restore the factory setting

Chromecast (wireless connection)

The Chromecast feature only works while you are in the Android TV system. Cast from Chromecast-enabled sites/apps (for Android/iOS devices)

  1. Make sure your device and the Android TV (HAKO mini) are connected to the same Wi-Fi network, and that you are running the latest version of the Chromecast-enabled app.
  2. Launch the Chromecast-enabled site/app.
  3. Tap the cast button   and choose the “HAKO mini”

Cast from the Chrome browser tab (for computers)

  1. CD Connect your computer and projector to the same Wi-Fi network.
  2. Click “Cast’ at the top right : of the Chrome browser tab, and then choose from the sources whether you want to cast the tab or the screen
  3. Choose the “HAKO mini” to cast.

Mirror from Android devices

  1. CD Make sure your Android device is on the same Wi-Fi network as your Android TV (HAKO mini)
  2. Download the “Google Home· app on your Android device.
  3. Open the “Google Home” app, choose “HAKO Mini·
  4. Tap ·cast my screen·.

Mirror from iOS devices

  1. Make sure your iOS device is connected to the same Wi-Fi network as your Android TV (HAKO mini)
  2. Download the “AirScreen· app for Android TV system. from the Google Play Store of
  3. Open the “AirScreen” app and follow the on-screen instructions on AirScreen

Wired Connections

Connect to an HDMI playback device
This projector supports connections with various HDMI playback devices such as PC, TV stick, TV box, DVD player, set-top box (STB), game consoles or other devices.

  1. Connect this projector to an HDMI playback device with an HDMI cable (not provided).
  2. Press the button on the remote control to go to projector homepage, select [HDMI). and press [OK].

Connect to a flash drive
With this projector, you can enjoy music, video, and pictures, that are stored on a USB storage device.

  1. Plug in the USB storage device.
  2. Press the button on the remote control to go to projector homepage, select [USB). and press [OK].
  3. Select the file you plan to play from the lile and older menu.
  4. Press [OK) to start playing.

Connect to a headphone via an AUX cable
You can connect a headphone or speaker to ETOE Projector via AUX cable as well.

  • CD Plug in the 3.5mm AUX cable connector to the ETOE projector AUX port.
  • Plug the other connector of the 3.5mm AUX cable to your headphone or speaker. @Play your media on the projector.

Shortcut Menu

Long-press the – button to pop up the shortcut menu

  • Press the  navigation button to select the option
  • Press the button to go to the next page
  • Press   button to adjust parameter
  • Press the “OK” button to save

Image Mode

| Standard| Keeps natural looking colors witha balance of warm and cool tones
---|---|---
Light| Provides more picture details andcolor sharpness
Soft| Provides warm colors withlower light
Personal| Manually set the Brightness,contrast, Saturation, Sharpnessand Hue

Color Temp

| Cold| Provides cold color temp
Normal| Provides normal temp
Warm| Provides warm temp
Personal| Manually set the Red, Green and Blue

Sound Mode

| Standard| Provides standard tones
Music| Provides more detailed tone
Movie| Provides home theater-style sound
Personal| Manually set the sound of each frequency band

Projection Setting

| Zoom In/Out| Zoom in or out of theprojection image
Vertical Correction|

Perform keystone correction

HorizontalCorrection
Four Point Correction
KeystoneCorrection Reset| Reset keystone correction

Specifications

  • CPU: ARM Quad 64-bit Cortex-A53
  • Android OS: Android'” 10.0 Bluetooth: Bluetooth 5.1
  • Wi-Fi: 2.4G/5 GHz 802.11a/b/g/n/ac Native Resolution: 1920’1080
  • Throw Rat o: 1.22 Contrast Rat o: 3000:1
  • Aspect Ratio: 16:9/4:3 Adaptive Speaker: 3W’2 Stereo Speaker
  • Connection Port: HDMl’1; USB’1; AUX’1 Projection Size: 40″-150″
  • Zoom: 50%-100%
  • Keystone Correction: ±45°
  • Recommended Ambient: 41°F to 95°F/5°C to 35°C
  • Relative Humidity: 15%-85% (non-condensing)
  • Warranty: 12-Month

Warranty

30-Day Money-Back Guarantee for Any Reason
You may return your undamaged product within 30 days of the date of purchase to receive a full refund for any reason. For non-quality related warranty claims, the buyer is responsible for shipping costs.

12-Month Warranty for Quality-Related Issues
Every ETOE product comes with one year of quality-related issues coverage. If you submit a claim to our support mail, ETOE will, at its option:

  1. Replace the ETOE Product with a replacement product of the same model and cover any return shipping costs.
  2. Exchange the ETOE Product for a refund of your purchase

Projection Distance and Screen Size

Screen size

(inch)

| Width (inch)| Width (cm)| Heght (inch)| Height (cm)| Distance

(cm)

| Distance

(fl)

---|---|---|---|---|---|---
40| 34.9| 88.6| 19.6| 49.8| 108.0| 3.5
60| 52.3| 132.8| 29.4| 74.7| 162.1| 5.3
80| 69.7| 177.1| 39.2| 99.6| 216.1| 7.1
100| 87.2| 221.4| 49.0| 124.5| 270.1| 8.9

FCC Notice
This device complies with the FCC rules, Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the partly responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • • Increase the separation between equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/ TV technician for

RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body

Model : A1172

© ETOE Technology Limited
All rights reserved. ETOE and the ETOE logo are trademarks of ETOE Technology Limited, which is registered in the United States and other countries. All other trademarks are the property of the irrespective owners.

Manufacturer: HUNAN ETOE Technology Co., Ltd

Address: Room 603, Building 3, Zone A, Jindaoyuan, N0.169, Huizhi Zhong Road, High-tech District, Changsha

E-mail: support@etoeofficial.com

Made in China

Please contact us via:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals