InnoGear Microphone Arm, Upgraded Mic Arm Microphone Stand Boom Suspension-Complete Features/Owner’s Guide

InnoGear Microphone Arm, Upgraded Mic Arm Microphone Stand Boom

Suspension

Specifications

• DIMENSIONS : 15 x 1.5 x 4 inches,
• WEIGHT : 1.35 pounds,
• COLOR: Black,
• MANUFACTURER: InnoGear

The InnoGear Microphone arm with suspension stand is one of the low budgets yet good quality microphone arms and stands. The arm of this product is foldable which makes it super easy to be carried around. It has a knob that can be used to adjust the angle of the microphone. It has a desk mount made of zinc alloy which has the anti-scratch pad and a mouth of about 2 inches which can fit to most the desktops. The microphone clip has a diameter of 1.10” which makes it suitable for stage, studios and broadcasting. It has a 5/8” – 27 make to 3/8” – 16 female screw adapters. It has a strong spring with an extra positioning screw. It has the capability to handle a maximum load of 53oz/1.5kg. It is compatible with Blue Yet, Blue Snowball, Blue Yeti nano and other Mics.

How to install the InnoGear Microphone Stand?

1. Unscrew the clamp to enlarge the opening.
2. Once the clamp is wide enough to fit your table, tighten the screw to ensure a nice fit.
3. Make sure the clamp is fixed tightly to the table.
4. Take the other end of the arm and put it in to clamp and adjust it.
5. On the opposite end of the stand, there is a 5-8” connector. Put the adapter of your microphone or the microphone directly into it.
6. You can use the clamp around the rode to adjust it according to your wish.

• Maximum Vertical Reach of the Stand
  The maximum vertical reach of the stand is 27 inches.

• Maximum Horizontal Reach of the Stand
  The maximum horizontal reach of the stand is 37 inches.

• Maximum Weight
  It has the capability to handle a maximum load of 53oz/1.5kg.

VERDICT
This is a good quality and cheap microphone arm. You don’t have to be a professional YouTuber or steamer to get this. It performs the basic functions of holding the microphone is place and providing a good adjustability range very well.

FREQUENTLY ASKED QUESTIONS

• Can this hold a blue snowball mic?
  Yes. Attach the Blue Snowball microphone with the 5/8″-27 male to 3/8″-16 female threaded screw adapter that comes with the stand.

• Will it work for the Rode NT USB1 mic?
  Yes, it will work as the arm gas standard small threads.

• Can I put a Blue Yeti upside down on this mount without falling?
  Yes, you can. The arm comes with a plastic spacer which is to be screwed in to the bottom of the Yeti. Screw the Yeti on the mount and it will fit it perfectly

• Does this work for NW 700?
  Yes, it works with NW 700.

• Will a WebCam fit on this arm?
  Yes, just clamp the webcam on the top of the arm.

• Can it hold a Blue Yeti at 90°?
  Yes, once properly clamped, the arm can hold the Blue Yeti at 90 degrees.

• How long is the arm when fully extended?
  The arm can be fully extended vertically to a length of 27” and horizontally to a length of 37”.

• Will this fit on an Ikea Malm desk, they are quite thick?
  Yes, the clamp of the stand is adjustable and can be widened to a good extend

• Can you use this stand for a Blue Yeti microphone?
  Yes, you can use it for a Blue Yeti microphone

• How does this mount to the desk?
  It works like a C clamp. You open the opening by twisting the screw. Then the side of your table/desk is placed inside the opening. Twist the screw to tighten it.

• Does this work for any mic?
  It works with all mics that have a 3/8 and a 5/8 adapter.

• Does this work with the Rode podcaster?
  Yes, the Rode podcaster has a 5/8 thread. The InnoGear Arms comes with both 5/8- and 3/8-inch threading.

• Will this work for Audio Technica AT2020?
  Yes, it works completely fine with Audio Technica AT2020.

• Is this compatible with the AT2020 Cardioid Condenser mic?
  Yes, it has a standard screw making it compatible with most of the mic.

• Is it compatible with the Toner t30 microphone?
  Yes, it is compatible with Toner T30.

• Will my condenser mic work?
  Yes, as long as your mic has a regular thread pattern.

• Can I purchase only a 5/8″ female to 3/8″ male adapter, that’s all I need, to fit my Technica 2020 mic to my mic stand?
  Yes, you can purchase the 5/8″ female to 3/8″ male adapter

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>