hugolog DE-DOOR-16H-1162 Keyless Entry Door Lock Installation Guide
- June 5, 2024
- hugolog
Table of Contents
Thank you for choosing Hugolog.
Please read this user manual before fitting and using your keypad lock,
and keep it for future reference.
“need help?
For technical support and more, please email:
support@hugo-log.com”
Installation Guide
1 Prepare the door and check the dimensions
A Measure to confirm that the hole in the door is 2-1/8″ (54 mm) .| B Measure
to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70 mm).| C
Measure to confirm that the hole in the door edge is 1″ (25 mm).| D Measure to
confirm that the door is 1-3/8″ to 2″ (35 mm or 50 mm)thick.
---|---|---|---
Install the latch and strike
A Hold the latch in front of the door hole, with the latch face flush against the door edge.
B Is the door edge chiseled?
C Use a screwdriver to test if the deadbolt works smoothly.
D Install strikes on the door frame.
**IMPORTANT:** Make a sure the hole in the door frame is drilled a
minimum of 1″ (25 mm) deep.
Install exterior assembly
An IMPORTANT: Before installation, make sure the latch is fully retracted
(in the unlocked position) .| BRoute the cable below the latch.
---|---
C Send the cable through the bottom horizontal slot in the mounting plate.| D
Secure the mounting plate with the supplied screws.
---|---
Install interior assembly
IMPORTANT: Do not load batteries until lock is completely installed.
Remove the battery cover.| Connect the cable and ensure tight cable
connection.| B Rotate the turn piece in a vertical position and make sure the
latch is still fully retracted (in the unlocked position). Insert the torque
blade through the center hole in the mounting plate.
---|---|---
C Test the turn piece for smooth rotation.
If turn piece doesn’t rotate, repeat step 4C, making sure the turn piece in
vertical position.| D Secure the interior assembly with the supplied screws.
---|---
Detect left/right-hand door installation
Reset the lock to teach the lock the orientation of the door.
IMPORTANT: This step is required and crucial for the lock to operate
properly.
While the door is OPEN and unlocked, load 3 AA batteries
into the interior assembly.
IMPORTANT: For best results, use new, non-rechargeable
Alkaline batteries only.| B Press and hold the Reset button on the interior
assembly using a pen or a paper clip.| C Load the last battery and keep
holding the reset button for 3 seconds until you hear the sound of “beep”. The
latch bolt will extend to learn the orientation of the door.
---|---|---
How To Use
UNLOCK the door from outside![hugolog DE DOOR 16H 1162 Keyless Entry Door Lock
- outside1](https://manuals.plus/wp-content/uploads/2022/04/hugolog-DE-DOOR- 16H-1162-Keyless-Entry-Door-Lock-outside1-550x245.png)
UNLOCK the door from inside
LOCK the door from outside
Manual Mode
Press any key on keypad for 2 seconds.
Auto Re-lock Mode
In Auto re-lock mode, the bolt will extend out automatically in 30 seconds
after unlocking.
LOCK the door from inside
Manual Mode
Rotate the thumb turn to Lock position.
Auto Re-lock Mode
In Auto re-lock mode, the device will be locked automatically.
Programming Instructions
Information & Safety Warnings
Protect your User Codes and Master Code.
Restrict access to your lock’s interior assembly and routinely check your
settings to ensure they have not been altered without your knowledge.
This lockset is designed to provide the highest standard of product quality
and performance. Care should be taken to ensure a long-lasting finish. When
cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic
soaps, abrasive cleaners or polishes could damage the coating and result in
tarnishing.
IMPORTANT: Do not load batteries until lock is completely installed.
- Master Code( 4 to 10 digits) : The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
- User Code(4 to 10 digits) : A total of 20 User Codes (and one temporary one-time User Code) may be programmed.
- Both master and user pin codes don not support the following combination of numbers.
Parts Illustrations
Item | Specifications | Remarks |
---|
Battery
(Use new, non-rechargeable
Alkaline batteries only.)| AA alkaline battery x4
(Operation voltage: 4.6~6.0V)| Last up to one year
(10 times open/close per day)
The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
Definitions
Master Code
Required for programming and feature settings. Master code can be used to
unlock the door under vacation mode. The default master code needs to be
changed before programming.
The property owner/ manager should keep this information confidential.
Auto-Lock
Automatically locks the deadbolt 30 seconds after unlocking. This feature is
off by default. You can set the Auto-Lock time delay between 10 and 99
seconds.
Emergency Power Port
Emergency USB Port can be used when the battery is completely dead. Supply
power by connecting an external power bank to the micro-USB port and hold
the reboot button for 3 seconds.
Wrong Entry Limit
After 10 unsuccessful attempts at entering a valid PIN code, the unit will
shut down for 3 minutes.
Silent Mode
The beep sounds when pressing the keypad can be muted.
But you will still hear low battery and system alerts.
Vacation Mode
This is a security feature for you when you are leaving your home for a
vacation or long trip. Enabling vacation mode will restrict all user codes
until the master code is
entered on the keypad. If the lock is unlocked by thumb turn, the lock will
sound an alarm.
One Time User Code
This code can only be used once and is automatically deleted when used.
Unlock with a Fake code
Users can prevent pin code exposure from strangers by entering random digits
before or after pin code.
Quick Set Up
IMPORTANT: The default Master Code is 12345678. It is required that you change it to a code of your own before programming.
Notes:
When setting is unsuccessful, the indicator light will flash red.
Factory Default Settings
Settings | Factory Defaut |
---|---|
Master Code | 12345678 |
Auto-Lock | Disabled |
Silent Mode | Disabled |
Wrong Code Entry Limit | 10 times |
Shutdown Time | 3 mins |
Vacation Mode | Disabled |
Restore To Factory Default Settings
This procedure will delete all User Codes associated with the lock.
- Keep the door open and unlock it.
- Press and hold the Reset button, at the same time take out one battery and then place it back.
- Keep holding the Reset button for 3 seconds, until you hear the sound of beep.
Troubleshooting
The turn piece cannot rotate or operate the lock.
Remove and re-install the lock, making sure that the turn piece is in a
vertical position.
The lock cannot be locked or unlocked by the keypad.
Make sure that the codes are not disabled. If needed, restore the lock’s
default settings.
The keypad doesn’t respond when touched ( no lights are visible and no
beeping is heard) .
Make sure the cables are properly connected and make sure the batteries are
new and installed correctly.
After the installation of the batteries, there is no response when you
press any button and no beeps are heard.
Check the cable connection and the polarity of the batteries. Also, make sure
the batteries are not dead.
I forgot my Master Codes.
Perform a reset in order to erase all passcodes. Once the reset is complete,
all passcodes will be erased and the Master code will return to the default
value ( 12345678) .
- If none of the above resolves your issue, check out our updated user manual by scanning the code below. You could also contact Hugolog customer service at
support@hugo-log.com.
Scan to access installation video and updated manual.
NEED HELP?
www.hugo-log.com
support@hugo-log.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>