hugolog HU01 Smart Lock Instruction Manual
- June 5, 2024
- hugolog
Table of Contents
hugolog- HU01 -Smart -Lock -LOGO
Warnings
- Failure to follow these instructions could result in damage to the product and avoid the factory waranty.
- The accuracy of the door preparation is critical for the proper functioning and security of this product. Misalignment can cause performance degradation and lessening of security.
- Finish Care: This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
CAUTION
IMPORTANT: Do not install batteries until the lock is completely installed on door.
- Master PIN Code (4~1 O digit): Default master pin code is “7 2345678”, please modify it after installation. If you forget your master pin code, you can reset your lock back to factory settings.
- User PIN Code (4~1 O digit): User pin codes can be set up through master pin code. Up to 20 user pin code can be stored.
- Both master and user pin codes don’t support the following combination of numbers.
**Parts Illustrations
**
CAUTION
Master and User pin code have 4-10 digits, the default master pin code is
12345678 J. Please changeit prior to programming ot the lock.
Definitions
Master Mode
The master mode could be entered by entering[ **+Master PIN Code+#] to progam
the lock.
Master PIN Code:
The master pin code is used for programming and for feature settings.
Auto Re-lock:
After successful pin code entry and the unit unlocks, it will automatically
re-lock after 30 seconds. This feature is disabled in default setting.
Manual Mode:
Auto re-lock function could be adjusted to manual mode. In manual mode the
lock could be locked only by pressing any key for 2 seconds from outside or
using thumb turn from inside.
Shutdown Time:
The lock will shutdown for a default of 3 mins and not allow operation after
the wrong code entry limit (10 times) has been met When the unit is in
shutdown, the light will fiash when you are trying to use keypad.
Silent Mode:
The beeper will not make any voice.
Status indicators:
Located on exterior assembly.
User PIN code:
The user pin code operates the lock. Maximum number of user pin codes is 20.
Reset button:
After reset operation, the lock will be restored to factory default settings,
all user credentials will be deleted. Refer to reset guide.
Factory Default settings
Lock Operation
Notes:
- Beeps sound only when beeper is enabled.
- If the indicators show 3 red lights+ 3 beeps, your setting failed. The system will exit master mode. Please try to enter master mode again if you continue your processing.
How to use
Unlock the door
-
Unlock the door from outside Master /User pin code or key
-
Unlock the door from inside Manual thumb turn Turn the thumb turn on inside body Lock the door .
-
Lock the door from outside Auto Re-lock Mode In Auto re-lock mode, the bolt will extend out automatically in 30 seconds after unlocking.Press any key on keypad for 2 seconds.
Manual Mode -
Lock the door from inside Auto Re-lock Mode In Auto re-lock mode, the device will be locked automatically. The device could be locked by turning the thumb turn on inside body.
Manual Mode
Unlock with Fake PIN code
User can prevent pin code exposure from strangers by entering random digits before or after pin code.
Reset to factory default settings
Operations on lock
- Open the door and keep the lock in “unlock” status.
- Open battery box and find the reset button.
- User a sharp thing to press and hold the reset button.
- Keep holding the reset button and remove a battetry from battery box then replace it.
- Keep holding the reset button for another 3 seconds untill hearing voice guide.
Download APP
Bluetooth network configuration must be restored to factory settings first,
and network configuration completed within 5 minutes after factory reset
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>