hugolog HU03 Smart Lock Installation Guide

hugolog HU03 Smart Lock Installation

Installation Guide

Tool Needed

Door prep

1. 2-1/8 (54mm) hole saw
2. 1″ (26mm) boring bit
3. 7 /64″ (2.5mm) drill bit
4. 3/8″ (10mm) drill bit
5. Chisel&Hammer

Lock Installation #2 Philips screwdriver

Important Notice:
Make sure your door is prepared prior to installation. Only drill an upper hole if you wish the lock to have added stability. Please refer to the provided template for drilling if needed.

Exterior assembly

hugolog reserves all rights for the fmal Interpretation to this Instruction All design and specifications are subject to change without notice

Interior assembly

Preparing for Installation

1. Measure the dimension of the hole shown.If the measurement is 1-1 /2″(38mm), remove the fire cup.

2. Change faceplate,if necessary.

3. Adjust the deadbolt.
   NOTE: Boa ships with bsckset in 2-3/8″(60mm) poEition. If required, turn the txllt case sOO pull to exteo:J to 2-3/4″ (70 mm)backset pa,ition. {see pictL.re OOow)
   The bolt must be in retracted(unlocked) position when you are changing backset.

4. Adjust the tailpiece according to your door’s thickness.
   Carefully break off cylinder tellplece 8t required mark for your door thickness.
   & Caution:Uoo two pliers as sho’Ml ir tailpiece will te damaged

Installation

1. Install strike on the door frame. &. NOTE: Make SLnJ to allow for the Wt to te centered in tre strl<e

2. Use a screwdriver to test if the deadbolt works smoothly.

3. Make sure the bolt in a retracted(unlocked) position.
   NOTE: The bolt must be in retracted (l..rjoc:koo) position befCYs L.l:l, 11″\ITTallo;ithslockoot

4. Hold the exterior assembly flush to the door, and pull the key tailpiece and cable through the door hole.

   • This home is for the optional cross txllt provided for stabilizing,,.r lock lf so-called a hole, secL.re-tighten the postbeforemo.mail”IQ m,=oocr
   • NOTE: Cable trust go through doorrdeUlda”Theo out

5. Positon the inside mounting plate by first routing the cable and connector through the mounting plate’s cable hole.

6. Secure both assemblies using 8/32×34(optional) and 1 / 4×65 screws. Make sure that exterior assembly is vertically aligned. Tighten securely with a #2 Philips screwdriver.

7. Place rotation shaft in the hole on the inside asasembly.

8. Attach cable assembly to the interior assembly  PCB by lining up notches on top of cable connector to slots on PCB connector. Press connector in firmly using thumbs untill commpletely connected.

9. Install interior assembly on inside mounting plate.

10. Secure using screw through the interior assembly onto the mounting plate.
    NOTE: The ror1z01tal orientation or the ta I piece as you Insert the inside escutcheon (tr!.lli:J ti..msh<xJld be vatical)
    NOTE: Testing operatle<1 using boc:l<t.,p key ard th…rro tun beiore installingbatterias.soo ifboltworks srrooth

11. Reset the lock to learn the orientation of your door.
    NOTE: Resetting tha lock before use is required and crucial fcr the lock to operate prcµir.

12. Install battery cover.

13. Install reinforcement plate and strike intodoor jamb.

Download APP

Bluetooth network configuration must be restored to factory settings first, and network configuration completed within 5 minutes after factory reset.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>