SOURCE 8088029 LED Strip Light Instruction Manual
- June 5, 2024
- Source
Table of Contents
- SOURCE 8088029 LED Strip Light
- Instruction Manual
- COMPONENT IDENTIFICATION REMOTE CONTROL
- GETTING STARTED REMOTE CONTROL
- INSTALLATION
- REMOTE CONTROL MUST BE CONNECT TO THE SIGNAL RECEIVER
- OPERATING INSTRUCTIONS
- TO CREATE DIY COLOURS
- APPLICATION
- SPECIFICATIONS
- SAFETY WARNINGS
- THE SOURCE – WARRANTY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
SOURCE 8088029 LED Strip Light
Instruction Manual
INCLUDED
- 10m (32ft.) LED strip light
- 12V adapter with an output connector
- Remote control with 1 CR2025 battery
- Instruction manual
COMPONENT IDENTIFICATION REMOTE CONTROL
GETTING STARTED REMOTE CONTROL
The remote control has a battery installed. Please remove the tab for the battery to begin operation.
- Locate the battery compartment on the side of the remote control.
- Remove the dead battery and insert one 3V CR2025 battery (spare not included). Please ensure the battery is installed following the correct polarities (+/-).
- Place the battery cover back and press until it locks.
INSTALLATION
- Clean the surface you’d like to stick the light to.
- Peel off the backing of the adhesive tape.
- Press and hold the light strip firmly against the surface.
- Connect the light strip in the correct order (see photo below, ensure arrows are aligned).
- Connect the plug to the wall outlet the using the included 12V/3A adapter.
JOIN THE LED LIGHT STRIP TO THE USB RECEIVER/CONTROLLER
Attach the USB receiver/controller to the LED light strip as shown below. Connect the light strip in the correct order.
REMOTE CONTROL MUST BE CONNECT TO THE SIGNAL RECEIVER
NOTE: For optimal performance, place the receiver on the LED light strip away from your TVs receiver to avoid interference from your TV remote. Make sure the receiver is in line of sight on order for the remote to work.
OPERATING INSTRUCTIONS
- Turn the LED strip light ON by pressing the ON button on the remote control.
- Select a colour and effect, and push the corresponding button.
- Set the colour brightness by pressing the brightness buttons.
- Push OFF to turn the LED strip light OFF.
NOTE: The colour settings are mixed, and the colour tints may exhibit minor deviations.
TO CREATE DIY COLOURS
- Press DIY 1 button and light will show white. Press the down arrows above the DIY buttons, press red down button until all red is off, press green down button until all green is off, and press blue down button until all blue is gone.
- When all colours are down the light strip will look off. Now you can add red, green and blue back in to create your own custom colour.
- Press DIY 1 again to set the colour
- Repeat process with the 5 other DIY buttons.
APPLICATION
- Use to decorate any room in your house, porch, desk, hotel, club, bars, vehicle, boat, TV, studio.
- Decorate for Christmas, Halloween, weddings, birthday parties and more.
SPECIFICATIONS
- Length: 10m/rol
- Power Rating: 36W
- Light Output: 12V
- Remote Output: 3V (1 CR2025 3V battery)
- Rated Current: 3A
- Operating Temperature: -20~45°
- Storage Temperature: 0~60°
- Environment Humidity: 40-70% RH
- LED Lifetime: 50-100 K hours
- Waterproof: IP65
SAFETY WARNINGS
- DO NOT use if product is damaged.
- The controller box is NOT waterproof; only the LED stip light is.
- Connect according to these instructions to avoid a malfunction.
- DO NOT use the lights when on the spool.
THE SOURCE – WARRANTY
The Source warrants that this product will be free from defects in materials and workmanship for a period of 6 months from the date of purchase. Within this period, simply take the product and your proof of purchase to any The Source store or participating dealer and the product will be replaced (where available) without charge. Any product which has been subject to misuse or accidental damage is excluded from this warranty. This warranty is only applicable to a product purchased through The Source company-owned stores or participating dealers in Canada where the warranty is included with the product. While this warranty does not confer any legal rights other than those set out above, you may have additional statutory rights which will vary under the laws of the various countries, states, provinces and other governmental entities in which The Source operates. This warranty is subject to all statutory rights you may have in Canada.
Imported by: The Source, Barrie, Ontario, Canada, L4M 4W5 Manufactured in
China
www.thesource.ca © 2022 The Source. All rights
reserved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>