Aisidra AD BA010 Wireless Adapter User Guide

AD BA010 Wireless Adapter
User Guide

Package Contents

Product Diagram

Specification

RX: aptXTM low latency, aptXTM, SBC,AAC
Range| 33ft/10 m
Battery Capacity| 160 mAh
Charging Power| 5V DC
Working Hours| 8-10hours
Charging Time| 2hours
Operating temperature| -10 to 55 C
Dimension (L x W x H)| 1.88 x 1.39 x 0.43 in /
4.80 x 3.55 x 1.10 cm
Weight| 0.53 oz / 15 g

Use as Transmitter

Button for 3 seconds
Power Off| When on, press and hold the Power
Button for 3 seconds
Pairing| When powered on, press the Power
Button twice to start pairing
Mode Switch| Slide the Mode Switch to and from
TX and RX
Reconnect To All
Connected Devices| Short Press the Power button to reconnect to all connected devices; if no one connected after 12 seconds will auto in paring mode
---|---
Clear Pair List| When off, press and hold power button 7 seconds will clear all connected device information
Reset| When on, press the power button and plug it into a power source at the same time.
Auto Power Off| The device will auto power-off if battery lower than 3.1V
Low Battery Alarm| The device will have a low battery alarm every 3 minutes if the battery is lower than 3.3V
LED Indicators| Status
---|---
Solid Red LED| Charging
LED Off| Fully charged
Flashing Red and Blue| Pairing
Flashing Red| Low battery
Solid Blue LED| Successfully paired
Flashing Blue| Powered on but not paired with
Bluetooth® devices

Use as Receiver

to all connected devices; if not connected after 12 seconds will auto in paring mode
Auto Power Off| The device will auto power off if the battery is lower than 3.1V
Low Battery Alarm| The device will have a low battery alarm every 3 minutes if the battery is lower than 3.3V
LED Indicators| Status
---|---
Solid Red LED| Charging
LED Off| Fully charged
Flashing Red and Blue| Pairing
Flashing Red| Low battery
Solid Blue LED| Successfully paired
Flashing Blue| Powered on but not paired with Bluetooth devices
---|---
Flashing Blue twice| Unpaired and Standby

How to Use

Charging

1. Connect the micro-USB end of the cable to the charging port of the Bluetooth adapter.
2. Plug the USB end of the charging cable to a USB charging port or any active USB port.
3. The LED indicator will turn red when charging and will automatically turn off when fully charged.

Note:

• You can use the adapter while it is charging.
• We recommend charging the unit for at least 2 hours before using it for the first time.

How to Pair

Pair in TX mode:

1. Set Aisidra AD-BA010 to TX mode and connect it to the AUDIO OUTPUT jack of your non-Bluetooth devices such as TWPC/MP3 player.
2. Place your Bluetooth audio receiving device such as a Bluetooth headphones speaker within 3 feet / 1 meter and set it to pairing mode.
3. Press and hold the Power Button for 5 seconds and tap twice to enter pairing mode (blinking red and blue). Within a few seconds, both devices will pair to each other and the transmitter will stay solid blue.

How to pair with Airpods in TX mode?

1. .Make sure the adapter is set into TX mode, both devices are within 3ft to each other;
2. Find the circular button on the rear side of the charging case of your Airpods;
3. Open the lid of your Airpods charging case (do not remove Airpods from the case)
4. Tap and hold the circular button until the light inside the case blinks white
5. Tum on the adapter and it will automatically enter pairing mode (blinking red and blue);
6. Both devices will search for each other and connect to each other within seconds. The transmitter will stay solid blue while the Airpods charging case will turn into green light once connected.

Pair in RX Mode:
Press and hold the Power Button of the adapter for 3 seconds, it will start pairing.
1. Activate the Bluetooth function on your phone and search for the nearby Bluetooth devices:

• For iOS: Settings > Bluetooth > On
• For Android: Settings > Wireless & Networks >Bluetooth: On > Scan for devices

2. Find “AD-I3A010” in the search results and tap on it to connect. Once connected, the LED indicator will turn solid blue.
Note:

• The adapter enters pairing mode automatically when powered on for the first time.
• The original paring memory in TX mode will be cleared after a mode switch, but in RX mode will not. It will automatically start pairing each time when powered on.
• If a PIN code is required for pairing, try 0000,8888.1111 or 1234.
• The adapter can remember two recently paired devices and will attempt to pair with devices automatically, without going into pairing mode.
• Please do not turn on the adapter right after it is tumed off, otherwise, the adapter might crash and the battery will be damaged.
• If the adapter fails to pair with your devices, please kindly clear the pairing history of both devices and try to repair them following the pairing steps.
• Bluetooth headphones speakers are also required to support AptX Low Latency Codec to run low latency mode, otherwise, the receiving device might use another codec (e.g.SBC, aptX) which might result in a 70-200ms audio delay that might be noticeable to some users.

Pair with two devices at the same time In TX mode :
The adapter is able to pair with two Bluetooth‘) stereo earphones/speakers at the same time.

1. Follow the previous instructions in the “Pairing” section to pair the AD-BA010 with your first device.
2. Turn off the Bluetooth® function on your first device, tap the Power Button twice to pair and connect to your second device.
3. Turn on the Bluetooth® function on your first device. In approximately 12 seconds, the first device will automatically connect in.

Note:

• When you pair with two devices, both can play music at the same time.
• The adapter will automatically re-pair when powered on.

In RX mode:
The adapter is able to pair with two Bluetooth® devices at the same time.

1. Follow previous instructions in the “Pairing” section to pair the AD-BA010 with your first device. Disable the Bluetooth® function on your first device. Tap the Power Button twice to pair it with the second device.
2. Turn on the Bluetooth® of the first device, now AD-BA010 adapter is successfully paired with both two devices.

Note:

• Only one device can play music at any time. You have to stop the music on one device to play on the other.
• The adapter will automatically re-pair when powered on.

Care and Maintenance

• Keep the adapter away from heat and humidity.
• Do not expose the adapter to direct sunlight or extreme heat
• Do not try to take the adapter apart. It may cause serious damage.
• Do not drop or knock the adapter on hard surfaces as it damages the interior circuit.
• Do not use chemicals or detergents to clean the product.
• Do not scrape the surface with sharp objects.

Warranty and Service
This product is covered with an Aisidra product and labor warranty for 12 months from the date of its original purchase.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>