Aisidra AD-BA200 Wireless 2 In 1 Adapter User Manual
- June 13, 2024
- Aisidra
Table of Contents
U ser M anu al
WIRELESS 2-IN-1 ADAPTER
AD-BA200
Quick Guide
Power On/Off
Slide the switch to TX or RX or OFF.
- Auto shutdown if no connection in 10mins.
Enter Pairing Status / Disconnect
Hold OK to enter pairing status.
- To repair when connecting to the last connected devices.
- To pair the second device.
- To disconnect all the connected devices.
What’’s included
Specification
| Bluetooth Profile | A2DP / HFP /AVRCP |
|---|---|
| Bluetooth Specification | Bluetooth 5.3 |
| Audio Codec | DC: aptX1″ / SBC RX: aptXN / SBC /AAC |
| Working Range | 15M |
| Battery Capacity | 26OrnAh |
| Charging Power | 6V DC |
| Working Hours | 12H |
| Charging Time | 1.5H |
| Weight | 28.3g |
Product Diagram
- 3.5mm Audio Jack
- Volume Up/Previous Track
- Volume Down/Next Track
- Slide Switch
- Up Button
- Back Button
- Down Button
- LCD Screen
- Confirm/Pairing Button
- Play/Pause Button
- Type-C Charging Port
- Leash String
- Twist Cap
Transmitter (TX) Mode
STEP 1: Connect Your Device
Unscrew the twist cap, plug the 3.5mm ‘connector on AD-BA200 into your device
via audio output interface. “TV:35mm connector + RCA connector.
STEP 2: Power On
Slide the switch to TX mode and enter pairing status.
*AD-BA200 il connect the last connected devices fistif there is a pairing history, then ) enter pairing mode if connection fals.
STEP 3: Connect To The 1st Headphones
‘The pairing list is displayed according to the signal strength. Press A or W
to select your device, then press OK to confirm connection.
If your device is not i the st try placing your device close to AD-BA200 and press © 1o search again
STEP 4: Connect To The 2nd Headphones.
Hold OK to enter pairing mode and connect the second device by following the
same steps in STEP 3 as you did with the first device.
STEP 5: Repair / Disconnect
Hold OK to repair when connecting to the last connected devices or disconnect
all the connected devices.
*If you only want o disconnect one of your devices when you have already connected two devices, try o disconnect from that device or shutdown that device.
Receiver (RX) Mode
STEP 1: Connect Your Device
Unscrew the twist cap, plug the 3.5mm connector on AD-BA200 into your device.
“Wired Speaker: 3.5mm connector + RCA connector.
STEP 2: Power On
Slide the switch to RX mode and enter pairing status.
*AD-BA200 will connect the last connected devices fistf there is a pairing history. then enter pairing mode if connection fails.
STEP 3: Connect To Your Device
Find “AD-BA200 on your device’s Bluetooth search result and select it to
connect,
STEP 4: Disconnect
Hold OK to disconnect the connected device and enter pairing status.
General Operation
Previous / Next Track
Press A or ¥ to switch audio track. “TX Mode Only.
Volume Up / Down
Press + or = to control volume.
Play / Pause
Press ► to control play or pause.
Clear Pairing History
Hold + and — for 5s at the same time to clear the pairing history.
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement The device has been evaluated to meet general RF
exposure requirement in portable exposure condition without restriction.
Manufacturer
Shenzhen hanke Technology Co., Ltd Address: Meipeng SKY311, Zhongxing Road,
Longgang District, Shenzhen,
Guangdong, China
Made in China
Warranty and Service
This product is covered with Aisidra product and labor warranty for 12 months
from the date of its original purchase.
Any question welcome to contact us:
support@aisidra.com
Extend 2 years warranty:
wvvw.warranty-hub.com
Documents / Resources
|
Aisidra AD-BA200 Wireless 2 In 1
Adapter
[pdf] User Manual
2A2QG-BA200, 2A2QGBA200, AD-BA200, AD-BA200 Wireless 2 In 1 Adapter, Wireless
2 In 1 Adapter, 2 In 1 Adapter, Adapter
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>